Links to the spray guns used in this video: TCP ($35 US): amzn.to/3TC7Bn8 PMT ($62.50 US): amzn.to/3hAvX3s Woolwax Pro ($100 US and my favorite): amzn.to/3Etk20d Woolwax "Supreme" ($250 US): amzn.to/3ErAzSy Lemmer RP-460-HD: amzn.to/3OaQjfR Links to the lanolin products: Surface Shield: amzn.to/3E33vio Fluid Film: amzn.to/3UATVtV Woolwax: amzn.to/3GdtZA8 My Amazon Store: www.amazon.com/shop/repairgeek Help support the channel, buy using my Amazon links As an Amazon Associate I earn from qualifying purchases and your cost is exactly the same.

@johnlastname2895

Жыл бұрын

I recently upgraded from the wollwax pro gun ($99) to the lemmer rp460hd and couldn't disagree with you more lol the lemmer gun sprays 10x better than my wollwax gun ever did and with the pressurized pot no need to warm up the product anymore, it cut my job time in half because it sprays soo much faster , and you adjust the air with the regulator and the product on the back of the gun, I fill the pot with a 5gal pump dispenser works great no funnel necessary and no mess, no to mention the cavity hoses are half the size and fit into waaaay more openings!

@FIVEVEEZEE

Жыл бұрын

Do you have a link to that aerosol can spray wand?

@zw7453

Жыл бұрын

Almost every single inner cavity 360 spray extension nozzle are made for MALE !!!!!! TOP !!!!! SPRAY !!! CAN !!!! NOT FEMALE!!!! Now Surface Shield has female tops on the can, it is IMPOSSIBLE to find any inner cavity extension without paying a ridiculous amount of money for a plastic tube and a brass nozzle! KBS works for an insane price. You can buy extension for male spray can for under $10

Just imagine if all KZread channels were as good as this fella's . What a wonderful platform KZread would be .👍

@RepairGeek

4 ай бұрын

Thanks!

@kenj.8897

4 ай бұрын

@@RepairGeek You betcha buddy , you work hard and it shows

I live in the tropics and I'm watching way more of this cold country content than I need to because of the quality of experience and information provided by this lad. Great videos 👍

A tip for the ends on the end of the tubes. You can use safety wire twisted tightly around the hose to clamp them together and not increase the diameter so you can still get into the holes easily.

the "seated" shimmy motion to show us wiggle crawling around under a vehicle was so perfect

@RepairGeek

7 ай бұрын

Been there too much, why do you think I bought a lift 😂

@MrDefyreality13

7 ай бұрын

i feel that. we got a lift ten-ish years ago. friggin god send. it's tied up with a project truck this year, so i'm back to ramps and creepers for spraying the work trucks this year. thankfully two of them already sit really high so i should be-able to do them on the ground. never under estimate the advantage of a clean, dry, warm indoor space to work in. as a side note, your videos are very well put together, and get right at the real info were after, thanks for making them @@RepairGeek

I reside in Upstate New York State. We get the most snow of any State in the lower 48. We deal with mega tons of road salt, brine and calcium chloride. I undercoat with lanolin products on my trucks. My complaint is that it is difficult to transfer the product into the small opening of the spray bottle. The sprayer manufacturers should take the lead from the mayonnaise bottle makers. Seeing that the lanolin undercoating products are a similar consistency of mayonnaise, they should make the undercoating spray bottled opening the same width as the mayonnaise jars.

I bought the RP460 (I call it the Mack-Daddy) and start with the longest hose to spray inside all frame and body cavities then spray the outside of the frame and underside of the box/cab. I use lots of product and apply it fairly thick everywhere. I had 4 other sprayers already when I bought it and threw out some of them after using the RP460. It is the best at getting the most thick product the furthest into the cavities where it is needed most. Don’t cheap out here guys. It is an investment. Spread the cost out over doing 1-2 vehicles per year for ten years and it is sooo worth it.

Great guy. Very nice delivery of information with tons of practical knowledge

I asked Woolwax about the $250 sprayer attachments being available for the Pro sprayer. “Not available, won’t fit” By far their Pro sprayer is the sprayer to own as a DIYer. Great video, keep it up

With the lack of hose clamp I use a bare single strand copper wire wrapped around the hose at least twice then twisted to tighten.

Such sound and detailed technical advice on the process and the tools involved. Thanks for sharing your knowledge and experience. You represent the true authentic spirit of the Internet..

I'll 2nd the woolwax pro sprayer at $100. It worked fine for me doing my vehicles this year.

I currently use the RP 460 and the $100 Woolwax sprayer. I use the 460 for cavities, hoods and doors. The Woolwax sprayer for frames and underbody coating. I will be upgrading to the Lemmer RP 1202 airless setup next year. 90% of my spraying is NHOU.

Thanks for the helpful info I greatly appreciate it! Hope you have a wonderful holiday season! I have the wool wax pro sprayer coming, and 5gl of surface shield coming Dec ish!

Great video.. Good sound and lighting. Solid info and right to the point. Absolutely helped me in deciding which product sprayer to purchase... Ill be looking for a video about the best product to use next..

Cheers! I found you through Luis Rossman and right to repair. Happily subscribed today, your videos are fantastic!

Thanks for sharing all the details, great video! I went ahead and bought the Woolwax Professional spray gun and undercoated my Toyota Tundra with RP-342. Works really well and I think I'm set for life with that sprayer lol

I bought the Woolwax Supreme Gun and it works well. I use 90 psi and make sure all my connections are right and it works great!

I discovered that when I have poorly match threads (or burred) I can use valve lapping compound. Works great. Apply and cycle, and rinse.

I recently upgraded from the wollwax pro gun ($99) to the lemmer rp460hd and couldn't disagree with you more lol the lemmer gun sprays 10x better than my wollwax gun ever did and with the pressurized pot no need to warm up the product anymore, it cut my job time in half because it sprays soo much faster , and you adjust the air with the regulator and the product on the back of the gun, I fill the pot with a 5gal pump dispenser works great no funnel necessary and no mess, no to mention the cavity hoses are half the size and fit into waaaay more openings!

@Munky332

4 ай бұрын

Yea, but for those of us who are only doing 1-2 vehicles per year, it aint worth the price difference. You're literally spraying goop on the bottom of the car. Get that shit on there and be done with it, don't need some fancy spray pattern when in a week its going to be all black with dirt and oil and shit anyways. Professional wise I could see the argument for time saved, but for the typical DIY'er who's just getting under their car and glooping that shit on to keep their shitbox from turning into a rusted shitbox, who gives a shit if it saves you an extra 5 minutes or so?

I love your videos and attention to detail; if I'm a manufacturing company, I'd be taking notes, and paying attention..! 🧡👍👍

@1920Act

Жыл бұрын

yep, those are supper helpful for DIY ppl!

Great Video - very valuable und helpful information. Thank you for sharing.

I have 2 tcp sprayers one of the older style with a hose and a 360° nozzle attached and another like the style you showed which has a regulator on it and haven’t had any issues with that set up except a plastic trigger on older style slips…

find a cheap square crock pot, fill with water and put on warm, will fit the wool wax bottles perfectly and makes spraying easy

KZread hating on “guns” yet making millions off their videos

@emmvee1678

7 ай бұрын

Someone needs to tell people if the product sucks. Not get lied to by the company selling it and overpricing it.

Great video thankyou for the upload

I have the PMT and it came with the spray wand kit / cavity wands.

Gonna watch it tomorrow, Thanks

Nice review.. fair and balanced

last year I wanted to spray my car, I tried a venturi sprayer. that didn't do it for me so I bought a pressure pot style gun. a really good one that is available here in germany. a 3300 HSDR from Vaupel. it took an hour or two to get used to it but on a sunny day with a tiny tiny compressor I had all things done in the evening. The gun is amazing I think because it also keeps pressure over hours in the pot. it is quite similar to your last one shown, also weirdly small opening but that's ok. I wouldn't want to use anything else anymore. buy cheap, buy twice. and only coat yourself

Great video! After watching you I'm pretty sold on using Surface Shield. I would like to aerosol cans but cannot find the inner cavity extension spray nozzle for Surface Shield. Where did you get the one for this video?

10:02 you can by that hose at lowes or any other hardware store, its like. White Polyethylene Tubing its Item #814305 Model #98584 25ft for 9.28

About 5 years ago I bought a Fluid Film kit that included a gun, extra bottles, wand extension for an aerosol can and a couple gallons of product. What I can't find is extension wands for the gun available to purchase separately.

I've had a lot of problems with Surface Shield cans. I bought 5 and 3 lost propellent at about 50%. Only one was I able to use all of the product in the can. The remaining can I just started to use.

I have the same lemmer rp460hd I bought this fall for my own diy stuff. I haven’t had an issue spraying fluid film with it, although I like it good and thick under there. It’s my own so I paint it on good. I have been able to get it dialed down enough for light application with the air pressure and trigger modulation. The screw on the back is actually not air it’s for the fluid needle spring pressure you can have set so hardly anything comes out. I also pretty much exclusively spray with the wands for everything and don’t use the fan tips. The smaller smaller 90 degree one will spray out less than the Deluxe one. The one thing I do miss is a second container as I was running black and clear fluid film. My clear I had a 5 gallon pump but the black I was trying was just in the gallon cans so it was a little awkward to pour in. I was quoted at $120 for another pressure container which I’m debating on because I think I am going to switch to black for everything minus some visibly panel areas around doors and such.

@alexmoore909

Жыл бұрын

Also I want to say thanks for your tests and reviews. It was because of you I made the switch from having krown spray my vehicles to me spraying them myself with fluid film. I’m fully involved now.

@RepairGeek

Жыл бұрын

My biggest issue with the lemmer is weight. It feels like it weighs 3 lbs when it's full and holding that over your head for hours a day gets hard on your shoulders. It a nice gun but to me it's not $350 nice.

That delay on the Woolwax Supreme gun would be a deal breaker for me… but I watched a video put out by Woolwax from about the same timeframe as this video and their supreme model didn’t have any delay. It appeared to work great, and product came out instantly with the trigger pulls and in a nice pattern. I wonder if the Supreme gun in this video had a defect???

Thanks for the info 👍

by far the best undercoating gun ive ever used is an airless paint sprayer made for painting houses. you can find them pretty cheap used at yard sales. the bigger ones will take a whole 5 gallon bucket and the smaller ones a 1 gallon pail. they put the product out very fast with excellent coverage.

@WilliamVG

Жыл бұрын

I've got a older stand alone Wagner airless, going to rig this up soon.. Glad you mentioned it, should be superior while using it.

Any tips on which regulator I should get for the woodwich pro gun? Thanks for the video.

I am looking at getting an undercoating sprayer to spray my vehicles and maybe a friends. I had been looking at the Fluid Film sprayer kit, but now I see this Woolwax kit and it is a bit cheaper although not a huge difference. Other than number of bottles, is there much of a difference? Also, hard to tell but I'm wondering if the Fluid Fillm kit has smaller diameter wands/hoses and will fit in places better. Any help/info would be much appreciated.

How would you recommend washing the undercoating after applying the fluid film? I'm in Michigan, and I'm buying a new 2023 car. I want to protect it with fluid film, but should I not use a pressure washer to wash the undercarriage after applying it? If I should wash it, I read that people said it'd take it off... and if it does take it off, should I re apply it every 6 months.. every year? If you can help, I'd really appreciate your opinion and time.

Great video!

really like your videos on fluid film, im just did my car with fluid film how do you clean your spray gun after use fluid film

I use a blanket style 5 gallon bucket heater to warm my stuff and then a bucket pump to transfer it into the containers. Mine only heats to 145F but I'm not really sure I would want it any warmer than that.

great job...as usual

Airless gun? Recommended by fluid film. Any options? Especially for the hose to get in the frame?

About compressors: You can get away with using a small single stage air compressor for something like this. Something like 4.7 or 5 gal works fine as long as its the kind with 2 tanks. I forget what you call them, but if you set them up properly they work like a 2stage and they will run a cup gun or gravity feed just fine. I used to spray contact adhesive through a cup gun with this setup, so I know it will work with undercoat.

can you use a airless like graco or a paint sprayer?

I have the woolwax gun and bottles kit, and am thinking of switching to surface shield. Can I pour & run surface shield through my existing woolwax setup?

I now use a franco airless paint sprayer. Works great but I do multiple vehicles a day

i just loved your video can you send me a link as to where i can purchase those 3 plastic bottles like showed i am very interested & so was your video just great video with really super nice explanation 👍👌

Any thoughts on this sprayer? Looks like it can do truck bed coatings also "TCP Global Air Rust Proofing and Undercoating Gun with Gauge & Suction Feed Cup, 2 Wands - 22"

Can you slip a tube over the end of the cheap Amazon sprayer to get the product into the frame rails?

Have you tried the wide pattern tip for the supreme gun? Wont that cut the time in half spraying vs the pro gun? How wide is the spray pattern on the pro gun? I have a truck which is why i ask

Which gun that you reccomend 2 shoot slip & do you degrease the undercarriage of the vehicle 1st & what you use 2 degrease it with

How hot are you getting woolwax before spraying it. Im spraying it in 80ish degree ambient temps and it hardly flows. Im noticing not much at all is making its way out of my 360 wand extension.

Is there a 10 gallon you recommend? Thanks.

Do you need a pressure regulator for the whoolwax pro gun 100$ ?

What is the difference between a setup like this vs the Graco fireball 300 15:1?

Can I use a HVLP Sprayer for Mastercoat? Doing a superduty bedfloor replacement. Bed is off truck upside-down on the ground. I also have my Raptor liner and woolwax sprayer. Can I use either one of those? Thanks for all the valuable information you have given us

@RepairGeek

Жыл бұрын

HVLP should work fine thin it a little bit with mastercoat's thinner worst-case scenario. I used a suction with a 1.8mm tip and used a cap full of thinner on my 3rd coat.

What is the CFM requirement for the woolwax pro gun?

What do you use for a respirator?

Your vid’s have been extremely helpful. I got the Woolwax gun but the wands are too thick for doors and inner cavities. Do you know of any thinner wands which will fit or another gun which has thin wands?

@RepairGeek

7 ай бұрын

The cheapest option would be aerosol with an adapter.

@Spta97Vids

7 ай бұрын

Thank you. Seems in order to get a thin nozzle you need to get a pressurized gun. The Woolwax gun works great for the undercarriage but since it uses the Venturi effect it needs a larger diameter wand. So I’ve been told.

Do you have a video on how you clean your guns?

Excellent

Surface Shield cavity sprayer shown?

Thanks!

15:57 is it missing or suppose to have a o-ring on the pot?

Can you aDD Anything to the Surface Shield to make it black like the black version of Fluid Film they sell? If so, how much to add to the gallon container? Thanks

@RepairGeek

5 ай бұрын

Graphite powder works. 3/4 of a cup to a gallon.

Just curious, what do you clean the sprayer with when your done using it? Is it safe to let the product sit in the applicator can or should it be cleaned out and flushed with something?

@RepairGeek

6 ай бұрын

The lanolin products don't dry. You can leave the gun full and come back to it 6 months later. It will work just fine.

It just started snowing here in upstate ny, and they already salted. I want to undercoat my truck, do I have to wash the whole underside and let it dry? Or am I able to undercoat it if there is salt on it?

@so2315

Жыл бұрын

I would wash it off, leaving it on and then spraying just entraps the salt against the frame. And 6 months later when the woolwax is gone the salt may rear it's ugly head.

I would use safety googles / face shield to protect eyes .

I thought you were going to call them underbody sprayer and not the "g". Did not hear you say that once whole video lol GOOD INFO!

Has anybody , adapted the supreme gun's quick change tip to the pro gun's tip? Are the threads different?

Hi, what about HVLP sprayers, Specifically devilbiss flg 6? The gunman KZreadr highly recommend it

@RepairGeek

Жыл бұрын

I'm not a big paint guy. I have no opinion on paint sprayers.

I haven't tried it yet, but I've been told a pump sprayer like what you'd use for Roundup works with fluid film, so that could be a cheaper option too

@leightonreese1832

7 ай бұрын

I tried it, did not spray fluid film well at all, I had to cut it w/ vegetable oil to get it to flow and even then it came out as more of a stream 1/2 my product ended up on the ground from dripping because the garden sprayer could not atomize the fluid film

@dballer51

7 ай бұрын

@@leightonreese1832 Well, thank you for trying that for me, that's unfortunate that it didn't work though

@Nimesh222

4 ай бұрын

I wonder how the jacquard refillable Youcan would work with fluid film, will have to give that a shot.

What's the shelf life of unused product? I want to use the 1gallon container so I can use a gun with extensions for inside cavities, but I doubt I'd use a whole gallon on my car. Will the unused portion be good next year? Thx

@RepairGeek

Жыл бұрын

It will be fine. The bulk product will have no issue lasting 5 years or longer in the container.

@daveshane957

Жыл бұрын

@@RepairGeek Thanks, I love your undercoating videos, I live in northern wisconsin and everything here turns into a pile of rust. I wish I'd known some of this stuff years ago.

@daveshane957

Жыл бұрын

@@RepairGeek Another question, would it make any sense to use one of the rust converters first, then use the undercoat over that? I'm trying to save a 2000 Jeep XJ, Thx

Why are you still using all three products? I see fluid film being the cheap option and surface shield being a better product because of the petroleum jelly and 2 yes, but where does wool wax fit in?

I have the NHOU version of the woolwax $100 sprayer and just got the woolwax supreme sprayer. The $100 is better! The supreme one has issues with the air and product flow both fading away at different times, first the product will slow down but it's still spraying as hard as it was then I will get the product back and then the air pressure will fade away. AND THE REGULATOR HAS THREADS THAT DON'T FIT ANY AIR FITTINGS OR ANY OTHER FITTINGS TO ADAPT IT AT THE HARDWARE STORE! on the plus side they did say they will send me all the new attachments for the supreme for free.

@johnnymissfire8464

Жыл бұрын

@The Hemwick Hag a 120 gallon 5hp 3 phase. Actually the last time I used the supreme gun I granted the pressure to 125 and it worked like a dream.

Your woolwax pro sprayer with the 3 bottles etc, what is the best air pressure setting to use for fluid film? Is there any other adjustments ? I bought years ago but haven’t tried it yet?

@RepairGeek

Жыл бұрын

60-80 psi

@4Runner123

Жыл бұрын

@@RepairGeek thank you for the reply just picked up a new 4Runner need to spray it. This episode came at a perfect time . Have sprayer and a gallon of fluid film.

What can I use to slightly delute Woolwax? Thank you

@RepairGeek

Жыл бұрын

Call them and ask.

@BladePilot24

Жыл бұрын

Vegetable oil is what they (WW) say in their video.

any chance I can use my magnum x5 airless sprayer for this? thank you.

@RepairGeek

Жыл бұрын

Probably but you'll want to make it a dedicated undercoating sprayer afterwards. I have no idea how these oils are going to react with paints.

@garyconley69

Жыл бұрын

@@RepairGeek Got it. Thanks for getting back to me. and thanks for all the information you provide. Have a good weekend.

What do you use to clean out the sprayer, tips and wands?

@RepairGeek

Жыл бұрын

Nothing. These lanolin products don't dry. So you can spray a car, put the gun on the shelf and come back to it a year later. No issues.

@bdubs6205

Жыл бұрын

@@RepairGeek appreciate the reply! But say I did want to clean it out. What would be best?

@RepairGeek

Жыл бұрын

Mineral Spirits.

I personally own the lemer 460 and the only thing I agree with what you said was that you can't adjust the fluid volume though. The rest your off base. Its primary job as a professional gun is to be used with wands. I recommend switching the gun and attachments to regular sized air fittings as there easier to come by and much cheaper. I've made many wands and by saying where the small angle one will fit in comparison to the deluxe swivel one is off the small one works great for getting in door bottom holes I went as far as cutting my small wand at a 45 degree right at the bend and smashed it together so it fits in the small door holes and atomizes to a very fine spray. I've put NH Oil, fluid film, and some wk sealout which isn't availible to the regular public. It's a great gun it's built to a much better standard then the other ones. It's not built for doing the entire underside of a car. It's built for cavities and crevices.

@RepairGeek

Жыл бұрын

That is my point exactly. It works great for inner cavities but $350 is a lot of coin for a gun that is dedicated to inner cavities only.

@MegaMajormax

Жыл бұрын

How do you switch the fittings on the gun and wands?

@bauscustomdetailing8876

Жыл бұрын

@@RepairGeek I spray 100's of vehicles a year with lemmens sprayers. You need to have more experience spraying before giving info like this.

@ryanwilson3632

Жыл бұрын

@@MegaMajormax There's a quick release like an air coupler to change out lines. I've also made a ton of custom lines for mine, which is why I changed out the quick coupler to more readily availible stuff.

@MegaMajormax

Жыл бұрын

@@ryanwilson3632 I see, thanks for the info. Is this only for convenience or does it last longer with the different fittings?

What do you use to clean the sprayer?

@RepairGeek

Жыл бұрын

I dont clean them. Any of the lanolin products don't dry so I can put them on a shelf, come back to it 6 months later and they still work perfect. As far as cleaning is concerned I wipe the outside off with a rag. That's my gun cleaning regimen haha.

What about using an inexpensive (200-300$) airless sprayer (up to 3000psi)?

@RepairGeek

9 ай бұрын

I've heard good things about using one of those. I've never used one myself.

Where did you get that Surface Shield inner cavity adapter?

@zw7453

Жыл бұрын

Almost every single inner cavity 360 spray extension nozzle are made for MALE !!!!!! TOP !!!!! SPRAY !!! CAN !!!! NOT FEMALE!!!! Now Surface Shield has female tops on the can, it is IMPOSSIBLE to find any inner cavity extension without paying a ridiculous amount of money for a plastic tube and a brass nozzle! KBS works for an insane price. You can buy extension for male spray can for under $10

@santoro2020

11 ай бұрын

@@zw7453 Funny you mention that, I ran into that problem too.

@ericfinch9642

11 ай бұрын

Was your question answered ? I didn't see a good answer.

@santoro2020

10 ай бұрын

@@ericfinch9642 Sort of. About a year ago, Blaster changed their cap design which renders the adapter useless. I haven't found a feasible alternate to the new design.

has anyone tried using ryobi airless sprayer with surface shield?

Can you undercoat my car since I think I'm in your area? Based on some of your older videos I think I'm not too far. Thanks!

I just want a premium cavity wand that I can get into the drain holes on the bottom of the doors. It looks like all are good it one thing but not everything

0:36 I was trying for too long to figure out why somebody would call them "gay sprayers," and then I saw the first comment and face-palmed. 😂

How do you fill WoolWax Pro bottles?

@RepairGeek

Жыл бұрын

Surface shield I can just pour it in. Fluid Film or Woolwax need a pump or a spoon lol.

I usually use my hands or pour it over from the roof and let it drip in. On a hot day, it gets in all the cracks.

do you recommend the woolwax pro sprayer for fluid film? Also would you recommend thinning fluid film with wd40 or is a hot water bath enough

I have a crazy idea. Maybe it's worth for you (from the content perspective and "science") to try it out and make a video about it: What about refilling empty spray cans or any kind of aerosol cans with undercoating products and use compressed air for the propellant? There are a lot of videos out there showing the process but I wonder if it's possible to fill them with undercoatings. So this could be a method for the broke folkz, no need for an expensive and large air compressor. A regular air pump should be enough to "fill" the spray can. What do you think?

@ShainaReed30

Жыл бұрын

They make aerosol cans that you can pour the liquid in and fill up with compressed air and spray but would take a pretty long time. If nothing else can go get one of those little pancake air compressors at harbor freight or Home Depot maybe?

@Nimesh222

4 ай бұрын

Something like the jacquard refillable youcan ?

ok saw your link duhh😅

I'm doing a "gun" counter!!! lol

@RepairGeek

Жыл бұрын

Lol don't. 😆 The PMT I don't think I said sprayer once. Got to the edit and said screw it lol.

Hey brother do you undercoat cars? Not far from you. Thanks

Not sure where you're getting $350 for the lemmers I use it daily everyday and it's $250 for that gun. Also a pancake air compressor is more then enough. No need for a large compressor.

@RepairGeek

Жыл бұрын

Check the link in the pinned comment and the description for the lemmer. 335 right now...

Air pressures to high causes low transfer efficiencies , with these guns /sprayers that are siphon feed are very low, take a hint from what the automotive painting industry changes over the decades... everyone (smart) converted to gravity feed guns... what you are spraying.... a pressure feed sprayer is the best! To keep your products viscous, get a old hot plate put your 5 gallon pail of water on it and.... voilà a thin viscosity product....your welcome!