I didn’t think gimmicky bits (like Atomic and Bearing) would work in X until this video. It’s a very neat concept and I’d like to see them make a return.

@SJ-Lakui

24 күн бұрын

Why would they not work?….

@moomoo189

24 күн бұрын

Atomic still probably won't work as the purple ring is free spin, making it unable to use x dash

@SJ-Lakui

24 күн бұрын

@@moomoo189 just make the ball free spin, with another layer cap to the gears

Variable with Beyblade X speeds would actually be amazing, imagine how fast the rubber would wear down

Imagine a Quest Bit. 😂

you can probably launch a burst bey with volcanic in an x stadium and it would work completely like an x bey lol

I think most players do not want equalizing beys. Everything else you said is on point. In all seriousness, however, in my opinion, Takara Tomy creating a balance between old and new types of bits is good.

OP Bearing would be possible for X just like all the other gens

@lumieretheforgiven3804

18 күн бұрын

Unless it's as tall as disc ball then it would be too op which is terrible for healthy gameplay

@rolfthebolf

15 күн бұрын

Bearings weren’t meta breaking in other gens… just burst because of the weight creep

I’m a simple man I see unite I click

imagine making the bearing bit concept into bearing drive from phantom orion lol

If they would put BB drivers in X, fans would just complain about Beyblade X not being very original

For my ONLY opinion, I do not agree adding bearing nor Atomic since there's a lot of Beyblade x Blades that are heavy and mixing these Parts in a future competitive play might making the meta so unfair unlike Burst tournaments, There's alot of bladers that still use Bearing parts since the Type Meta is unfair.

Part 2 please !! I like it

Blow is just taper. I mean look at how much wider flat tips are in general in x taper is just blow after it’s been carried over to x proportions (same with point being the x version of the fusion driver)

Amazing

Awesome🎉

Just look at HMS Bey's running core all the gimmick are there but without the gear

How can I get some of thouse tips for me

@sunnysxbeys

17 күн бұрын

The BEYBLADE X bits are only concept arts

I don't think the bits that change their height is good. (The variable and nothing you said) It could ruin how the gears interact with the rails

@richardtaveras3593

24 күн бұрын

Don’t low and high bits already alter height?

@Thunderdransword

24 күн бұрын

No the tip and the gears are unchanged it’s the ring in the middle that changes the height

@DaApplely

23 күн бұрын

@@richardtaveras3593 basically if you think about it, the gears are in a position where they can align perfectly with the rails. By changing the height on the middle part, it doesn't alter how the gears interact with the rail. However if the bottom of the tip changes height, the gears will get affected and it might hit the middle part instead of hitting the gears

@DaApplely

23 күн бұрын

@@Thunderdransword here's an example. If you decide to cut off a bit of the driver like Flat to try and create like a low Flat. That won't work cause the gears no longer align with the rails and are more likely to hit the middle part than the gears itself

@Thunderdransword

23 күн бұрын

@@DaApplely Ik I’m talking about the part in between the tip and gears part and the shaft

BEANS

1) Blow driver variant would be nice in addition to Rush bit. Less tall (than R) but small surface area 2) Every part is free spinning. Since the gear is spinning too, wouldn't that interrupt the performance a little bit, like being less aerodynamic(?) 3) Quite interesting because the bey will be at its top speed longer than BB. Maybe lower the gear ratio 4) I always wanted, at least to have awakening feature. Volcanic/Hold would be insane though it's gonna ended up like Quake bit 5) Didn't know Keep driver rubber ball was free spinning 😮... But yeah easily outclass by Needle bit 6) I'm actually okay with hard rubber for attack purpose since it's not gripping that hard like Xtreme driver soft rubber while able to keep the BX (Xtreme Dash) identity in check. The gear ratio shown was reasonable 7) Cannot say that much with soft rubber(?) as defensive purpose. I personally don't like going back to stamina battle 8) Again, only hard rubber looks promising for BX standard 9) It'll costs many people money because breaking the disc over and over after performing attack (still an interesting concept since I really like awakened Wave driver) 10) Saw a comment said it's not practical having a BX changing height and I also agree. Plus, a comment from other Weiss Tiger said Unite bit kind of performed like Dimension driver with a wear off rubber tip 11) It's overkill and the design of it having many gears ratio is a bit funny because it's intended for offensive bits (Accel, Hexa) but this was made just to cover the free spinning plastic area to avoid breakage

Ahh sweet if this really happened!!!