Just replaced my middle hinge after watching your video, it was a great help. A couple of things i did also, was to mark around the old hinge which is attached to the door with a felt tip pen. That way you can be a lot more accurate with the new one. Also you can adjust the jack as you go along to help you lift the door in place. Cheers.

@WonderingWomble

3 жыл бұрын

Hi Bud.. Glad it helped you out.. Felt pen is a good idea.. Its a Ford so there is a outline of rust to follow.. Haahaha.. Thanks again

Like others in the comments, this video was of great help mending my middle roller after a few years of abuse caused it to break off! Thanks for sticking this up.

@WonderingWomble

Жыл бұрын

I am so glad that it help you.. Thanks

Thank you very much.

@WonderingWomble

11 ай бұрын

always a pleasure

My 2010 transit connect need the top one changed. There are three on the connect. Good video for the lower two.

@WonderingWomble

5 ай бұрын

Thanks.. I have had to replace them again since this video.. Cheers

@sethdawg

4 ай бұрын

@@WonderingWomble I ordered part from turkey to Hawaii only $20 I now have a perfectly sliding door!! Upper roller was toasted had a flat spot. Now perfectly smooth no issues whatsoever! Cheers.

@WonderingWomble

4 ай бұрын

@@sethdawg so glad the video helped.. Great stuff

Hi many thanks for this video, i have a 2005 ex Royal Mail Transit - as you can imagine, the rollers on mine had virtually nothing left of them with the side door being used every few minutes in its former life, i used your video which was well explained, to fit my new rollers and all went well, i don't wake the neighbours anymore when i open and close my door lol thanks Buddy.

Thanks for making this video. I used it as my guide to fit replacement rollers on my van. So clear, even I could follow it. Happy camping from Jim.

@WonderingWomble

3 жыл бұрын

Thanks Jim.. The rollers on Transit's never last very long.. The door is so heavy.. But once you have done it once, it so easy the next time.. Cheers Bud

Just replaced top and bottom runners on my 2009 Fiat Ducato van. Tried the AFTER MARKET guys and all three of them offered me the wrong parts! Phoned the main dealers who required the Original Reg Number and then sent me the correct 2 parts, cost me £164.23p but saved credit notes; and my knuckles etc. Watched you're video to make sure I'd done almost the same thing AND Yeeee Haaaa, the satisfaction was overwhelming. Thanks for you're video, next time I'll get Spielberg around to video my new talent..talents! I might add I 'DID NOT' mark around the old runners as with their wear and tear on the worn runners, I could have fitted the new one's in the wrong place's.

@WonderingWomble

2 жыл бұрын

Hi Kevin.. I think its always best to have original parts but the price always put people off.. So glad you enjoyed the video.. Cheers Bud

I had the exact same problem and I have a twin wheel jumbo. Still hits the pillar.

Very helpful 👌

@WonderingWomble

2 жыл бұрын

Thanks Peter

👍

@WonderingWomble

2 ай бұрын

👌

Hi - to make adjustments do you loosen/ tighten the two bolts that attach to the door ? Thanks for the video!

@WonderingWomble

3 жыл бұрын

Hi.. I found the adjustment very difficult. as you have to do all 3 rollers. then have to do them all again as one put another out of line. I start with the top, then the middle, the bottom is just for lining up the door closure.. Its all trial and error to get it right.. Cheers

Have you replaced the top one? We replaced the middle and the door os still struggling to open (like it did when the plastic around the bearing went). I bought the 3 pack and am going to replace the top and bottom. Did you just use the standard transit jack to support your door too? We wedged ours still on our step with some planks of wood 😂🤦🏼‍♀️ thanks!

@WonderingWomble

Жыл бұрын

Hi.. Its the top one that carries all the weight of the door. I replaced all 3. But do them one at a time. so you get the door lined up. I used a trolly jack to keep the door at same hight.. No fun on your own.. Cheers

Yes, the old one was worn to a smaller diameter. I would be surprised if the door wasn't sticking out further. Mine is having troble poping out and it won't open, unless I close it hard, lock it again, unlock and open quickly. Must be the spring on the middle mount.

@WonderingWomble

Жыл бұрын

They wear out so fast.. I have tried several type form different suppliers even the one with a rubber tire on it.. I think its a bad design and the door is too heavy, plus mine is a camper so the extra weight of insulation and liner.. Cheers

@gacattack1234

Жыл бұрын

@@WonderingWomble Thanks good info to know. I will have to work extra hard on cleaning the track and the lubrication as I'm not expecting high quality parts unless I can find some OEM.

@WonderingWomble

Жыл бұрын

Mind.. too much grease on the middle runner and all the road dust and salt will stick. I just clean mine with a dish mop and only grease the roller it self.. Glad to help..

Very helpful video - thank you :-) I'm still confused about this 'extended' central roller, tho' - if an extended one IS needed for the twin-wheeled Transits, then surely extended top and bottom rollers would also need to be fitted to match this extra clearance? How can the middle be 'out' further than the top and bottom? Cheers.

@WonderingWomble

10 ай бұрын

Hi.. Both top and bottom roller are at the front of the door. so when open they will be in the same door opening.. Middle roller is at the rear of the door.. You only need to extended middle roller if your transit has extened wheel arches. the rear hinge will then bring it out far enough to open the door, plus they have a different slider rail..

@Pityssakes

10 ай бұрын

@@WonderingWomble Many thanks. Good to have my D'oh! moment confirmed 🙂 Cheers - now to get the parts...

The top of my sliding door Mk7 sits slightly further out. Will adjusting the middle help? Cant work out. It was like it when i bought the van

@WonderingWomble

8 ай бұрын

Hi Alec. There is slight adjustment on the top roller as well. The centre one will lift or lower and pull the rear of the door in.. If the door is out at front top, make sure the guides on the door post are lining up, you can adjust them as well. I would adjust the top one first, take the weight of the door on a jack.. Cheers.. let me know

@alecnewstead2478

7 ай бұрын

@@WonderingWomble thank you for the reply. I will do

Did you do the top roller as well?

@WonderingWomble

4 жыл бұрын

Hi Nero.. Yes. I replaced all the rollers.. All Mk6 and Mk7 Transits are the same. except the transits with plastic rear arches.. I still say its a 2 man job.. I found the order of fitting is to start with the bottom one, and keep closing the door and alline each roller as you fit it. then the top one. and the middle last.. Cheers Bud

@kevinprivet5942

2 жыл бұрын

Did it look like it? Dimebar.

My side door struggles with the first bit of opening where the door comes out away from the van if I push it from the inside then it will pop out and slide freely but it's almost impossible to open from the outside any help would be appreciated

@WonderingWomble

2 жыл бұрын

Hi.. By the way you have described that. The top roller has lost one or two of its bearings. I got mine from "Transitparts.co.uk" and as you see, its very easy to fit. But I do say its easier with 2 people

As soon as i see the extended roller you bought I thought OOpps!! If you bought that roller of the well known Transit parts seller on Ebay then they are fully aware of the problem of it not fitting. As you say, it's for a twin wheel Jumbo. But it won't fit a twin wheel Jumbo Bus, because of the door pillar and the roller fouling. I think it'll only fit a T/W Jumbo van I had to do a lot of fettling to get it to fit properly. Yes I have a Jumbo bus, and wanted to get the door to open fully. This isn't a simple job, and wouldn't recommend it without a good workshop. Glad you got it sorted in the end, and all's working OK. CVD

@WonderingWomble

6 жыл бұрын

Hi.. Thanks for the comment.. I used to have a garage until i retired.. I sort of new it was the wrong one, but took their advice..? in the past I have had 3 buses and converted.. All I had to do was move the bottom roller, they bolted it in a different position on the door..???? they were single wheel thow..? The only thing i need now is the side door lock, it is in the middle of the door and not at the back like all the vans, as i have put my kitchen part over the door way, i can no longer reach the inside lock, and have to use the fob, but when i do that it sets the alarm and the dogs set it off in the night. The only way to get over that was to use the drivers inside manual lock, and that just locks without setting the alarm off..? any ideas..??? Thanks again.. Kevin

@krustykamper

6 жыл бұрын

Yea I thought all I had to do was move the stop and rollers. But on my twin wheel bus the center roller guide is too short because of the windows. So i had to buy a full length guide and bend it to go over the window glass. Then cut out the upper part of the step and remake the roller guide. Check out my the pics on my channel if you want to see what I had to do, Door mod starts at about 1.20min In hindsight I wish I had bought a Jumbo van instead of bus to convert. Happy now it finished, but what a bugger at times...lol CVD

@WonderingWomble

6 жыл бұрын

Hi again.. Thanks for that.. Yes I had already seen your pics before i replied to you.. Not really every seen that before, i thought that all buses are van derived..? But it is very very rare to get a high top bus.. think i'v only seen one before..? It did look very fiddly to do.. but well done.. I also see that Jay & Loura from "Campervan handyman" has commented.. I should be going up to see them soon, to help out with the wiring.. always a problem wiring..? But i believe his van is coming along great.. Again Thanks.. Kevin

@krustykamper

6 жыл бұрын

Yea i was really lucky to get the Hightop, right place right time I guess. I'd only ever seen Midtops before. Mine left Ford as a Bus not a van conversion, so don't know if that made a difference. I like Jay, he's got the same silly sense of humor I have. I know he's struggling with the weather at the moment with his conversion, and as you say, wiring PITA and bain of my life I do hope he gets a break, he needs it. I promised him a "BBQ hamburger" when he gets this way (In Joke) CVD

@tonyfrancis9793

5 жыл бұрын

Did I miss it or did you not include the replacement of the top roller??🤔

What is call this adapter socket for star bit ??

@WonderingWomble

Жыл бұрын

They are called in uk torque bit, as for what size, i cant remember sorry..

You said the replacement was an allen key yet you used a torx bit to readjust the bottom roller.Good video though.

@WonderingWomble

4 жыл бұрын

Hi Andrew.. torx will fit Allen, but Allen wont fit torx. It's an old person thing. Ya just do it without thinking.. cheers bud

@andrewsaunders1796

4 жыл бұрын

@@WonderingWomble I know what you mean but I'm heavy handed and usually round bolt heads off when doing this stuff. Still a great video though.

What tools do I need?

@WonderingWomble

Жыл бұрын

Hi.. You only need some hex bits, and allan key and spanner for adjusting the top roller. I also had a jack to help hold the door up as I fitted them..

@redraspberry9825

Жыл бұрын

@@WonderingWomble thanks, do you know what sizes?

@WonderingWomble

Жыл бұрын

Top I think spanner was 17mm and 8mm Alen, you need 3 hex's for the others, T25 T30 T40.. The bottom roller has some times got a 13mm bolt and some have T25 bolt..

60 years old and you can't spell yesterday! Hahaha😜! Good vid though. Cheers.

@WonderingWomble

4 жыл бұрын

Hahaha.. I'm a little older than that now, and it's getting worse..

@kevinprivet5942

2 жыл бұрын

Do one crank.

@punxneverdead666

2 жыл бұрын

@@kevinprivet5942 😭😭😭😭