Timing Belt / Waterpump Replacement: Toyota & Lexus V6

Автокөліктер мен көлік құралдары

Step by step DIY Video on how to replace the timing belt, waterpump, camshaft and crankshaft seals, idler pulleys and tensioner on a Toyota or Lexus with a V6 engine.
Procedure is the same for all 1994-2006 1MZ-FE (3.0L) and 3MZ-FE (3.3L) engines, with the newer engines differing only in the timing belt tensioner bolts.
Procedure is straight forward starting with the removal of the dog bone mount, engine support bracket, alternator and power steering belts, crank pulley (harmonic balancer) and timing belt covers.
Once access to the timing belt is achieved, the tensioner is released so the belt can be removed. The camshafts should be removed to get to the waterpump, otherwise two studs running through the waterpump have to be removed.
Special tools required are an impact wrench and air ratchet (not mandatory), a seal puller, a pulley puller, torque wrench, and a crankshaft and camshaft holding tool.
This job should take 4 hours for a DIY'er with moderate mechanical aptitude. The Aisin timing belt kit with waterpump from RockAuto was used.
After the removal of the cam and crank bolts, the hardest part of this job was dealing with the rear camshaft seal and aligning it with the marks on the timing belt. Access is tight near the fender wall and removing the power steering fluid line and reservoir is recommended.
The AISIN Timing belt kit can be found here on Amazon:
amzn.to/309Udve (US)
amzn.to/2XN3M5J (Canada)
The Cam holding tool can be found here:
amzn.to/2XPNQjb (US)
amzn.to/2LDWX03 (Canada)
The seal puller can be found here:
amzn.to/2JdTVxV (US)
amzn.to/2RSOpn3 (Canada)
Harmonic balancer puller:
amzn.to/2RYrqHk (US)
amzn.to/2S3uRMZ (Canada)
Link to Etsy shop where you can purchase speedkar99's brother's socks, t-shirts or hoodies:
www.etsy.com/ca/shop/Speedkar
Check out the speedkar99 Facebook page:
/ speedkar9
Check out the speedkar99 Linkedin page:
/ speedkar99
Follow speedkar9 on Instagram for behind the scenes coverage:
/ speedkar9
Subscribe for more videos just like this:
kzread.info_...

Пікірлер: 1 300

  • @speedkar99
    @speedkar995 жыл бұрын

    The AISIN Timing belt kit can be found here on Amazon: amzn.to/309Udve (US) amzn.to/2XN3M5J (Canada) The Cam holding tool can be found here: amzn.to/2XPNQjb (US) amzn.to/2LDWX03 (Canada) The seal puller can be found here: amzn.to/2JdTVxV (US) amzn.to/2RSOpn3 (Canada) Harmonic balancer puller: amzn.to/2RYrqHk (US) amzn.to/2S3uRMZ (Canada)

  • @joonajks

    @joonajks

    5 жыл бұрын

    Good morning, I accidentally turned the crank before installing the new Timing Belt. Top dead center has been set before removing the old Timing Belt. can I turn the crank 360 lined up with the mark without the belt attached to it?

  • @jkvlogs7396

    @jkvlogs7396

    4 жыл бұрын

    Brooo where are you

  • @joonajks

    @joonajks

    4 жыл бұрын

    Jithinkakkur Kakkur Atlanta! I’ve figured it out and everything is all good!

  • @jkvlogs7396

    @jkvlogs7396

    4 жыл бұрын

    @@joonajks ok broooo. God bless you

  • @lmtdgvrnmnt3918

    @lmtdgvrnmnt3918

    4 жыл бұрын

    I'll be doing this to my highlander. How long did this take?

  • @panchoVilla979
    @panchoVilla979Ай бұрын

    I watched five separate repair videos on this subject from hour long professionals to 30min beginners. I'm a fair mechanic but I was about to give up. Stumbled on to this 15 min video and instantly knew this guy knew what he was talking about, and more importantly, he knew how to explain it so well I could clearly understand it. The best KZread video on auto repair I've seen, ever.

  • @VASailpwr
    @VASailpwr9 жыл бұрын

    This is without a doubt one of the best car repair videos I've ever seen. No bs, good edits, good info. Thanks!!

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    Thank you very much for your feedback!

  • @RGMDG

    @RGMDG

    5 жыл бұрын

    I totally agree. Going to do my 98 ES300 This weekend. Wish me luck.. I am sure it will be fine. I am setting aside the whole day to Git-R-Done..

  • @edcain3676

    @edcain3676

    4 жыл бұрын

    Is Everything Pretty ,Much the Same for the 3.3 Eng.? Great Video& Does the Crank & Cam Seals Come W/ the Aisin T.Belt Kit? Tks in Advance

  • @jrh11254

    @jrh11254

    4 жыл бұрын

    Robert Martin - how did it turn out??

  • @BenHelweg

    @BenHelweg

    3 жыл бұрын

    I can't believe how many deviations and confusing instructions the Haynes manual gives compared to your simple method. It might have been good to list how to torque the harmonic balancer down though at the end for those without access to an air gun.

  • @sirobb
    @sirobb9 жыл бұрын

    I also do maintenance videos on my channel so I know just how much extra time this would have taken you to film and edit so you could share your knowledge. You've done a great job!

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    Thanks!

  • @user-qh5ir6kw2g

    @user-qh5ir6kw2g

    6 жыл бұрын

    大家好

  • @smithraymond09029
    @smithraymond090297 жыл бұрын

    Of all the timing belt videos I've seen I must say this is the clearest, straightest one yet. Simple, no bs. Very close up and detailed. I have a different type engine (1UZFE V8) but the basics on removal and aligning the belt are the same. Great vid.

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    +smithraymond09029 Thank you for the feedback. I'm glad you like my style, short and to the point. No need to bore the audience with BS.

  • @mann_idonotreadreplies

    @mann_idonotreadreplies

    2 жыл бұрын

    "simple no bullshit" but the water pump is driven by the timing belt Hahaha.

  • @GTOoo

    @GTOoo

    2 ай бұрын

    I assume the 1UZFE is for the LS400? If so, was the process the same? Thanks.

  • @twangshui
    @twangshui9 жыл бұрын

    Among the best DIY videos up here - yours are clear, precise, and perfectly edited. Thanx for not wasting my time with blah blah blah blah blah!!

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    Thanks for the feedback!

  • @DanLoFat

    @DanLoFat

    7 жыл бұрын

    O ya, excellant, by far the best explanations with actual doing (not just "saying" what I can read in a manual!).

  • @aldogaray1374

    @aldogaray1374

    7 жыл бұрын

    speedkar99 hey man im doin this job on a 1990 lexus es 250 with v6 engine i line up the mark on the main engine pulley but the ones on the cam pully wont line up there is one mark already on the cam pulley do all 3 have line up because they wont on this car

  • @DavidParker-cf2km

    @DavidParker-cf2km

    6 жыл бұрын

    aldo garay - Turn the engine over one more revolution. it is a 4 cycle engine, depending on your starting point, you may need to turn more than one revolution to line up the marks. It is top dead center #1 you must reach to line up the cam pulleys.

  • @40redman

    @40redman

    6 жыл бұрын

    You definitely have a good approach to the repair process without all the extraneous b.s. One of the best videos I've seen

  • @djkurious
    @djkurious9 жыл бұрын

    Thanks for this video. Changed a V6 Camry timing belt/water pump/tensioner for the first time. Took about 4 hours from start to finish wit this well detailed video.

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    I'm glad the video helped!

  • @markrumble7706

    @markrumble7706

    4 жыл бұрын

    You saved yourself about 800

  • @sunnysingh8483

    @sunnysingh8483

    2 жыл бұрын

    It only took you 4 hours? Wow! I thought it would be around 1-2 days. Maybe it’s my ocd kicking in lol

  • @BenotzJoe
    @BenotzJoe9 жыл бұрын

    Thank you for the most useful video on KZread. I did my 2000 Avalon almost exactly as shown: 10 hours with preparation, lunch and cleanup. I found it easier to drain and removed the power steering reservoir so I could move that hose out of the way; my fluid was brown anyway. Also, I had a third pinch screw holding my alternator. Your most useful comment was on how to remove the crank screw using the starter motor. Brilliant. When I loosened the screw, I did not disconnect the ignition; I used my unchipped key which turns the engine but does not inject fuel. Thanks again!

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    I'm glad it worked out for you and your car is up and running again.

  • @40redman

    @40redman

    6 жыл бұрын

    I like the idea of using the 'unchipped' key. That might come in handy when I perform my replacement. Also will keep in mind draining the power steering fluid.

  • @DIYOneForAll
    @DIYOneForAll6 жыл бұрын

    Great job with the filming and editing. Honestly, I don't understand why someone would dare to dislike this video.

  • @speedkar99

    @speedkar99

    6 жыл бұрын

    +DIY OneForAll glad it helped. They'd dislike it because it's above thier mechanical skill...which we can't help.

  • @FranciscoGonzalez-ro7ht

    @FranciscoGonzalez-ro7ht

    5 жыл бұрын

    Your right.. I do maintenance in my vehicles and if it happens to replace the belt I'll follow the procces in this video. It's all clear

  • @Ray-hg3ie

    @Ray-hg3ie

    4 жыл бұрын

    @@speedkar99 Before watching your video, I could not spell MECHANIC...….NOW I are one!!! Great Job man, thank you so much. Don't let the goof balls get to you. Many of us appreciate your help.

  • @edbo10

    @edbo10

    4 жыл бұрын

    OP doesn't realise that people will do things just because they can

  • @Santhomasito3
    @Santhomasito35 жыл бұрын

    Excellent video. I did this about a decade ago on my 94 Camry - without such an amazing video tutorial. Although it still took about a week of spare moments this time, this video made it 100 times easier. THANK YOU!

  • @rebeccapeel6010
    @rebeccapeel60103 жыл бұрын

    this is why we have professionals working on cars great job

  • @speedkar99

    @speedkar99

    3 жыл бұрын

    Thanks

  • @jaypebbles2431
    @jaypebbles24313 жыл бұрын

    Man, I would pay to watch any video you make. This really is the best “how to” I’ve seen on KZread. Thank you for all of the work you did!

  • @nitinlad1994
    @nitinlad19947 жыл бұрын

    Thanks for the great video on the Toyota Lexus (equivalent to Camry V6 and Avalon). I've successfully changed the timing belts, other engine belts, and water pumps. Your video was very helpful and key source in practical learning about timing belt replacement at my 2000 V6 Camry XLE with 203K miles. Did not hit any hickup; I've just had some delay due to not having stud remove/install tool (had to wait while my car stayed open until the tool arrived). Good to mention that it likely take 2 days for first timer like me. Key reason I decided to repair my car myself is I've get ripped off a few times while trying to service my car from dealer or repair shop. Can not find any reputable/trustable shop in NJ. I would like to encourage your continue putting new auto repair video. Thanks

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    I'm glad my video was helpful for your TB job. I Didn't have to take off the studs because I took off timing cover #3 that covered the water pump housing and it slid straight off. Most of the time those torx on the end of the stud strip or break off.

  • @maxbloom5676
    @maxbloom56767 жыл бұрын

    Just wanted to say thanks for breaking the job down. I'm no master mechanic, so I was nervous messing with the timing belt. You're video was perfect. Not painfully over detailed, just a quick overview of the steps involved. I didn't bother with the cam seals, cuz my Camry has 307K. and I really didn't want to shell out $800 at a shop. parts were only $142, so you SAVED me about $650! Thanks again!

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    +Max Bloom Hey I'm glad the video helped you out. Short and to the point is my style. If the camseals weren't leaking them yea you could skip them. Surprise they aren't at 307k though.

  • @speedkar99
    @speedkar999 жыл бұрын

    @Joe Black Yes same as RX330 with the exception of the tensioner being bolted in horizontally instead of vertically.

  • @speedkar99
    @speedkar999 жыл бұрын

    petersmonkey The highlander is exactly the same, with the small exception of the timing belt tensioner which has two bolts horizontally into the engine instead of vertically like in the video. Do it your self to save labor, if you have a backup car and some time. TB/WP usually run $700-$1000 at shops and dealers including parts. $250 for the parts from RockAuto.

  • @Mike-mf2we
    @Mike-mf2we4 жыл бұрын

    Great video. I really dig your straight to the point style. I was nervous about doing this job and was seriously thinking of taking it to a mechanic to get this done but this video gave me a boost of confidence.

  • @speedkar99

    @speedkar99

    4 жыл бұрын

    Yep I was in the same position a few years ago... hesitant to replace a timing belt. I tried and screwed up (wrong torque settings) on my first car but eventually got this one to work out smoothly.

  • @chrisgutierrez5642
    @chrisgutierrez56427 жыл бұрын

    Omg finally a perfect instructional video! Short and sweet and beautifully edited. And what I mean is no wasted time explaining, no dead air. I've done MANY timing belts and research for future jobs, this is the best.

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    +Chris Gutierrez Thank you, short and to the point is my style.

  • @k0rc
    @k0rc10 жыл бұрын

    One of the very best DIY videos I have seen! It nice you edit out all the unnecessary "watch me back this bolt out 150-turns" or "watch me turn this bolt back in 150-turns"!!! Great job on the video and including the little tips along the way.

  • @speedkar99

    @speedkar99

    10 жыл бұрын

    Thank you for the feedback. Short and simple is my style :)

  • @ItZReDonkulouz
    @ItZReDonkulouz7 жыл бұрын

    I think this is the best video I've ever seen mechanical wise ! because of your good steady! And audio quality

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    +Jim Pelley Thank you

  • @elfocker
    @elfocker7 жыл бұрын

    I must say that your video actually motivated me to do it myself. I was very close to paying someone to do it for me. The detail and quality of your video was excellent. I was just being lazy. But It saved me $250. thanks 👍😎

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    +toyspeed71 Glad it helped.

  • @jae5150voodooyu
    @jae5150voodooyu8 жыл бұрын

    Your videos are filmed, narrated, and edited perfect as far as I'm concerned..no fluff just the facts and I REALLY appreciate you giving the exact size and count of every bolt you pull out. I pretty much had the right pile of tools next to me when I got started. I think this the first ever comment I've given any video on youtube but credit needs to be given here. Timing/water pump/cam seals service is the real deal.. I've done it before on another make/model, but would have taken me 3x longer w/o the specifics of your video. Still trying to figure out how you did it in 14 and a half minutes ;-) Thank you, good work!

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    Thank you very much for your feedback, I appreciate it. My video style is to be straight and to the point, I hate digression. I took roughly 8 hours to do this job including the filming, 4 hours one day and 4 hours the next. I had all the tools on hand, and had one past experience from a previous failed attempt on my Lexus.

  • @Angelo80907
    @Angelo809073 жыл бұрын

    Hands down most detail and informative DIY if seen in years! Thanks

  • @P1ROB
    @P1ROB9 жыл бұрын

    Followed this video step by step and had no problem changing the water pump on my 95 avalon. Much appreciated man. This helped me alot.

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    Thanks, glad my video could help :)

  • @MrRazcob
    @MrRazcob8 жыл бұрын

    Great job !! Thanks for taking the time to make this detailed and clear video. I'll be sure to reference it when I replace my timing belt.

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    +Mike “Mr. Razcob” B Thanks for the feedback :)

  • @davidrhineheimer3300
    @davidrhineheimer33008 жыл бұрын

    Just finished my water pump and timing belt change on my 99 toyota sienna. I bought it for very little because the previous owner did not want to invest between 800-1000 dollars to repair the problem it was having. She did park it as soon as it was having issues though, so the engine had not been damaged in any way and still had plenty of life in it in my opinion. I'm a backyard mechanic, but I'm far more used to motorcycles, scooters, and big old ford trucks. We have a Toyota corolla that's been a trooper, but I really haven't had to work on it too much. I have changed a timing chain driven water pump on a Pontiac before, so I wasn't completely intimidated, though this is a tedious and high risk job. Well, I just finished and I must say that it couldn''t have gone any more smoothly than it did, and I believe that was 90% due to this Terrific Video. This is the best produced and least boring, most straight to the point and accurate repair video I have ever watched. Thank you so much for helping me to get my family a vehicle that we needed for a fraction of the price of what it would have cost if it was in perfect working order!! I saved a bunch on the parts I ordered as well, so I turned a 1000 dollar job into a 150 dollar job! I own the repair manual, and I didn't look at it once...didn't need to. KEEP MAKING REPAIR VIDS PLEASE!! You Rule MAN!!!

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    +David Rhineheimer Thank you very much for your feedback. I'm glad my video helped! My style is to produce videos that are concise and to the point and just present what is important and necessary.

  • @darthgamer6080
    @darthgamer60803 жыл бұрын

    Straight to the point, simple steps, clear instructions, and no stupid intro. Keep it up!

  • @jediknight6187
    @jediknight61878 жыл бұрын

    awesome video dude....you make me feel more comfortable doing the job....I've been working on cars for 15 years but timing belts are probably the only pain in the ass job on a car

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    +Jedi Knight Thank you. All the best on your timing belt job.

  • @MrTurboBiscuit
    @MrTurboBiscuit6 жыл бұрын

    Man just want to give you a shout out. I've done quite a bit automotive-wise, but have never desired to tackle this project on my 97 Avalon. This video was so precise, I only broke out the Chilton manual for torque specs. It's really not a bad process at all, but there are a few things I learned I wanted to share. First of all, if you have a 97 Avalon, DON"T BUY THE TIMKEN CRANK SEAL (224020) on Rockauto! It is too "tall". When fully seated, it sticks out of the hole so much that you cannot seat the timing gear fully back. Timken's website will tell you it will fit you 97, it will not, their measurement says it is .317"! The felpro seal that came out was .25" tall. Just be aware and always compare the old part with the new. I failed to do that this time and got bit. I ended up buying a Lisle 58430 Oil Seal Remover tool. I had all those seals out in seconds. The cam seals were the originals. I also made a crank seal seater from a 1.5" PVC pipe and pipe coupler. Fits perfectly! I used a 1.5" metal pipe nipple for the cams, but the 1.5" PVC pipe may have worked too. Use oil to help seat the seals! I always used oil in the past, but got some bad advice to use white lithium grease and thought I'd try it this time. I'm sure it works for some seal applications, but the grease reacted with the rubber and got sticky! I had a problem removing the water pump, thought I might have to jack my motor up. Turns out the water pump gasket is just thick enough to prevent you from pulling the pump out if they are stuck together. Separated the gasket from the pump and it slid out. An impact wrench really helps with the crankshaft bolts. I waited until the new timing belt was on to torque down the camshaft bolts, I didn't want to risk moving them any without the belt on. Anyway, you saved me 450 in labor, and I appreciate it!

  • @speedkar99

    @speedkar99

    6 жыл бұрын

    +MrTurboBiscuit I'm glad I helped you do the job and saved you money. Thanks!

  • @gltwn

    @gltwn

    5 жыл бұрын

    thanks for the tips

  • @efman2k3
    @efman2k35 жыл бұрын

    Great video. You seem very comfortable and confident. Seems to me you've done this before and have no hesitation doing it again. Awesome work!

  • @speedkar99

    @speedkar99

    5 жыл бұрын

    Yes I've screwed up once before so I knew what to look out for

  • @Minn-Adventure
    @Minn-Adventure9 жыл бұрын

    i have looked at other videos on how to replace water pump on these cars and they made it so complicated thinking i was just going to take it to the shop, but with this video you make it look so easy, GREAT JOB!

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    Thanks. Take your time and have all the tools on hand before starting and everything should go smoothly. Good luck!

  • @garrball1540
    @garrball154010 жыл бұрын

    That was the best tutorial I've watched on this yet! Great Job Thank you so much!!!

  • @speedkar99

    @speedkar99

    10 жыл бұрын

    Thanks :)

  • @DaveCottrell
    @DaveCottrell6 жыл бұрын

    I've watched a lot of DYI videos. This is definitely one of the clearest and best. Well done.

  • @speedkar99

    @speedkar99

    6 жыл бұрын

    +Dave Cottrell thanks glad you enjoy my style

  • @speedkar99
    @speedkar998 жыл бұрын

    @erik3423 I'm not familiar with Subaru engines. Is there a timing belt behind those pulleys? If so it could be a bad idler, tensioner or water pump bearing that should have been changed with the timing belt.

  • @speedkar99
    @speedkar999 жыл бұрын

    Karen Sok You need to use a camshaft holding tool or a 17mm socket to hold the camshaft in its timed position while slipping the belt on. I started on the rear camshaft and used a clip to hold the belt in place against the gear, then worked my way across the idler, front cam, down the water pump, around the crank leaving the slack at the tensioner.

  • @alexmendoza4183

    @alexmendoza4183

    7 жыл бұрын

    HI, in the starter bump method; i have 99 camry; where and how and what do i need to dissconnect so that car dont start??anyone?

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    +Alex Mendoza Just remove the efi fuse or the coil pack connectors on the front of the engine.

  • @alexmendoza4183

    @alexmendoza4183

    7 жыл бұрын

    ok, thanks;;; I have the belt off , putting a new one; i turned the crank to TDC; but cams are not aligned TDC; can i turn cams individually untill they are TDC; does car need to be in neutral?

  • @DavidParker-cf2km

    @DavidParker-cf2km

    6 жыл бұрын

    I could not get the belt onto the crankshaft pulley and align it with the mark on the crankshaft pulley. The following procedure worked for me: Before you even took anything apart you should have pressure washed the entire area where you will be working. Taking care not to blast off labels, useful information, and wiring conduits, pressure wash every thing you can reach in, around, and under the right side of the engine compartment. That caked on oil and dirt you miss is what will invariably later land in your face, in the seals, in the bolt holes, and wherever else it can do the most damage. Jack the front end at least six inches off the ground, put jack stands under the engine frame, remove the right front tire, and pressure wash everything you couldn't reach before. That's what I do first: I do not enjoy working on filthy cars or engines and you either being it to me clean or pay for me to clean it. For everyone else who already has everything apart and is ready simply to install the timing belt (belt), Topside: remove the top idler, put it on the engine cover within easy reach. put the belt on (new ones come with timing marks, figure out which marks are for the camshaft (cam) pulleys and position the new belt accordingly, align the rear belt mark with the rear cam pulley mark, clip the belt to the rear cam pulley at the mark, do the same on the front cam pulley, turn the front cam pulley clockwise and hold tension against the rear cam pulley (the front camshaft will kick to hold tension against the rear cam pulley), Underneath: use the slack to get the belt mark to align with the crankshaft (crank) pulley, clip the belt mark to the crank pulley mark and verify all the belt teeth are engaged on the crank pulley, Topside: put the top idler where you can easily reach it, rotate the front cam pulley counterclockwise to pull belt slack where the top idler goes, and install the top idler. Verify that all three belt marks are exactly aligned with the pulley marks and there is no slack between the front cam pulley and the crank pulley (at least not one tooth of slack). Pull the pin to release the belt tensioner. All three belt marks must perfectly align with the corresponding pulley marks. If not, remove the belt tensioner, reset it in a press, reinsert the pin, reinstall the tensioner, shift the belt to align wherever the belt mark is not aligned with the pulley mark, pull the pin on the belt tensioner and verify that all three belt marks are aligned with the corresponding pulley marks.

  • @Jschwar7
    @Jschwar79 жыл бұрын

    Holy cow that looks like it would take lots of tools, time and patience!!!

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    As long as you plan it, gather all your tools, and label everything it should go smoothly. You can complete this job in a few hours.

  • @aldonavarro2959
    @aldonavarro29599 жыл бұрын

    I am a motor technician, your procedure on the video is really good,you get a lot of videos and you can tell that they are kids playing the mechanics,just two notes,torque on cam and cranck pulley bolts also wheel nuts,apart from that you are a real mechanic.thanks.

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    I'm not a real mechanic.... I just like working on my cars and do the job properly. I've had bad experiences with torque wrenches in the past - if I can get away with it (i.e. not a gasket surface like Water-pump or valve cover) then I just use my calibrated hand :) .

  • @aldonavarro2959

    @aldonavarro2959

    9 жыл бұрын

    torque wrenches come in different sizes, 1/4,3/8,1/2.therefore every bolt has to be torque ,experience is ok when resources are limited or brake down somewhere in the bush, a cranck pulley bolt with the wrong torque specs.could develop a cranckshaft damaged,once the pulley gets a minimum free play the end gets damaged and that means engine disassembly,if it is a Honda new cranckshaft plus color code bearings; wheel nuts not to loose not too tight just right, torque is a professional signature to all your work,please don't get me wrong just a note to make you look even better.thanks.

  • @jonathonfee2542
    @jonathonfee25423 жыл бұрын

    Great video! One tip for others. I couldn't get the crankshaft bolt loose. I used my impact, tried the breaker bar while cranking the engine, even bought a stronger impact. I ended up buying a Lisle 22mm harmonic balancer bolt socket. It has much more mass than a regular impact socket and can impart more force to the bolt. It took a few tries, but it finally got that stubborn bolt loose. They are $26 on Amazon. Well worth the money IMO. Just make sure you have a powerful impact wrench to use with it. I used an earthquake xt maximum torque impact wrench.

  • @realtor411
    @realtor4117 жыл бұрын

    great video. It's interesting to watch a skilled mechanic at work.

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    +oobeach thanks. I'm not a mechanic though.

  • @MarcusSlater
    @MarcusSlater9 жыл бұрын

    This is a very good, thorough how to video.

  • @jimhardie8942
    @jimhardie89425 жыл бұрын

    Why should I buy the official Toyota Service Manual book? When I can just watch your KZread channel. Excellent detail instruction video in less then 15 minutes...

  • @speedkar99

    @speedkar99

    5 жыл бұрын

    The book is a good guide especially for torque specs Goad you learned something

  • @rachelbinto
    @rachelbinto5 жыл бұрын

    Very well done. I have done timing belt on my Subaru and Acura. With the Acura I had to do it over like 4 or 5 times for whatever reason and the 5th time, I had used a clip like you have in the picture to hold the belt to the cams. This spring I'll be doing my Lexus RX, so this video is going to make my life a lot easier. I do not have a cordless impact to break the crankshaft bolt, so Ill probably be using the starter bump method. Glad to see that you endorse this method as well.

  • @speedkar99

    @speedkar99

    5 жыл бұрын

    I'm glad my video can be of help. Thanks

  • @micahgreene4573
    @micahgreene45733 жыл бұрын

    It's not the removal that would scare me. It's the putting it all back together correctly that would scare the crap out of me.

  • @snoman603
    @snoman6036 жыл бұрын

    Great video, thanks for the thorough review. Because of your clear instructions I was able to do this job myself and save about $600. Thanks! ~Ken

  • @speedkar99

    @speedkar99

    6 жыл бұрын

    +Ken Quast I'm glad it helped! Thanks

  • @dbruesch24
    @dbruesch247 жыл бұрын

    best diy video on KZread ever, really great work. didn't overcomplicate anything and great video editing. please keep these awesome videos coming, I'm sure you have already helped many people. 🖒🖒🖒

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    +Daniel B thank you for your feedback, short and to the point is my style :)

  • @lironmtnranch4765
    @lironmtnranch47653 жыл бұрын

    Good job, I replace CVVT units on customers' Volvos all the time but today did my first and probably only Lexus. This video made it a breeze! Thanks much. Great editing, well put together video in a sea of crap DIY content. For example, when I went to change the fuel pump in the tank of my Suburban, KZread was full of videos showing how to cut a giant hole in the floorpan.

  • @aros007z
    @aros007z8 жыл бұрын

    Thank you, you are very skilled at this, wow you make it look Easy....wish I had you skills.... Keep those videos coming. Thanks

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    Thank you

  • @jmurdock36
    @jmurdock3610 жыл бұрын

    That was the best I've seen yet, you are awesome!

  • @friscodeak2895
    @friscodeak28955 жыл бұрын

    At 5:50 minutes you say that the rear cam pulley does not need to come off to change the water pump. On my 2002 Camry LE the two rear bolts for cover #3 are under the pulley. I found this out after removing the belt. Had to stick a 12mm deep socket and ratchet through the spokes of the pulley to slip over the back 10mm bolt to keep the pulley from turning. Then I broke it loose with the cheater bar and 14mm socket. Also, as mentioned in another comment, my alternator has a 3rd jam bolt on the sliding mechanism that needs to be loosened to lower the alternator. Thanks for the fantastic video. It was a life saver.

  • @speedkar99

    @speedkar99

    5 жыл бұрын

    Those two 10mm can be removed thru the sprockets Then timing cover #3 can pivot up around the rear cam

  • @Val-xi4we
    @Val-xi4we2 жыл бұрын

    One of the best if not THE best "how to" videos ever made.

  • @RGMDG
    @RGMDG7 жыл бұрын

    Great Video. Concise and to the point. Easy to understand.. Thank you

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    +Robert Martin Thanks

  • @saintbede60
    @saintbede608 жыл бұрын

    Hey, thanks for the effort, and great editing skills. Please let me know when one of your neighbours homes are for sale!

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    +Bruce Stuart. Thanks. Heh I'm looking for a house for myself around this area too ... :)

  • @derekcasanares4785

    @derekcasanares4785

    7 жыл бұрын

    I'm looking for a house next door too or across the street :)

  • @mikezilly7482
    @mikezilly74822 жыл бұрын

    I watched about six videos in the last 3 hours.. this was by far the most detailed clearly detailed video without an hour worth of commercials and stories that have nothing to do with anything. Thank you! But now that that's all said and done I'm pretty sure I'm just going to sell the vehicle 🤣

  • @austinhydroax
    @austinhydroax5 жыл бұрын

    You really did an outstanding job with this video. Years later its helping me. Appreciate it!

  • @speedkar99

    @speedkar99

    5 жыл бұрын

    Thanks

  • @speedshiftr88
    @speedshiftr889 жыл бұрын

    Nice job...you make it look smooth

  • @GarthGoldberg
    @GarthGoldberg10 жыл бұрын

    Nicely edited, thanks.

  • @SDR_Scooter
    @SDR_Scooter Жыл бұрын

    This was a great video, very helpful for me to change my timing belt and water pump on my 2003 Highlander. The only critique I would give is to add the torque specs. I found a video with them and between this video and that one I got my repair done. Thank you so much!!

  • @borissibiryak
    @borissibiryak3 жыл бұрын

    I watched this video next day I replaced my tbelt and w pump. If I saw it before I made it I would do so many mistakes that took a lot of time. Great video.

  • @speedkar99

    @speedkar99

    3 жыл бұрын

    Glad it helped. Wish I had a guide like this before screwing up my first timing belt job on my Lexus ES330!

  • @FGX318
    @FGX3189 жыл бұрын

    wow !!! crystal clear tutorial, excellent work ! thanks

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    FGX318 Thanks!

  • @iamkasplash
    @iamkasplash8 жыл бұрын

    Great video, thanks! I'll be taking my RX400h to the dealer for this!

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    +Bob Galvan Thanks for the feedback. The RX400h is a bit different in that it uses the 3MZ V6 but doesn't have accessory belts.

  • @edcain3676

    @edcain3676

    5 жыл бұрын

    Is the 04 es330 Very Similar to This, & What's the Recommended Mileage ,Prev.Owner of My 330 Did First T.Belt Change @ 74,350mls.?My Last 01 Toyota Tundra Was Similar in cc,Size ,but Rear Whl.Dr.& it Was 115,000mls.,but ,Of Course this Is Transverse Mtd.Eng .And A VVTI eng.

  • @mkrp4
    @mkrp46 жыл бұрын

    Thanks for the video; did 01 Avalon (belt , idlers and tensioner only) took about 3 hours. I uses 2 inexpensive plastic tipped metal clips to hold T-belt on the cam sprockets. Due to the slack and stiffness of the new belt, it was necessary to advance BOTH cam sprockets 1/2 tooth clockwise to engage belt on the crank pulley at the mark. The installation sequence that worked for me: With tensioner out and belt loosely on the sprockets, align mark on the belt to the mark on the 1-3-5 cam sprocket (firewall) and secure belt to it with spring clip; next, do the same with 2-4-6 (radiator) cam sprocket and lastly do the crank sprocket. If belt looks "too short" during this step, place 17 mm socket wrench on the 2-4-6 sprocket and slowly tun it 1/2 tooth clockwise. Both sprockets will move with the belt, thanks to the clips. After engaging belt with crank sprocket screw the tensioner in while holding the belt on the crank sprocket. Finally, release the tensioner holding pin and remove clips form the cam sprockets. These clips will eliminate frustration caused by belt jumping off the sprocket marks during installation (Sorry, too much medical weed:))

  • @speedkar99

    @speedkar99

    6 жыл бұрын

    +mkrp4 Thanks for your story. Glad the video helped

  • @carnold.knowledge
    @carnold.knowledge2 жыл бұрын

    Excellent video. I have a 2002 Lexus ES300 with a 1MZFE, and this video proved to me, that I will not be doing this work myself. Thank you for this video!

  • @macinmochis
    @macinmochis8 жыл бұрын

    Great job, great video. Thanks!

  • @TaterPS
    @TaterPS4 жыл бұрын

    This is a very good video. Just wished you you would have stressed the importance of actually using a torque wrench on the crank, cams, idler, and tensioner bolts. Keep up the great work.

  • @speedkar99

    @speedkar99

    4 жыл бұрын

    Torque wrench 🤣 I have one built in my arm

  • @jorbitz69
    @jorbitz696 жыл бұрын

    Awesome video speedkar99! Very informative. I am doing my timing belt & water pump and I find your video more straight forward and easy to follow. I have an 04 Toyota Sienna with almost 127K on it; it was first serviced by Longo Penske Toyota here in SoCal at 60K but lately I had been noticing some clear liquids and coolant leaking from under so I decided that it was time for another replacement. Other than that, the minivan is still running great. Thanks!

  • @speedkar99

    @speedkar99

    6 жыл бұрын

    +Jesus Orbita glad you found it helpful, your van will last a while, my dad has a 06 sienna

  • @LittleJimmyNorton
    @LittleJimmyNorton6 жыл бұрын

    I've done 4 cylinder timing belts, water pumps and even head gaskets before, so I do know how to wrench a little, but have been hesitant to do a 6. I paid my buddy last time to do my belt and water pump for $250 (labor) , but I think the $250 will be better in my pocket this time. I have all the tools to do the job and thanks to u and another guy on here. I have all the confidence in the world now to do my 6 cylinder and to make my job even better my buddy has a lift I can use, it beats being outside in 30 degree weather for for 3-4 hours. Thanks for the video!

  • @speedkar99

    @speedkar99

    6 жыл бұрын

    +LittleJimmyNorton Glad the video helped and encouraged you to tackle the v6. It's not as easy as the 4 banger but it's not difficult either.

  • @LittleJimmyNorton

    @LittleJimmyNorton

    6 жыл бұрын

    Just a little more time and patience. Just curious, how long did it take u? Whatever it took u, I can probably ad an hour to mine, at least. Will also give u an update after I do the job in a couple days.

  • @geoffmiller3468
    @geoffmiller34684 жыл бұрын

    THANKS DUDE YOU BOUT TO SAVE ME UPWARDS OF $600 DOLLARS!!

  • @speedkar99

    @speedkar99

    4 жыл бұрын

    Whoa! Share the savings 😉

  • @MrFireman164
    @MrFireman1649 жыл бұрын

    Great video , thanks for taking the time :)

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    Thanks

  • @grahamcrooks3581
    @grahamcrooks35813 жыл бұрын

    Good Stuff, and thanks. Nice to see the photography is clear, [the view on the actual job is obscured] and good watch points. Beware when releasing the two 14mm headed long bolts into the upper engine mount that they're stretched tight. You need a good six point socket or you'll burr the heads.

  • @bioreef01
    @bioreef019 жыл бұрын

    Hello. Thanks for this very informative DIY video. (I also followed your valve cover gasket replacement video to do my valve covers). I started out wanting to just install the Aisin TKT-024 kit, cam/crank seals,ignition wire and plugs, front brake pads and rotor, and front struts on my 2000 Camry with ~245,000 miles. But I ended up doing those plus valves cover gaskets, thermostat, and radiator hoses. I really appreciated paint can opener tool trick. I was able to remove the cam seal for cylinders 1,3,5 pretty easily with only that tool. But for the other cam seal, because there wasn’t enough space to work with, I first inserted the paint can opener into position. Then I put one end of a length of ½” conduit against the opener handle. Finally, I used a hammer and with a couple of hard taps, the seal came right off. (Not sure though if there would be enough room for this method without removing the fuel injection plenum.) A bonus is that the paint can opener tool didn’t put a scratch on the cam shaft. For the crank seal, I used 2 paint can openers and a gear puller. I actually worked nicely. Here is a link to pictures: drive.google.com/folderview?id=0Bxgs7wi0I7SbN0pIMkU1QmNHVWM&usp=sharing Hope it helps.

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    Thanks for the reply. I like your paint can opener method with the conduit, I wish I could have used that trick when I was doing the rear cam seal, but I wasn't doing the valve cover gasket at the same time so I'm not sure if it would have cleared the plenum. Thanks for the idea though, good thinking :)

  • @cchiofalo
    @cchiofalo9 жыл бұрын

    fantastic video, thank you

  • @CluelessEngineer
    @CluelessEngineer10 жыл бұрын

    pvc pipe? Do you have a tool for everything.

  • @atilahun2354
    @atilahun23548 жыл бұрын

    Excellent video presentation - one of the. Good that you mentioned the size of the sockets as you went along and showed skill on getting off. Good job!

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    +Atila Hun Thank you

  • @tr8086
    @tr80864 жыл бұрын

    2020 You hold the Belt with the Best Car Repair Videos!!!Saved me Serious $$$$$ Thank You and Happy Newyear my friend!

  • @speedkar99

    @speedkar99

    4 жыл бұрын

    Thanks and I'm glad you find it useful

  • @subwayguy1610
    @subwayguy16107 жыл бұрын

    Great video, sir!

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    Thanks

  • @CZUNIGA36
    @CZUNIGA365 жыл бұрын

    Great job. I needed this video. Don't pay attention on negative comments.....this awesome. .03-10-2019

  • @speedkar99

    @speedkar99

    5 жыл бұрын

    Glad it helped

  • @dadefope80
    @dadefope809 жыл бұрын

    You make it look sooo easy. Great job on describing every step in detail. Great picture.

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    Thanks. It is not that hard if you look at it closely.

  • @JSWMobileMedia
    @JSWMobileMedia6 жыл бұрын

    Wow! Great video! This is exactly what I needed. Thanks for taking your time to include the detailed explanations on how to get all this taken apart/put back together. Awesome! SUBSCRIBED!

  • @JSWMobileMedia

    @JSWMobileMedia

    6 жыл бұрын

    Question on the brake caliper housing....did you paint those? Powder coat? Or did you buy them already done?

  • @mr.desert7384
    @mr.desert73848 жыл бұрын

    forget this ill take it to the shop

  • @DragonPirates

    @DragonPirates

    7 жыл бұрын

    LOOL

  • @beefen7921

    @beefen7921

    7 жыл бұрын

    lmfao!

  • @simpsonsimpson3071

    @simpsonsimpson3071

    6 жыл бұрын

    yup even though this is a good video but not step by step detailed process... thats what i am used to for this complicated work.

  • @jonathanlitz2018

    @jonathanlitz2018

    5 жыл бұрын

    Mr. Desert it would be less expensive if you do it yourself

  • @muckinyoface

    @muckinyoface

    5 жыл бұрын

    Not if he never gets it back together or apart for that matter....

  • @princedabby8414
    @princedabby84149 жыл бұрын

    in short i gave u 100% good work

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    Thanks

  • @rayoliver1101
    @rayoliver11013 жыл бұрын

    50 YEARS UNDER MY BELT TURNIN WRENCHES,GOOD VIDEO YOUNG MAN,DONT FORGET YOUR MARKS ,ALWAYS REPLACE CAM SEALS,ALWAYS BUY THE BEST TIMING BELT,DAYCO,GATES,HENLY,ETC

  • @stephencrowfoot244
    @stephencrowfoot2445 жыл бұрын

    This is why changing timimg belt/water pump/front oil seals etc., on front wheel drive transverse engine cars is expensive, a lot of dissasembly needed just to get access, excellent video and commentary. (I drive a 1990 Volvo 240 and this job is a doddle on my car by comparison!) Thank you for your excellent series.

  • @speedkar99

    @speedkar99

    5 жыл бұрын

    Thanks. The disassembly is regardless of engine for this job

  • @meedily
    @meedily9 жыл бұрын

    Christ. No wonder why they charged me $450 labor plus the parts. Money WELL spent.

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    $450 sounds about right for labor.

  • @JWBrussee
    @JWBrussee8 жыл бұрын

    Hey, where did you buy your camshaft holding tool?

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    Princess auto (harbor freight equivalent in Canada)

  • @2000willsome
    @2000willsome4 жыл бұрын

    You are my hero. You explained it so clearly without taking long to do it. Thanks very much for going to the trouble.

  • @speedkar99

    @speedkar99

    4 жыл бұрын

    You are welcome!

  • @TocyBlox
    @TocyBlox3 ай бұрын

    And this is a 1000 job at Lexus 😢. My mom took it there in 2019. She never maintained the car other than oil changes. Now I have the car and been doing all the maintenance myself. 😊

  • @speedkar99

    @speedkar99

    3 ай бұрын

    Good move. Much cheaper and you'll learn about the car.

  • @ff5gus
    @ff5gus10 жыл бұрын

    Come to the USA and do my 2003 Lexus es300

  • @NzelumChukwuebuka
    @NzelumChukwuebuka8 жыл бұрын

    +speedkar99 pls never be offended. what is the name of that 90deg air tool used to loosen the bolts down there, can i get the amazon link? Thanks you doing a great job!

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    +Nzelum Chukwuebuka Air ratchet.

  • @cw4933
    @cw49334 жыл бұрын

    Perfect video, complete & to the point. even a pro could watch this without losing his mind. Great work tnx! Keep it up!

  • @speedkar99

    @speedkar99

    4 жыл бұрын

    Thanks I'm glad you appreciate my video

  • @mooseboy84
    @mooseboy849 жыл бұрын

    I just want to say thanks for this video. I changed my timing belt about 4-5 years ago and it ended up taking me 3 days! It could have been hours if I had seen this video first! One thing I would note is that when removing the water pump, the STUDS in there have an inverted torx or something like that on them and can easily round off. I rounded one of them off and needed a STUD REMOVER to get it out. Also, when installing the studs, you should put a bit of thread sealer (white paste, not loctite) so the coolant doesnt leak from studs. One other thing I recall is when I put on my new timing belt, for the LIFE of me I could not get the marks to all line up on the new belt. It was always about 1 or 2h teeth off, and would not all 3 line up. Long story short after wasting about 4 hours trying everything, I finally read on one of the Toyota nation forums as long as the belt is properly seated and NOT skipping any teeth, then disregard the lines. So after wasting half a day I went back out there, lined everything up and made sure it was seated properly and just ignored it. It ran fine after that...

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    mooseboy84 Thanks for the feedback. Removing the waterpump studs are a pain and that's why I opted to remove the cam gears and timing cover #3 instead. The teeth alignment aren't dead accurate, but shouldn't be a whole tooth off. It depends on the angle that you're looking at the belt and mark when aligning. Perhaps your cam and crank marks were mixed up or the belt was backwards.

  • @brainstorm4207
    @brainstorm42077 жыл бұрын

    its a cam shaft sprocket not a cam shaft!!!! youre driving me crazy

  • @speedkar99

    @speedkar99

    7 жыл бұрын

    +BrainStorm4207 agreed.

  • @spliff08
    @spliff088 жыл бұрын

    5:21 hahahahaha

  • @gianfrancoa
    @gianfrancoa9 жыл бұрын

    I'm new to this channel and found that these vids are really good and well edited.Good work.!!

  • @speedkar99

    @speedkar99

    9 жыл бұрын

    gianfrancoa Thank you for the feedback!

  • @torreystalk5809
    @torreystalk58094 жыл бұрын

    Has to be one of the best part replacement videos I've ever seen!

  • @speedkar99

    @speedkar99

    4 жыл бұрын

    Awesome

  • @EP1CNELSON
    @EP1CNELSON6 жыл бұрын

    Changing the water pump is a bunch of bull from toyota.

  • @speedkar99

    @speedkar99

    6 жыл бұрын

    +EP1CNELSON True because the timing belt is in front of it.

  • @EP1CNELSON

    @EP1CNELSON

    6 жыл бұрын

    speedkar99 There is just so much to do, I had to help my friend because he couldn't afford to pay 1000 dollars to all the gauging mechanic shops to get it done.

  • @jamesrairdon5550
    @jamesrairdon55508 жыл бұрын

    Excellent video, there are camshaft seal removal/installation tools that make the job much easier and almost foolproof removing and installing the camshaft seals. They work nice in tight places.

  • @speedkar99

    @speedkar99

    8 жыл бұрын

    +James Rairdon Thanks. The camshaft removal tool I got was too big to fit in the back seal, so the paint can opener had to make do. As for installing, next time I'll try using the old seal and camshaft sprocket to push in the new seal as I tighten the camshaft bolt.

  • @malcolmprebble6350
    @malcolmprebble63503 жыл бұрын

    A simply outstanding guide to this important job, thank you.

  • @pimpinpenz
    @pimpinpenz3 жыл бұрын

    Replacing this today on my moms car, The aisin kit is really good. Also good to see another Canadian for once!

  • @tonyscalifornia
    @tonyscalifornia Жыл бұрын

    You’re the best diy auto repair chanel. Learning to fix my own car by watching your video 10x lol

  • @speedkar99

    @speedkar99

    Жыл бұрын

    Thanks. Make sure you watch my teardown videos to learn how to break things too haha!

  • @jimdandy6472
    @jimdandy64726 жыл бұрын

    I also make auto repair videos, so I know how much work it takes to get the great shots that you did, get the light right, edit it down, etc. This is a great video with a steady camera, great detail, but not too much, and good comments. Thanks for all your work.

Келесі