Nothing better than finishing a job the first time with good results. The hardest part of most jobs is taking the risk into the unknown.

@1RoadGarage

Жыл бұрын

Yep. Felt good. Thanks 👍

@rab3137

Жыл бұрын

@@1RoadGarage my grandfather was an old farmer. He always said if a man built it you can repair it. Pay attention to how it comes apart and you'll know how it goes back together. Last but not least never start with the most expensive repair first. People always think this is a disaster and will be so expensive. Often it's a simple fix start small work your way up. Thanks for posting quality videos.

@1RoadGarage

Жыл бұрын

@@rab3137 I like that, “if a man built it, you can repair it”. I’m gonna remember that one. Thanks for the tips.

@freemanfornow264

Жыл бұрын

@@rab3137 yes that is something I've always lived.....I constantly say and tell my children, if somebody else can do it, there's no reason I can't do it and do it better.... the main thing is not being afraid to try

@mariodiy4517

Жыл бұрын

Reminds me of my first timing belt job on my 2005 Pilot. Same, took me 2-3 days to put together in December of 2021. I had to tackle my intake manifold to change injectors. I was less nervous about it. Great job!

Jimmy. I've been repairing & rebuilding cars for almost 60 years, and I got to say you did a great job. Not only completing the job, but also giving a great play by play description on how to do it. Great job !!!

@1RoadGarage

Жыл бұрын

Thank you for that. 🤙

@laurentpenot2656

Жыл бұрын

sure ! he really has a great teacher approach 👏🏻👍🏻

Doing your own repairs is an excellent idea, because it enables rapidly amassing a varied collection of spare parts for future repairs.

You have faced your fear and come out victorious in the end. Congratulations !!!!

I've done so many of those I could do them in 30 minutes. It's best to just sit your intake onto the gaskets and start some bolts (don't tighten them all the way) so you can look and see how much glue you need. It will vary especially in cases of gasket changes, machining or block being decked.

25 years ago I had a coolant leak on my 1995 , it was only a couple years old and I was in a pinch. I removed it, cleaned it and put it back together without gaskets just using Permatex Right Stuff. I only barely snugged the bolts up then let it cure for 24hrs. Then I torqued according to spec, haven't had any leaks or grief since and am well over 300k

You did an excellent fantastic job from disassembly to labeling, to cleaning, to taking your time, to photographing, to reassembly. You r truly a perfectionist!

Just like many other seasoned veterans I'll also say good job. Don't worry about how long it takes you, the end result is what counts & you did a fantastic job. It's better to go at a comfortable pace & do it right the FIRST time rather than rush things & end up having to do it all over again. Looks like you keep things clean & organized, that right there does wonders for any job. It does pay off to label everything even if you think you know exactly where it all goes. Sometimes unforeseen circumstances cause you to take a break in the middle of the job & that's when labeling & documenting it all really pays off. The camera on your phone is a great tool to use in doing that. Pictures are worth a thousand words.

In fact it's not really necessary to put the crank at TDC firing #1 if you don't move the crank during your repair. It is only necessary to make the mark for the distributor position and the two rotor positions. Note though that on many engines the oil pump is turned via a drive rod that fits into the bottom end of the distributor drive gear. if you have gotten the distributor in correctly but it's not seating all the way into its hole then the pump shaft may have turned a bit. In this case once the distributor is in you'll need to turn the crank a bit to get the distributor end to line up with the pump shaft, the distributor will then fall into place. RTV isn't necessarily a big problem if a little of it falls into the engine, it's soft and it will simply get chewed up in the oil pump gears. Just don't get a big glob in there that could block or plug up some oil passage. Otherwise, very nice job.

@Floyd12345

9 күн бұрын

I'm burning coolant out my tail pipes and loosing coolant with no leaks. 1995 gmc 350.

The money saved is well worth it ! GOOD JOB ! Pictures also help out with replacement

Excellent job Jimmy! Been waiting to see this one. I've replaced the fuel injection Spyder on my '97 Suburban and that plastic plenum was painful. I wanted to do the whole intake but that distributor process had me nervous, so I never did. My '99 K2500 Suburban has the tiniest leak right in front where that gasket maker is poking out and I really want to do this job before heading out overlanding. Your video has given me the courage to try it as soon as my arm (rotator cuff surgery) is healed up. Thanks for sharing. Glad to see you back doing mechanic stuff again!

if your going to replace the cap and rotor, you can drill a hole thru the cap into the rotor with an 1/8 drill bit for and alignment hole. Then just mark the distributer base where it contacts the block and it will be perfect.

You did a great job explaining why and showing us where. Just an incredible job of being so thorough. Keep up the great work. A lot of people can benefit from this video.

Awesome! Highfive dude. Fixin to tackle my 91 v2500 suburban.. watching this has helped clarify the unknown a bit for me aswell. Ive been following your videos and appreciate the time you put into these videos. Ive been through hell and back with my suburban though definitley wouldnt trade it or sell it for anything at this point. Been a sacrafice and learning curve that has changed my life. Its tough enough to find clear concise information for the DIYer so your videos really make a huge difference for some of us here on the tube. Thanks jimmy! Kudos and Keep on truckin!

I'm in the process of doing all this now..... waiting right now for new camshaft and lifters to come in...... I've never done anything beyond changing oil, plugs, rebuilding tbi, small tune up stuff like that..... I'm scared to death that it won't run when I get it back together but I have confidence in my work (at least I keep telling myself that lol).... Thanks for the video and if you wanna see my solution to oil cooler lines leaking, I posted a video......I think it's the best possible solution, at least it's better than anything I've seen yet... KEEP UP THE GOOD WORK!!

@freemanfornow264

Жыл бұрын

By the way, I have been on this for a month now, replacing ALL grounds, power steering pump, starter, intake gasket, valve covers, camshaft, etc etc..... thank God I work for myself and can take the time off or it would take me a year🤣🤣

Been troubleshooting a high idle of my 5.7 350 Chevy G20 for a month now. I've replaced a ton of sensors, valves, and gaskets w no luck. I used your videos several times especially w removing and rebuilding the throttle body. Only thing i can think of now is that i have a vacuum leak at the intake manifold and need to replace the gaskets. This video is top notch. You really go all in w every detail and i can't thank you enough for making these videos so thoroughly. Not sure yet if i'll do this myself or take the van somewhere... it's honestly nerve racking both ways as i just don't just shops to actually do a good job no matter where i take it.. i've had so many bad experiences. So might end up just attempting this myself. Anyway, thanks for the excellent play by play you're a real champ for this.

I did that exact job on the side of the road in a school bus , took 4 hours... It's been 4 years and still going strong

Oh my god, that thing is so clean and rust-free, must be a dream to work on!

Jimmy, with that die grinder to clean the intake manifold, thou that disc did work, 1 small slip could spell disaster. I highly recommend the 3M roloc bristle disc's, they are a plastic abrasive gasket cleaner. The attach right to the die grinder, and have 3 different "grits" green, yellow and white, the white one is a 120 grit that is great on aluminum. I use them almost everyday doing valve covers, diff covers and head gaskets in my engine shop. I highly recommend checking th out.

Man, I recall the first time I put the distributor back in my 350. The notch for the oil pump moved a little and had me stumped for a while. 😂

@1RoadGarage

Жыл бұрын

I was hoping that wouldn’t happen to me. 👍

Nice Job Jimmy! It's good to see you back wrenching on your vehicles!

@1RoadGarage

Жыл бұрын

It definitely feels good to be working. 👍

I have a carbide edged scrapers that works miracles. They are called Super Scrapers. Well worth the money. Also I use thread sealant on the manifold bolts, the bosses are open in the valley so oil can seep through and up the threads of the bolts.

You should have used pipe sealant on the corner bolts due to the holes going into the coolant passage.

Good job man I'd rather see man take his time rather than have to redo later. About do one myself. Ty

Hey Jimmy, I got a 98’ Z71 with 225K miles on it now and I have had to do this twice. The 1st time I had a mechanic do it at around 120K and he explained that those 98’ 350s gaskets were notorious for going out around 100K because GM got some that were paper thin in places. At 215K, my father-in-law and I tackled it again because the gasket and gasket maker failed so bad the truck was acting like it had a vacuum leak! That was a full 10hr Saturday!

@1RoadGarage

Жыл бұрын

Nice. Pretty sure if I had to do it again and didn’t have to film the process, 10 hrs seems about right. 👍 The hardest part of the job is scraping the old gasket.

@scottbarrett4753

Жыл бұрын

I have done my 98 twice, it is painful. I upgraded the fuel injector spider as well.

Perfect timing for this video as I have to do this on my 1988 Chevy Silverado. I’ll be installing a new distributor and coil when I reinstall the intake manifold.

Try 3M 18730 discs for cleaning cast and aluminum. No sanding grit being slung into the engine. GM came out with a bulletin saying not to use the sanding discs anymore. Just a thiught

@1RoadGarage

Жыл бұрын

Good to know, thanks!

Great job. I have done this same job on a 1985 460 Ford engine. Process was almost identical. It takes time to do it right for sure. I took two days to do mine.

Jimmy, looks like you did a very thorough job in replacing the intake manifold gasket. Something you don’t want to rush.

amazing attention to detail. Im a mechanic for a living and would welcome someone like you to work on my own vehicle.....as long as Im not paying hourly. lol

great camera work. very good demonstration. i like that wild little crowfoot you used!

@1RoadGarage

Жыл бұрын

Harbor Freight for that one. Good tool. 👍

Helluva job my friend. I deleted the egr because of all the gunk I found in my manifold. I thought it might run differently but I can’t tell any difference. Again, I was impressed with your thoughtfulness of your work!

@scotteric8711

Жыл бұрын

You will only notice the egr in temperature extremes. (Really hot or really cold) The problem is created because the factory ecm accounts for a reduction in combustion temps that aren't there. Long term, you may get lower Long term Fuel Trims and maybe a CEL.

at least 10 years or so ago, Holley had a larger 670CFM replacement throttle body available. There was an Edelbrock dual-plane intake with larger throttle body ports as well. Those were worthy upgrades on these TBI engines...did it in my chevy van!

You are right but it's worth it and it's coming out perfect I'm almost ready to put it back I appreciate your video I've gained a lot of knowledge

Great job explaining the whole job

@1RoadGarage

Жыл бұрын

Did my best, thanks. 👍

I had to do this on my TDI. You are very careful and document it well. However, I think a good engine degrease and thorough pressure wash prior would have made part of this much easier.

MAN I love watching you do stuff! The problem is it motivates me to do stuff too. Then I spend all day in the garage and the wife gets crankier. HAHA! Thanks Jimmy!

Job well done man don’t worry you did a good job keep on trucking

@1RoadGarage

Жыл бұрын

Thanks! 👍

I like how you took your time and marked everything on the distributor, a friend of mine had a similar suburban to yours and he had to replace the engine,when he put his distributor back he was off exactly 180 degrees.

@1RoadGarage

Жыл бұрын

What does that do exactly? Did it ruin anything or just not start?

@thatsonebadhatharry8610

Жыл бұрын

@@1RoadGarage it won't ruin anything it just won't start. One thing you didn't have to do was to set the engine at TDC. It doesn't matter where the distributor is when you pull it out AS LONG AS YOU MARK IT WHERE IT IS BEFORE YOU REMOVE IT (the capps were not meant as shouting but just to stress that you can do this just by marking the beginning and ending points of the rotor button. The only time you need to do what you did is if you had rotated the engine after you had removed the distributor. Other than that you did an excellent job as you always do.

@cavemanjoe79

Жыл бұрын

@@1RoadGarage it ran rough on start up and backfired, then my friend’s dad flopped the distributor 180 degrees and it fired right up. Fortunately no noticeable damage from the few seconds it ran.

@1RoadGarage

Жыл бұрын

@@thatsonebadhatharry8610 I was wondering about that. If I simplify popped out that distributor and did the job and put it back in exactly as it was, how would the truck know any difference? Maybe it’s a default safety thing? 🤷‍♂️

@bryandraughn9830

Жыл бұрын

​@@1RoadGarage They start at top dead center if you just want to figure out where everything goes. Once you have the piston topped off during the compression stroke, then you know where to point your rotor. At #1. Then you use the timing light to position the rotor to the cap in the precise location that it requires to run properly. It's not nearly as complicated as it seems at first but if you visualize everything that's moving, and why, it makes sense in a pretty straightforward way.

Nice work. You make me miss my old Chevelle sm block.

I never imaginedtakingsll that apart. 'm proud of you.

@1RoadGarage

Жыл бұрын

Haha, thanks!

Good job ! The oil pump drive sometimes rotates after dist. removal . Can move it back with a blade screw driver .

Looks like you did a excellent job! Next should be the valve cover gaskets.

Nice work Jimmy!

Just for information, all BOSCH distributors have a factory made mark indicating where the centre of the rotor arm should be for cylinder 1 at top dead centre, its a small groove line on the top of the distributor body right under the cap, this mark used with the crankshaft timing marks can be used for static timing the ignition

Jimmy I did my upper and lower gasket replacement and power washing the intakes and cleaning the top part of the engine all in 13 hrs here at my apartment 98 Ford E250 van 4.2 liter V6 Essex engine

I did my first head gasket n intake gasket job on tbi motor a few years ago. Had hard time with getting timing correct even marked it lol easy motor to learn on👍

@1RoadGarage

Жыл бұрын

The timing scared me but it worked out thankfully.

The gaskets that come with the FelPro 98000 set are far superior. They are aluminum with bonded rubber. The only problem is that you can only get them as part of that set, so they cost a bit more; however, it is well worth the investment as they will not fail as others do. It's all I use on SBC jobs. The 98000 is for Vortech intakes, but they also make one for the non-vortech intake.

Looks good. I dropped my steering wheel and pulled my dash out to replace a heater coor. That's also a lot of time.

Great job... always slow doing something on a vehicle/motor.....still wanted you to do a meet-n-greet. I'm in Memphis and followed you for years now... would love to hangout with you on Broad Street or camping somewhere...thank you for all you do....

As a fellow '95 Chevy Truck owner, I will be performing the exact same procedure. As an auto mechanic for more than 22 years I can tell you that you did a great job. You have earned your first stripe. Thanks and take care.

Outstanding job

@1RoadGarage

Жыл бұрын

Glad you enjoyed! 🤙

Great Job! C1500 Suburban here!

@1RoadGarage

Жыл бұрын

Nice man!

wow great vid Jimmy, that's what Im talking about

@1RoadGarage

Жыл бұрын

Glad you liked it! 👍

I replaced my factory plastic distributer while i was at it - thats another winner

Side note tip, ame intl quick valve change tool.Engine Restore for good compression.

Great Job Brother 👏 👍

I'm going to have to do this soon I think. I have a GM 3800 Series 2, still using the orange coolant. Most of it is new as I lost a lot when I replaced the 2 plastic coolant elbows and again when I just replaced the water pump. I had to add a lot after replacing that. When I end up having to do the upper and lower intake gaskets I will flush it all out and put the regular green stuff in it.

@railroaded1991

Жыл бұрын

If it runs the orange stuff from the factory it's probably not a good idea to change to another type. Coolants have different formulas for different engines. Make sure before you change, that green has the proper formulation for your engine.

Just a tip be careful with those scotch brite wheels. I know you said you were, but they can definitely eat away at aluminum fast like you said. They also deposit abrasives, so never use them on head and block mating surfaces where those abrasives can get into the crank case.

You done good, congrats.

You probably could have used a carbide scraper for the gasket removal. Amazon has quite a few. Nice job!

Great job! Would’ve been a good time to throw an aftermarket Edelbrock on there, though, with a bigger throttlebody for more horsepower!

Imagine the labor to access the intake manifold. My Taurus was so simple it was an 06. This engineering and planning had no thought of maintenance imo.

I've pulled the distributors out of a 1965 f250 and a 1977 f250. Both times I was extremely negligent. I didn't do anything other than unbolt and yank them. When I went to install the new one, on the 77, I had to jump on the internet and look up the firing order with distributor diagram, and I plopped the new distributor in vaguely where I thought I remember it pointing and hooked up plug wires according to internet diagram. It ran perfectly. On the 65, same thing except that my memory of the distributor orientation was faulty, and it wouldn't run. I simply loosened the bolt, lifted the distibutor, rotated, dropped it back in. Did this a few times, till I found the correct position, judging by the fact that it either didn't fire up, or ran horribly, then it ran perfectly. I will say that in those scenarios, the distributor is at the front of the engine, easily accessible, and one can just stand there and navel gaze without breaking a sweat. The other thing is, if I had to do it over again, I would definitely mark everything. Because why not? In your scenario, marking everything was wise.

Nice job. The only things I would have done differently would be cleaning the engine thoroughly, and replacing the valve cover gaskets before starting. My thinking is if I'm going through all of the hassle of replacing the intake manifold gasket, I'm going all the way and stopping any potential oil leaks from the valve covers too. On a side note, count me as someone who thinks that you probably skimped with the RTV sealant on the China walls. Whenever I watch the pros on other channels, including Engine Power, they always apply a thick bead, probably twice as thick as the bead you laid down. Anyhow I hope it lasts and wish you luck. Keep up the good work.

@Mike-xt2ot

4 ай бұрын

I agree. That's going to leak oil in the near future and now will be able to redo in half the time. Good job other than that

Funny how all these videos use Fel Pro gaskets for the intake manifold on these trucks. Before I started I emailed Fel Pro they said do not use our gaskets we don’t make proper gaskets for those years of trucks, then pull out the back rear ports you’ll notice the little pinhole in the Fel Pro gaskets. The OEM gaskets are the correct ones to use for this truck.

Great Job!!!

You can also do a final wipe with acetone before applying rtv.

@alanmerritt860

Жыл бұрын

Little late now. It's all done

The way you marked the distributor makes it a no Brainer , good job. I use the toyota rtv , I think it's the best you can buy.1/4 inch bead works perfect. Great video brother.

One thing I want to make you aware of these engines are pretty much bullet proof they're well built but make sure you change the rod and main bearings the reason is that that's there major fail when they do fail. It's not very common but does happen anytime I buy a used Chevy truck that's the first thing I do not cause it needs it but parts do wear over time and this will keep you from having catastrophic failure and the parts aren't expensive the job is pretty easy to. Also while you're there go ahead and replace the oil pump too there's nothing better than knowing you'll have no major issues that could cause you too spend a lot of money

Just for the future, if you drench those cast intakes in LAs totally awesome, scrub it with a toothbrush, and rinse with hot water it will pull most of the oil and grime out of the cast and come out looking almost brand new

Doing this on a TBI motor would be a vacation lol I had to do head gaskets on a 97' Tahoe with a Vortec and just getting to where the intake was removed was irritating. Re-assembly was even worse.

Nothing like those "elephant in the room" repairs that start as a mild concern but you know very well you're going to have to address before it becomes a major problem. Anyone who's been forced to deal with the dreaded o-ring replacement on the oil pump pickup in the early 2000's GM full-size 4WD will know EXACTLY what I'm talking about.

Did that job a few times, you'll be fine. It will leak most likely, after a year or so. Good luck

Ya did that lots of times that's a long time ha learn as you go and fill comfortable with

I think you did a fine, meticulous job.

Looks like you did a good job. My only advice would be careful about using the sanding discs they almost all contain aluminum oxide which can embed and damage engine bearings. Some will also leave the surface too course which can literally scrub off the gasket with thermal expansion over time. Secondly the only silicone I will use anymore is permatex right stuff 1 minute gasket maker. Trust me I’ve used it thousands of times. Lastly I’m a little more on the generous with the silicone and make sure to get it in the corners below and on top of the gasket.

@rexfaktor2898

Жыл бұрын

Long ago, GM published a bulletin about the discs. The debris (disc and gasket and carbon) get thrown everywhere and can have a negative effect on engine bearing life, and can compromise flatness in some scenarios. The manifold I like to surface with a fine sanding block before getting it clean enough to eat off of. Cleaning the heads is the tedious part... The grey silicone (Yamabond and friends) is what most manufacturers use now...I use that or what is available. Toyota's black sealant is really nice too. Chevy's like to wick oil up the intake bolts...best to put a little white Permatex thread sealant on them... Agreeing with you and adding my 2 cents...

Jimmy is a wonderful person. 😊 I wonder if he was named after the GMC Jimmy? 😮

i had to spray guide coat over the alum manifold intake ports and sand it to get the manifold flat so it would seal. my intake gasket sagged down into the engine producing a massive vac leak - my had would stick to the oil filler tube under the vacuum! Idle was at 1500rpm with that leak.

cleaning the manifold (both half's) took all day. The rtv, i like to cut a v shaped grove in the tip and lay the bead that way - sort of like doing a windshield

@1RoadGarage

Жыл бұрын

Right?? Those gaskets are the worst!!

Good work. A confidence builder

Your local mechanic is not going to be as detailed and/or as concerned. Good job overall. I’m surprised you didn’t do the valve cover gaskets as you were already in there.

Did my 93, this job is a giant pain getting everything clean and reinstalled correctly

Curious if you were getting a check engine light from the EGR system before doing this job, and be curious if it has gone away. I expect when I finally do this job on my 95 with 200k+ miles that I will be pulling A LOT more junk out of the EGR passages.

Nice job.

Attention to detail!! Also, super handsome guy.❤

Hi Jimmy When it comes to a liquid gasket maker like silicone sealant the fine line is have I put enough on or have I put too much on. The rule of thumb in the olden days before 1996 electronics is one third of the flange width is the maximum width of the sealant to be put down the minimum amount of sealant is one quarter of the width of the flange. Nower day's it is between 2mm and 6mm of sealant depending on manufacturers specifications like the vehicle manufacturers says 3mm but the manufacturers of the silicone says 5mm so first attempt you go with vehicle spec it starts to leak, then you try the silicone spec it is too much, so 3rd try in between let's try 4mm it dose the trick. The vehicle manufacturers silicone is of a denser mix than the after market ones, plus the factory gunk always splurges out they are never a clean look so they don't care on how much is put on just is it sealed. But most of all Jimmy very good, clean work you are showing the not so friendly mechanic's to shame in how to do the job correctly and cleanly.

@1RoadGarage

Жыл бұрын

Thank you for your comment. I agree with you, during my ‘research’ I found many different ways of doing it. Ultimately came down to what I thought was the correct method but of course second guessed myself once it was done. I don’t know why those two areas can’t have a rubberized pre-made gasket that we can set into place though??

Frequently never realized Protip - every connector on the harness is unique and will only mate with their counterpart. I'm also aware this is not a 100% universal truth but close enough that it doesn't matter

I have seen those sanding disks destroy engine bearings. I haven't used them on internal surfaces for years.

did you get any engine lights due to timing being off? was timing set perfectly with your marks?

Yes sir. It’s that easy 👍

I like tearing apart all the cars that I buy, its like a puzzle but giant xD

Great video. Your neighbours must be able to hear you yelling a block away 😉. I have to turn your videos way down. This looks a lot more involved than the one on my '99 6.0L. My son has a '95 K1500 4x4 with 330,000kms on it, but I'm not sure that we'll tackle this unless needed...😁

Before you take anything apart, take out your cell phone and take several pictures. Try to get 2 angles of every disconnect, hose routing, anything that looks "busy". Lots of busy under Jimmy's air filter. Most of the time it is NOT necessary to label connectors. There is almost always enough difference in them and were they lay that getting them mixed up is not the problem, it's getting the routing right going back together...PICTURES. I'm not telling novices not to label connectors though. If you do, make sure to remove them when you are done so you don't have a gooey mess to clean up 2 weeks later.

Wrong coolant, get you 4 -5 gallons of that green 50/50 mix. I've also done head gaskets on a 305 tbi before (kind of the same as 350 tbi ) fairly easy.

👍 good job

Is there a detail issue turning the motor back off top dead center or just as is restart?

02 sonoma V6 my truck will crank over try to start then when I let off the key it just chugs a couple of times and dies I jave alreadey replaced my fuel pump and was going good for two weeks . Is this my intake gasket going bad .?

I have a 92 4.3 thats getting gas in the oil dipstick. is just gas, I'm thinking is either the fuel injectors or the head gaskets.

Just did this today took about 7 hours 😭 (mostly cause I forgot where a lot of the plugs and bolts went)