Something to consider with age of your boat. Make sure your Mercathode system is functioning properly. First make sure you are getting 12V to your Mercathode. If that's OK next is to check how many milliamps it's putting out. You will need a special probe and multi meter. Mercathode System Testing: When the boat is in the water, disconnect the orange wire that comes from the anode at the mercathode controller. Set the digital reader to show milliamps. Connect the black meter lead to the terminal on the controller. Connect the red meter lead to the end of orange wire. See what range its reading. Depending on the reading you may find that you need a new unit. My boat is on its second one in 23 years and last year it was reading on the low end normal. Mechanics will replace it this Spring. If you don't have the extra "puck" electrodes added to the transom on either side of the transom assembly. Highly recommended especially in you keep your bost in the water. Make sure all bonding straps are attached and in good condition.

@KeysBoatingChannel

Жыл бұрын

Hi Mark! Super GREAT Information! Thanks so much! Hope you & Family are doing Great! This is the first time in the 18 years I owned this boat that this is happening. Thanks Bro! Peace!

Boat work NEVER stops. I have to handed to you my brother, you are always on top of things when it comes to your boat maintenance. Great video. ❤️❤️❤️

@KeysBoatingChannel

Жыл бұрын

Always thank you my Brother! Yes, its a never ending project....But I Love It! Lol...Blessings! Peace!

Guys, it is extremely important that the areas are carefully fresh water washed to remove all the chlorides before you paint. Furthermore, using a wire brush is okay to remove some of the peeling paint, but prior to painting, you need to use a coarse sandpaper in order you make an anchor pattern in the substrate for the paint to have a good adhesion. When priming it could be a good idea to use an epoxy primer before you apply the finish paint. Remember to respect the minimum over-coating intervals between each coat and of course the minimum immersion time after final coat.

@KeysBoatingChannel

23 күн бұрын

Thanks for watching our video! Great detailed information! 👌 Peace from the Keys!

Love, this boat are work . Glad your showing this very good to know

@KeysBoatingChannel

Жыл бұрын

Thanks Bro! Greetings to you and family! Yes Bro, love my boat but she always needs a lot of attention...lol. Peace!

Great job 🏝🏝🌴🌴💥💥💯🔥👌🏽

@KeysBoatingChannel

Жыл бұрын

Thanks, Bro! Blessings! Peace!

Hello! I noticed that you're using a steel brush to remove corrosion and old paint from your outdrive. I just wanted to point out that outdrives are typically made of aluminum, and using a steel brush on aluminum surfaces can be risky. It can lead to scratches and an increased risk of corrosion. I would recommend using a softer brush, sandpaper designed for aluminum, or chemical degreasers that are safe for aluminum instead. Thanks for the video, and I hope this tip is helpful!

@KeysBoatingChannel

9 ай бұрын

Hi, thanks so much for watching our video. Great information to know. Thanks for the comment. Peace from the Keys.

I noticed the quality job taping off the power tilt rods. I just got my outdrive painted by a "professional" who spraypainted the rods... i thought this is no good to do as it puts wear on the gaskets. Am i correct? (they also painted my stainless steel duo-props) =(

@KeysBoatingChannel

2 ай бұрын

Hi, I put the tape on because to me its only logical that paint on the ram rods can cause some problems in the future to seals, and that paint inside mixed with the hydraulic fluid can't be good either. I'm not an expert, but Its just a little prevention just in case. I would not paint the props, I like the stainless steel look on them. Thanks for watching our videos! Peace from the Keys!

@tyrel7185

16 күн бұрын

Idiots! That paint can clog the valves, and flakes can cause seals to leak both internally and externally.

Reinforce your ground

@KeysBoatingChannel

Жыл бұрын

Yes, thanks! Only found one ground on the outdrive loose, the other one is attached. Thank you for your comment & watching! Peace!

So…it has been a year. Did it hold up better this time?? Inquiring minds want to know…

@KeysBoatingChannel

5 ай бұрын

Hi! this it did a little better than last time. The more we can remove the old paint and clean it, it gets better. Thanks for watching! Peace from the Keys!