When you pointed the camera in the box it put a big smile on my face. Can't wait to see it fitted. Good work Jay.
@FriscoBoatersGarage13 жыл бұрын
@Sxwraith3490 I will keep making them as long as you guys like watching.
@Sxwraith349013 жыл бұрын
I believe I've watched just about every video you've made over the past month; Now that I have finished this one (your latest), I'm kind of down, knowing that whenever I wanted to, I could just pop on a video of yours that I hadn't seen before and just rock'n roll through them all. I pay for satellite tv every month, and I prefer watching your videos over my own tv believe it or not. From the Glastron, life updates, jetski's, and now the 220, it's been a blast! Keep it up, you're almost done!
@Sxwraith349013 жыл бұрын
Actually, I haven't refreshed your page for a while because I've been adding all your vids to my playlist; I just refreshed the page, lo and behold, I found two more! I'm excited!
@aaroncrossland73985 жыл бұрын
Looks good Jay
@FriscoBoatersGarage13 жыл бұрын
Good question. We will find out when it is installed.
@FriscoBoatersGarage12 жыл бұрын
@2chefjeff2 The hardener is the trick. It makes the paint dry faster and harder. You mix it together and then let it sit for 30 minutes and then spray. Rattle cans take forever to dry, and are not as tough. I use the etching primer from duplicolor.
@joe100808 жыл бұрын
How has it held up to the test of time? Its been about 5 years at this point. Great videos man helping us out alot
@josepeixoto33845 жыл бұрын
LOTS of great ideas,man; the drive stand, and the way you suspend it from the crane(WATCH out for those long threaded rods!!), but i use 1/4 inch bolts only,the drive only weighs 43 kg, if you put the chains (dog chain is enough for that, no need for that heavy chain --but i see you have money to burn,lol) on the other side, it will balance better,obviously; and the painting ;(if you sand thru the primer you should alodine first,the manual says)
@FriscoBoatersGarage13 жыл бұрын
@kc8ard Yes, that is true, but they do not sell zinc Di-chrimate. That is the good stuff
@FabianCharrua2 жыл бұрын
Love all your videos!! I've been seeing that you dont put etching primer over paint because it can actually lift it and cause corrosion. That you're supposed to use it only on bare metal and then put normal paint primer everywhere before final coat. Any thoughts or results you can share? Thanks!
@mmoorryy200213 жыл бұрын
you can see most of the water will flow out of the leg, you will get a small amount of water come out of the sides, you can see the spray in the video you mentioned(searay 220 corsa) but i agree, it sounds awesome.....
@Bluebark64FIS Жыл бұрын
With the hardener, you really are shooting epoxy paint...hard as nails when cured. Would like to know how much the pain flowed, if any, over the next day.Never thought of hitting Tractor Supply for paint...lol. Going to now...redoing my gimble bearings/bellows (and whatever else I find) so might as well shoot the drive! Thanks a good job!
@SeaRay45DB10 жыл бұрын
I love your video's! Now that it's been several years since you used the Valspar, are you still a big fan or have you found something better? Getting ready to paint my 1989 Cobalt that I have restored, finally at the end! If it was 2 feet bigger, I would put the Corsa exhaust in, but at 21 feet, its a little small. Don't know how long I will keep it.
@kc8ard13 жыл бұрын
I forget which vid it was where you mentioned zinc chromate, but you can still get it. Aircraft Spruce sells it. Btw, I'm about to embark on the same project myself with a Sea Ray SRV 190. I made the same mistake when I bought it.
@alsationwolfdogs10 жыл бұрын
Rustoleum high performance paint is a good choice as well
@reelsalt91794 жыл бұрын
I painted my outdrive and painted the surfaces that the zink sits on and now I'm reading that the zink needs to sit on bare metal to work properly
@streamersonfire4 ай бұрын
That product you used implement paint is no longer available anywhere. What would you recommend to use today?
@dwetick111 жыл бұрын
Black epoxy spray paint is the best that I have used on the outdrive. Mask off all the zincs first. And by the way, cutoff that trim indicator wiring as it is degrading all the wiring in your boat by galvanic corrosion!
@jonwallace7015
2 жыл бұрын
D wetick I have just bought a boat and the indicator has been cut .I was going to replace it .I never thought about what you are saying but it make sense.
@FriscoBoatersGarage11 жыл бұрын
That works too.
@FriscoBoatersGarage13 жыл бұрын
@cb900steve Makes it all worth while to have a little bling after all this.
@FriscoBoatersGarage12 жыл бұрын
I ordered it direct from Corsa, and I think it was around !800
@eviloctober9 жыл бұрын
I am about to do the same for mine kinda new to the boating frisojarretts videos are AWSOME I refer to them often! hes the reason i even attempt to try any of these things on my own thinking of going with the OEM part number 802878Q1 which is the phantom black
@blackrandomapple10 жыл бұрын
Hi, where did you get the side exit exhaust? Looks like a awesome idea... wanna do it on my bayliner 185? Do you have any videos of the boat running with the exhausts fitted? Cheers
@themguys1j8
7 жыл бұрын
HAHAHAHAHAHA 18" BAYLINER WITH A FUCKING SIDE EXHAUST OMG HJAHAHAHAHAHAHAHAHAHA
@deepfriedmeatpie13 жыл бұрын
wiil water come out of the exhaust with the flaps open because it will go down through the leg
@dwetick111 жыл бұрын
I use black spray epoxy $4.47/ can...very tough stuff!
@splash5974
5 жыл бұрын
Where do you purchase this?
@ttlkamd7 жыл бұрын
Can you be more clear about product used? Especially for self etching primer??
@edwardmiller529611 жыл бұрын
350 merc mag mpi bravo 3 seapump impeller motor is in boat
@markdimaio83968 жыл бұрын
Rust-Oleum epoxy hi-gloss automotive paint?
@FriscoBoatersGarage
8 жыл бұрын
+mark dimaio Farm Implement
@markdimaio8396
8 жыл бұрын
OK thanks.
@markdimaio8396
8 жыл бұрын
+FriscoBoater Can I bush paint it ?
@FriscoBoatersGarage12 жыл бұрын
@PedroCalil1 corsaperformance
@zoki2222ify8 жыл бұрын
is this 2c paint?
@FriscoBoatersGarage
8 жыл бұрын
+Zoran Perovic Technically yes... You can add the hardener to this paint to get it to dry faster and be very drurable
@zoki2222ify
8 жыл бұрын
+FriscoBoater but you use car paint 1c?and put hardener
@louieaceti1508
8 жыл бұрын
+FriscoBoater How long does it need to cure before it can go back in the water?
@S.Womack3467 жыл бұрын
Lol!
@marklockwood80312 жыл бұрын
INSTEAD OF REPLACEING THE WHOLE LOWER UNIT WHY NOT NOT JUST REPLACE THE GUTS OF IT?
@S.Womack3467 жыл бұрын
dude, you talk soooooo much! lol
@Future_memory
7 жыл бұрын
Shane Womack its the adderall 😂
@blackrandomapple10 жыл бұрын
Hi, where did you get the side exit exhaust? Looks like a awesome idea... wanna do it on my bayliner 185? Do you have any videos of the boat running with the exhausts fitted? Cheers
@Jacksonjames4
10 жыл бұрын
a 18' bayliner with side exhaust? cant be more than a 4 or 6 cyl..that wouldn't sound good
@themguys1j8
7 жыл бұрын
HAHAHAHA A FUCKING BAYLINER WITH A SIDE EXHAUST HAHAHAHAHAHA
@themguys1j8
7 жыл бұрын
ARE YOU FUCKING KIDDING ME A BAYLINER???????????? SIDE EXHAUST? HAHAHAHAHAHAAHH BAYLINER IS ONE OF THE WORST BOATS MADE
Пікірлер: 49
When you pointed the camera in the box it put a big smile on my face. Can't wait to see it fitted. Good work Jay.
@Sxwraith3490 I will keep making them as long as you guys like watching.
I believe I've watched just about every video you've made over the past month; Now that I have finished this one (your latest), I'm kind of down, knowing that whenever I wanted to, I could just pop on a video of yours that I hadn't seen before and just rock'n roll through them all. I pay for satellite tv every month, and I prefer watching your videos over my own tv believe it or not. From the Glastron, life updates, jetski's, and now the 220, it's been a blast! Keep it up, you're almost done!
Actually, I haven't refreshed your page for a while because I've been adding all your vids to my playlist; I just refreshed the page, lo and behold, I found two more! I'm excited!
Looks good Jay
Good question. We will find out when it is installed.
@2chefjeff2 The hardener is the trick. It makes the paint dry faster and harder. You mix it together and then let it sit for 30 minutes and then spray. Rattle cans take forever to dry, and are not as tough. I use the etching primer from duplicolor.
How has it held up to the test of time? Its been about 5 years at this point. Great videos man helping us out alot
LOTS of great ideas,man; the drive stand, and the way you suspend it from the crane(WATCH out for those long threaded rods!!), but i use 1/4 inch bolts only,the drive only weighs 43 kg, if you put the chains (dog chain is enough for that, no need for that heavy chain --but i see you have money to burn,lol) on the other side, it will balance better,obviously; and the painting ;(if you sand thru the primer you should alodine first,the manual says)
@kc8ard Yes, that is true, but they do not sell zinc Di-chrimate. That is the good stuff
Love all your videos!! I've been seeing that you dont put etching primer over paint because it can actually lift it and cause corrosion. That you're supposed to use it only on bare metal and then put normal paint primer everywhere before final coat. Any thoughts or results you can share? Thanks!
you can see most of the water will flow out of the leg, you will get a small amount of water come out of the sides, you can see the spray in the video you mentioned(searay 220 corsa) but i agree, it sounds awesome.....
With the hardener, you really are shooting epoxy paint...hard as nails when cured. Would like to know how much the pain flowed, if any, over the next day.Never thought of hitting Tractor Supply for paint...lol. Going to now...redoing my gimble bearings/bellows (and whatever else I find) so might as well shoot the drive! Thanks a good job!
I love your video's! Now that it's been several years since you used the Valspar, are you still a big fan or have you found something better? Getting ready to paint my 1989 Cobalt that I have restored, finally at the end! If it was 2 feet bigger, I would put the Corsa exhaust in, but at 21 feet, its a little small. Don't know how long I will keep it.
I forget which vid it was where you mentioned zinc chromate, but you can still get it. Aircraft Spruce sells it. Btw, I'm about to embark on the same project myself with a Sea Ray SRV 190. I made the same mistake when I bought it.
Rustoleum high performance paint is a good choice as well
I painted my outdrive and painted the surfaces that the zink sits on and now I'm reading that the zink needs to sit on bare metal to work properly
That product you used implement paint is no longer available anywhere. What would you recommend to use today?
Black epoxy spray paint is the best that I have used on the outdrive. Mask off all the zincs first. And by the way, cutoff that trim indicator wiring as it is degrading all the wiring in your boat by galvanic corrosion!
@jonwallace7015
2 жыл бұрын
D wetick I have just bought a boat and the indicator has been cut .I was going to replace it .I never thought about what you are saying but it make sense.
That works too.
@cb900steve Makes it all worth while to have a little bling after all this.
I ordered it direct from Corsa, and I think it was around !800
I am about to do the same for mine kinda new to the boating frisojarretts videos are AWSOME I refer to them often! hes the reason i even attempt to try any of these things on my own thinking of going with the OEM part number 802878Q1 which is the phantom black
Hi, where did you get the side exit exhaust? Looks like a awesome idea... wanna do it on my bayliner 185? Do you have any videos of the boat running with the exhausts fitted? Cheers
@themguys1j8
7 жыл бұрын
HAHAHAHAHAHA 18" BAYLINER WITH A FUCKING SIDE EXHAUST OMG HJAHAHAHAHAHAHAHAHAHA
wiil water come out of the exhaust with the flaps open because it will go down through the leg
I use black spray epoxy $4.47/ can...very tough stuff!
@splash5974
5 жыл бұрын
Where do you purchase this?
Can you be more clear about product used? Especially for self etching primer??
350 merc mag mpi bravo 3 seapump impeller motor is in boat
Rust-Oleum epoxy hi-gloss automotive paint?
@FriscoBoatersGarage
8 жыл бұрын
+mark dimaio Farm Implement
@markdimaio8396
8 жыл бұрын
OK thanks.
@markdimaio8396
8 жыл бұрын
+FriscoBoater Can I bush paint it ?
@PedroCalil1 corsaperformance
is this 2c paint?
@FriscoBoatersGarage
8 жыл бұрын
+Zoran Perovic Technically yes... You can add the hardener to this paint to get it to dry faster and be very drurable
@zoki2222ify
8 жыл бұрын
+FriscoBoater but you use car paint 1c?and put hardener
@louieaceti1508
8 жыл бұрын
+FriscoBoater How long does it need to cure before it can go back in the water?
Lol!
INSTEAD OF REPLACEING THE WHOLE LOWER UNIT WHY NOT NOT JUST REPLACE THE GUTS OF IT?
dude, you talk soooooo much! lol
@Future_memory
7 жыл бұрын
Shane Womack its the adderall 😂
Hi, where did you get the side exit exhaust? Looks like a awesome idea... wanna do it on my bayliner 185? Do you have any videos of the boat running with the exhausts fitted? Cheers
@Jacksonjames4
10 жыл бұрын
a 18' bayliner with side exhaust? cant be more than a 4 or 6 cyl..that wouldn't sound good
@themguys1j8
7 жыл бұрын
HAHAHAHA A FUCKING BAYLINER WITH A SIDE EXHAUST HAHAHAHAHAHA
@themguys1j8
7 жыл бұрын
ARE YOU FUCKING KIDDING ME A BAYLINER???????????? SIDE EXHAUST? HAHAHAHAHAHAAHH BAYLINER IS ONE OF THE WORST BOATS MADE
@Ante_Knezevic
7 жыл бұрын
It's the best for the money paid.