Am I the only one that hits the thumbs up button before the video even starts?...my go to guy for knowledge and performance!

@Chasemanuti

2 жыл бұрын

I just did it 😂!!

@robvan1584

2 жыл бұрын

Do not care if he is schooling us from a Dodge, Ford or Chevy I have my seat.

@mikerecords5530

2 жыл бұрын

I do it too

@strawhatgarage2517

2 жыл бұрын

I do the same thing

@davidmiller4594

2 жыл бұрын

I'm actually terrible at remembering to like videos. Thanks for the reminder 👍

Just got my Gt45 junkyard 5.3 up and running, its an absolute BLAST on only 8lbs for now. Thanks for the motivation Richard!

@micahbuchheit1283

2 жыл бұрын

That's Awesome!!

@carlylemcafee5483

2 жыл бұрын

Nice! Where did you buy your gt45 from?

@JohnnyAnderson1

2 жыл бұрын

@@carlylemcafee5483 ebay, just make sure you find a seller with good feedback of course

@julesp.5801

2 жыл бұрын

How much power is it making on 8lbs? I wanna build a turbo junkyard 5.4 aswell

@JohnnyAnderson1

2 жыл бұрын

@@julesp.5801 not sure, should be close to 600 fly wheel

Remember for you budget guy there are some great junkyard/ budget oem injectors, some Volvos use 41 lbs injectors and bigger, 8.1 have a little bigger injectors, you can decap some stock truck injectors, a friend of mine is running 2 junkyard fuel pumps and decapped Volvo injectors, most 1/2 hard line some spots are still 3/8s and is making close to 700

@youngbuckrefrigeration716

Жыл бұрын

Do he have videos of doing that 😳?

@turkeyboyjh1

Жыл бұрын

@@youngbuckrefrigeration716 I’m not sure but sloppy mechanics has a video on deccaping stock injectors to gain about 100% fuel flow, the idea is you get 2 good sets of injectors decap them all and then send them out to get Them flow matched

Before anyone asks, same applies to your 6.0 and 5.3

@micahbuchheit1283

2 жыл бұрын

Lol. Thanks for clearing that up for some folks.

@LSX_GORILLA

Жыл бұрын

Thank you 😂

I didn’t realize you are only 5 hours from me!!! Some day I need to stop by when I’m down that way and buy you a cup of coffee!!! You have helped me so much!!!

I’d love to see 4.8, 5.3 and 6.0 graphs with identical cam and turbo layed out next to each other. It would be an obvious illustration of what displacement is doing on the same setup.

@richardholdener1727

2 жыл бұрын

PLEASE SEE THE VIDEO WHERE I COMPARED THE STOCK 4.8L, 5.3L AND 6.0L

GREAT VIDEO RICHARD. CHEAP HORSEPOWER IS THE FOCUS. GREAT VIDEO AND THANKS FOR SHARING. SOMETHING TO CONSIDER.

Thank you, everytime, thank you!

Boost is your friend...and even more boost is your best friend...

You should revisit this with a true divided hotside to show the improved boost response.

thanks for answering questions even in the first 2 minutes, I also loved all your old articles in muscle mustangs and fast Fords! Is the new 7.3 gas motor something to be excited about?

@richardholdener1727

2 жыл бұрын

YES

Awesome video's

Hey Richard could we do a dyno result test on the old school cool cans. May I on fuel injected and carbed, ice vs dry ice. I seen allot of conflicting information on this topic. Btw ur vids are the best!

Hi, hope all is well. Video idea. Compare the BTR truck Norris cam…. With the NSR Truck Norris cam…but don’t upgrade the springs on the NSR cam…. Also maybe compare other NSR cams w stock springs.

Good shit Richard

I love the fox mustang I might have to switch to chey

That's my exact setup in my 68 c10

Boost makes everything better

Decap stock injectors and they flow 72ish lbs at 58psi base. Can run a small amount on E85 or a pretty decent amount on pump gas that way.

@richardholdener1727

2 жыл бұрын

as long as they all flow the same

Are you going to continue to use the sloppy best cam for testing or was that a one and done situation?

What about oil pumps ?? Looking into the melling high volume one .

On all of your cam and boost LS vids, are you still running factory pushrods and rockers?

# 1👍🏻! 💪🏻

Fairly new to watching your videos, would higher compression make a drastic power difference? Bacially doing same setup on a 6L but running at 10.3:1 comp?

@chaskacox-potter3217

2 жыл бұрын

Yeah, it's gonna make more power with more compression. Adding boost is the equivalent of adding more compression, so you will need less boost to get the same output as the guy with less compeession

I probably missed the video? Hot sizes house size! Haven't seen any video of same set ups over different sizes hot side. 1.32 etc

@richardholdener1727

Жыл бұрын

I'VE DONE AR TESTING WAY BACK

C+S+B...Got it!

@richardholdener1727

2 жыл бұрын

seems simple, right?

@deanstevenson6527

2 жыл бұрын

@@richardholdener1727 When you say it. I learn H+C+I from you. heads, Cam Intake. This one is Far better...less Expensive! More Power...Thanks Richard...

Please do the same video but with hemi 5.7 sub 2009 non vvt

@richardholdener1727

2 жыл бұрын

please see the hemi turbo vids

How long does that carry over 7k rpm

Id like to see this same test with the same engine setup but with different brand turbos. Say what are the results with an ebay gt45, on3 gt45 and such. How the quality of the turbo plays a factor in the boost level vs the power and torque. "Cheap turbo makes 10 psi @ 5500 rpm vs higher end turbo makes 10 psi @ 2000 rpms" Also do it with ball bearing vs journal bearing. ($100 vs $500 vs $2000 turbo) is the "you get what you pay for" worth it... you see alot of twin gt35s and gt45s in the LS community but is it really worth it to go cheaper or spend the extra few hundred for the name brand and size it better to the setup say a 76/75 vs the gt45.

@richardholdener1727

2 жыл бұрын

you will see very little difference at 10 psi

@single_cam_coyote

2 жыл бұрын

@@richardholdener1727 I was just saying 10 psi as a reference. Basically what are the results with a higher end turbo vs cheap and bb vs journal bearing. If you put a manual boost controller on it how quick do they "light up" at the set psi and how effective is the power and torque curve. In a nut shell what to small of a turbo would do and what an over sized turbo would do to the setup.

@francisbeaudry8598

11 ай бұрын

r@@richardholdener1727 rick for the BTR stage to cam do you need more valve clerence and for the spring any machining or juste fit ,,,,,,tanks for all your time ,,,merci bien

Now when talking about a junkyard 4.8 and putting gap on rings with forged pistons. Are you using the stock connecting rods and all stock bearings? Or is this a rebuild with the honed bores, new bearings new timing and so on. Just curious if the testing was just throwing a few pistons and cam in and bolting on a turbo then sending it to outer space

@richardholdener1727

6 ай бұрын

we run turbos on stock motors with stock pistons, rod, crank and block with just added ring gap. Also with forged internals

@satoshibautista7766

6 ай бұрын

Thank you

What would you do for fuel; in a boosted situation, if e85 isn’t in your area? The closest e85 pump for me is 2 hours away.

@richardholdener1727

2 жыл бұрын

run 91 with less timing

Just curious, does switching to e85 hurt the seals and gaskets? 👍👍

@brucebeamer2298

2 жыл бұрын

On the last pod cast you mentioned about long/short tube runners. Any videos you did on maximizing them or videos out there I can watch?

Would you recommend dual springs with a stock cam and boost?

@richardholdener1727

2 жыл бұрын

no-beehives will work

.... Would running ethanol free gasoline, E90 around here, gain or decrease power outputs? 🤔

@YourMom-ll6ku

2 жыл бұрын

U mean e10? Regular pump gas

Test 2v heads Vs 4v heads on the same block

@richardholdener1727

2 жыл бұрын

and intake and cams-they will all be different

Thank u for all your research 🔬 love the Chanel. Can u guide me in the right Direction to build 800HP on my Mercury marine 1999 454 mpi mag I already have a M-1 pro charger pushing 5psi. What cam and valve springs would help me accomplish 800?

@richardholdener1727

2 жыл бұрын

YOU WILL NED MORE THAN A CAM

@scherzer25

2 жыл бұрын

@@richardholdener1727 I forgot to add that my pro charger has a water inner cooler. I believe I have the upgraded injectors and fuel pump as well. I was wondering if I could get close to 800 with some head work and beehive valve springs and Cam and maybe change the police so I am making 7 pounds of boost 🤔

Hey Richard, I am starting a build, it currently has a low mileage 4.8L. I ultimately just want a nasty little street truck, but i also have a l92 and 6l80 that i was thinking on swapping but both engine and tranny will need to be rebuilt because its higher mileage. Any recommendations? I think 600hp at the wheels would be a reasonable goal for street use, but would want the ability to crank it up if needs be.

@richardholdener1727

8 ай бұрын

turbo and 600 whp is easy

@jeffery6649

8 ай бұрын

if you had the choice between the 4.8 and 6.2, which one would you choose ?

@richardholdener1727

8 ай бұрын

a 6.2l would be aluminum and bigger so I would pick that if the price is the same (usually not the case), but most would pick the cheapest route to make an easy 600 hp (that would be the 4.8L or 5.3l)

Maybe i missed it but was the comp mentioned?

@richardholdener1727

2 жыл бұрын

9.8:1

What about exhaust valves ? There is a superalloy exhaust valve for virtually everything now .and with girthy valve springs ,comes elevated oil tempature at least in the marine app's. Street guys don't talk about as much though

the description is missing the "add ring gap" disclaimer

@Dauntless.steadfast.fortitude

Жыл бұрын

.007-.008 ring gap per 1 inch of bore per Sir Cam alot or .028 on 4 inch bore

@ZoeyR86

Жыл бұрын

@@Dauntless.steadfast.fortitude I gap cast piston at 7tho per inch forged at 8.5 tho per inch also make the a bit extra especially for 26xx and the stronger more ductile pistons have higher expansion ratios this is way they get a lot of slap when cold. But if doing a ls junk yard boost build just air for 28-38 tho (5.3 to 6.2). And it will do fine you will hit the rod limits before they get pinched but maybe add another 4-5tho if not properly cooling charge air.

Any fuel pump recommendations for a 4.8 with 1000cc injectors?

@richardholdener1727

Ай бұрын

what power level?

@Ray4rmDade305

Ай бұрын

@@richardholdener1727 twin 62mm turbos, tsp stage 3 cam and dual spring kit, Holley 1000cc injectors Everything else completely stock(motor,trans etc.) Going for a daily street truck 550-700whp

6.0 LS p/u looking for turbo for towing power, what I need to do

@richardholdener1727

Жыл бұрын

FOR TOWING-JUST ADD BOOST

What push rods did you use? Stock 7.4?

@richardholdener1727

Жыл бұрын

we measure and adjust

Are 1000 cc snake eaters injectors good for 1000 hp on e 85 on a turbo 5.3

@richardholdener1727

2 жыл бұрын

YES

@curtiskitchens2233

2 жыл бұрын

@@richardholdener1727 thanks buddy

Let's get down to business

How was the soccer game?

@richardholdener1727

2 жыл бұрын

not the hoped for outcome!

What kind of timing were you running under boost?

@richardholdener1727

2 жыл бұрын

22

@turbomeo1863

2 жыл бұрын

@@richardholdener1727 how much world that be with 91 for example? Was that at the 12psi run?

Are u using Holley software?

@richardholdener1727

Жыл бұрын

HOLLEY HP OR DOM

And ring gap

Wonder if anyone has used a thumper cam with boost

@ramirodiaz4545

2 жыл бұрын

Every cam is a turbo cam.

👍🏽🇺🇸👍🏽

Why e85? The normal guy is on 91-93 gas. All you do is e85 or race gas.

@richardholdener1727

2 жыл бұрын

use the fuel you like

What happened to the video? 12 minutes?!

Personally I blame squirrels

@springer383

2 жыл бұрын

hahahahahahahahahahahahahahahahahahahahahahahahahahahahahahahahah omg hahahahahaha man thats the line of the century.. man you got some mileage out of this one.what a side splitter..family has to be proud

Hmm, that's weird, my bone stock Coyote mustang makes way more 🤔