excellent video! thank you for sharing!

You should get a set of brass punches, jewelers hammer, and a mini vice. The vice can be used to squeeze the pins in. For padding attach 2 strips of leather or similar on the vice jaws.

Very innovative, great job, thx for sharing

The underwear piece for hazmat suit batman is definitely the best one for Batman

Great custom info! Your peg change outs (cuts and reinforced with nails) were awesome news to me! Really learned a lot from your vid. Leg redo worked great also! I would recommend a wired cape addition to fully rock out this amazing Batman you did. He is all kinds of badass! Great job!

@loopercustoms

Жыл бұрын

Thanks! Yeah I have switched out capes on another Batman I had and they make the figure look way better I will probably swap this one out soon.

Awesome

I liked everything but the thin thighs on the Arkham Batman so I swapped the thighs out. The lower legs I kept and the knee joint cut matches up perfectly.

Nice work man

The skinny head on Arkham Bats just throws me off. But man you did a good job on the custom

Looks great. Good job

Some just swap the entire legs and arms to make it taller. They say it's easier that way

as for the 8:50 you can just use a piece of paper u put it in the cup, and then it makes the joint tighter without having to super glue. Also, for 18:16 you can put the pin in the knee, and then peg each side of the leg just as you did when you disassembled it. it will be a little easier.

@asylumpatient96

8 ай бұрын

Yea i was just thinking abt the easier way of putting the knee joint,just got my three jokers batman,cant wait to customize my AC batman.

As soon as I got my arkham batman I dont care for the game design so I switched out the arms for the same 3 jokers arms. I just took out the caps so they’d fit and put the deaths metal head on him cus I prefer short ears batman over long ears. He gives off Hush vibes now and will be my be all batman till I get the new blue hush batman that just got revealed. Great work tho👌

@loopercustoms

Жыл бұрын

Yeah I am a big fan of the long ears so as soon as I saw this I knew I would make this switch.

You wanna do the thighs and the eyes and the boots if your looking for more of the Arkham game accuracy

Instead of cutting and glueing the arm pegs, is it possible to heat up those shoulders, pry out those peg pieces, and exchanging them?

@loopercustoms

Жыл бұрын

The pegs are connected with a joint going through so I think you could either cut one side and just pull it out or drill through the shoulder and it would just slip out. Here is a video about how to do a Marvel Legends one but I think it would work the same way: kzread.info/dash/bejne/maGHrLSqdM3Ohco.html

The only thing that threw me off on this figure he doesn't have pupils. Just white eyes. The Arkham Asylum figure has pupils for sure. So does the Arkham Knight figure.

Correct me if I'm wrong but couldn't you have just removed the bicep swivel and switched the shoulders?

@loopercustoms

Жыл бұрын

Yes, that would have probably been easier but I did not like the shoulders on the Arkham Batman.

@jamesknight3022

Жыл бұрын

@@loopercustoms still very good work!

How long should I put my figure in hot water for?

@loopercustoms

Жыл бұрын

Like 30 seconds to a minute. Depends on how hot you get the water I would just pull it out every 30 seconds and see if it is loose yet.

@fluffylildingo

Жыл бұрын

@@loopercustoms thx for letting me know!

would you sell this figure?

Do You think you could just switch the biceps

@loopercustoms

Жыл бұрын

The Arkham Batman arm is single jointed while the 3 jokers Batman is double jointed so I don’t think so.

@bigbootymen938

Жыл бұрын

@@loopercustoms I mean like pop the arm from the bicep swivel and switch them

@loopercustoms

Жыл бұрын

@@bigbootymen938 Yeah that would probably work! Just switching the shoulders over you wouldn't have to do any mods.

@bigbootymen938

Жыл бұрын

@@loopercustoms okay I'll try it out then thanks for the advice

Um I can't say that a reuse of the very first batman mold that's also inaccurate to the source material is the best batman so far. Year 2 is my favorite Todd has done

@loopercustoms

Жыл бұрын

The year 2 is a good one but it is just a reuse of the 3 Jokers Batman which in my opinion is a little to tall and the chest is a little to small so I did this Kitbash to make a good black/grey Batman