Thank you so much for your video. It's super helpful and whilst I'm excited to install my AL 3H I'm also a tad nervous.

Brother thank you for this vid

@RebuildEverything

2 жыл бұрын

No problem! hope it helped!

@JohnJacobJose

2 жыл бұрын

Where did u get the bracket from??

That's pretty sick, dude! I would do more mods if I could do them myself, but unfortunately, labor is quite expensive here in Northern California! Keep safe!

@RebuildEverything

2 жыл бұрын

Thanks man! The good thing is the car still amazing without any mods

Was your bag really close to your strut? For the rear.

Hey bud, just fitted my system and am pending to run calibration. Quick question, did you stumble across airlift faults such as: mount calibration and invalid mount? I've installed the manifold as per recommended and have swapped out the manifold twice with a new one. Was wondering if its because I haven't run calibration. Grateful if you could let me know.

@RebuildEverything

2 жыл бұрын

No I didn’t run into that issue at all. The only issue I ran into was a sensor height issue during the calibration mode. Once I adjusted the arm everything was fine. I would recommend running the calibration mode if you haven’t already. It should help you identify any issues.

@euroworksbrunei7025

2 жыл бұрын

@@RebuildEverything I am thankful and grateful for your reply mate... Was such a noob mistake as I didn't run calibration at the time, so yes stupid me. Did you get the annoying knocking noise in the rear top mount? How did you resolve that or is that something we just have to live with. 😂

Does it eat up the tires fast?

I've done a ton of research and still cant find what the Ride Height sensors actually do or what they are for. You would think with what this system cost all that info would be provided. I'm leaning towards 3p System.

@RebuildEverything

Жыл бұрын

Ya the information out there is pretty vague. There's more info in the instruction manual than I found online about the height sensors. I don't really know there purpose other than maybe sending some info to the controller to help adjust air pressure

One year later how have these held up have you had any problems at all I am thinking about putting them on my Supra. Thank you in advance

@RebuildEverything

Жыл бұрын

No issues at all! I did have to make some stiffening adjustments and fining tuning the ride settings to my liking but other than that the suspensions has been great! I think you will enjoy it!

did the RSR deletes fix your chassis warning issues?

@RebuildEverything

Жыл бұрын

Yep took all the codes away!

Do you have a link to the mount used upfront for the remote ?

@RebuildEverything

2 жыл бұрын

Here's the link to the one I purchased! www.amazon.com/gp/aw/d/B07L3Q7Y4F?psc=1&ref=ppx_pop_mob_b_asin_title

@mkv_garage

2 жыл бұрын

@@RebuildEverything thank you so much bro. I’m order it now my airlift kit just came in.

Hey bro your video helped me out tremendously but I’m totally stuck on installing the ride heigh sensors. I started on the rear and installed one exactly where you did the 2nd time around. I measured the travel for the 3rd hole around 4.5 inches but if I jack up the brakes to fully Aired out position it goes way past it’s limits. Any additional info on things like the linkage length from nut to nut would help. Thanks!

@RebuildEverything

2 жыл бұрын

Glad the video helped! Tomorrow I will measure the nut to nut dimension for you, the calibration mode is really good about telling you what you need to adjust on the height sensors. They were a real pain tho to get just right

@VinhTran-ec8bg

2 жыл бұрын

@@RebuildEverything Thanks! I haven't gotten to running the lines yet I spent the most of 2 days trying to find missing sockets or going to buy tools and dealing with stubborn nuts and bolts. Also did you use the existing nut in the spot you mounted the height sensor in the front? Are there any issues affixing the linkage to the front upper control arm when steering?

@RebuildEverything

2 жыл бұрын

I did use an existing nut for the front, after a few hundred miles I’ve had zero issue with mounting the linkage to the control arm. As for the nut to nut dimensions: Front is 3 7/8” Rear is 6 1/4” For the front height sensor my linkage is mounted on the 2nd hole and for the rear it’s mounted on the 3rd hole Hope this helps, If you have any other questions let me know!

Where did you connect your ignition from ?

@RebuildEverything

Жыл бұрын

I tapped into a fuse in the trunk, if you open the access panel on the right side you will see a 7.5 amp fuse on the furthest bank to the left. Thats the one i used, dont remember exactly what is was but it works perfect. Hope this helps

What is the psi you running in the front and rear

@RebuildEverything

2 жыл бұрын

I’ve been running between 45-50psi in the front and between 95-100psi in the rear

Where did you buy that system?

@RebuildEverything

2 жыл бұрын

Purchased it right from Air Lift Performances' website. Here's the link to the suspension I bought www.airliftperformance.com/vehicle/toyota-supra/

Mine did not calibrate says limits reached

@RebuildEverything

2 жыл бұрын

That means you need to adjust your connecting rod length. The calibration should tell you if you reached your limit going up or down then you can shorten or lengthen the rod. After that you should be good to go!

@JohnJacobJose

2 жыл бұрын

I got it to work thank u again