Cool video my dude. Beautiful Jeep and even more beautiful scenery. Very cool you get to share that with your son.

@BullGearOffRoad

3 жыл бұрын

thanks Shawn!

What a great dad you are. Those memories with your son with last forever.

@BullGearOffRoad

2 жыл бұрын

Thank you.. he is however my grandkid but it's all the same. He really loves it as well. He's always asking to go camping or off-roading.

Excellent video and review

@BullGearOffRoad

3 жыл бұрын

Thanks Carl!

Beautiful scenery

@BullGearOffRoad

2 жыл бұрын

It really is!

cool footage!

@BullGearOffRoad

3 жыл бұрын

Thanks!

Great video

@BullGearOffRoad

3 жыл бұрын

thanks!

Your truck looks amazing! Thanks for the video. Most videos focus on the install and nothing about living with it afterwards. How does the truck ride compared to the stock suspect? Mine rides smooth in stock form and I don't want to lose that aspect when I lift it. And how much rake did the Mopar lift leave on the truck?

@BullGearOffRoad

2 жыл бұрын

Thanks Derek, I do like the ride and I must say the mopar lift feels factory to me. I still had some rake to it but a 3/4" daystar lift fixed the rake. Since then, I've added a 3/4" rear Daystar lift too because of the weight I now have back there. So far, I've been pleased with it.

Very cool!!

@BullGearOffRoad

3 жыл бұрын

Thanks Mark!

Liked and subbed. Just a 2023 Gladiator Rubicon and trying to figure out what to add to it. I bought it mainly to take my grandkids for rides in the summer with the roof off. Any advice would be greatly appreciated

@BullGearOffRoad

3 ай бұрын

very cool.. where you from? I've added quite a bit to mine since.. I'm going to do a video soon with all the upgrades.

Do you ever get any rubbing on your fenders from your tires when it articulates? Or I guess I should say inner fenders?

@BullGearOffRoad

2 жыл бұрын

I did in the rear a bit but I added a 3/4 inch spacer from daystar and I don't get it anymore.

Nice video man. Which 3/4" front level did you go with? Did you just keep the mopar 2" lift kit bump stops in or replace those with the leveling kit bump stops? Are those the Black Rhino Armory rims? Are they 17x8? Thanks man and I appreciate all the info you put out! Getting my mopar 2" lift installed this week.

@BullGearOffRoad

2 жыл бұрын

Hi Micah, thanks for reaching out. I went with a Daystar leveling kit. You keep the Mopar bump stops and the kit is actually two spacers that go above the coil springs so It's you maintain the factory ride. It's been about 10 months now and I must say I'm pretty pleased still with the ride. I just need to add the rear kit now because of the added weight I have currently. that will also be a Daystar kit.

ok , you've had it installed for a few months now, how is it ? Did it settle at all? Did the shocks fade? Do you wish you got a kit with an adjustable control arm? I have a Gladiator Rubicon with the stock red fox shocks, and it sit's stinkbug and sways too much like a Cadilacc. Does the Mopar lift sit level? Did it align with enough castor? I'm about to buy a lift, so thanks for the help.

@BullGearOffRoad

3 жыл бұрын

So it's definitely settled but I don't think I've lost anything in terms of lift. The rear springs do feel softer and I feel I may need more there. I was able to get it aligned to the recommended settings as far caster/toe. I did end up getting a SteerSmarts adjustable track bar and that really helped in terms of steering wheel dampening.

@CoeShow619

3 жыл бұрын

@@BullGearOffRoad Thanks, I thought of one more thing. I am a very experienced mechanic and understand the whole installation process and have the ability to do it myself. Did you do yours yourself, or did you have a dealership do it? My wife says that’s the only way to maintain warranty. We have a new 2021.

@BullGearOffRoad

3 жыл бұрын

@@CoeShow619 I did do it myself.. the dealerships here are pretty good when it comes to honoring warranty work. Even if you did the work yourself.

Very nicely done. Maybe I missed it, but where are you located? Unbelievable scenery

@BullGearOffRoad

3 жыл бұрын

I'm in Northern Nevada, Reno area... this was right outside of Reno.

What size tires are you running? I am getting my molar 2 inch installed next week and plan to just run 35 so I won’t have to regard. Your Jeep looks great. It won’t be long that your co pilot will be at the wheel. Thanks for the video.

@BullGearOffRoad

Жыл бұрын

I'm running 37's in that video. I recently went up to 38's and still running the mopar... got some rubbing now but may go higher soon.

Nice video... I’m a new to the Jeep world I had the same 2” lift installed on my Gladiator. Did you replace the track bar? I wasn’t sure if it was necessary. I don’t plan on doing any kind of rock crawling.

@BullGearOffRoad

3 жыл бұрын

Thanks! It is not necessary to replace the trackbar with this kit as it only moves the axle about 1/2 inch off center however I did replace the trackbar with an adjustable trackbar because I also added a 3/4 inch leveling kit... plus it helps tighten up the steering a bit.

@eddiegarcia1026

3 жыл бұрын

@@BullGearOffRoad Did you use factory spring isolator with 3/4 inch leveling kit?

@BullGearOffRoad

3 жыл бұрын

@@eddiegarcia1026 Yes, you still use the isolator with the 3/4" leveling kit. I believe with the 1.5" kit you don't.

@joeymoreno3949

5 ай бұрын

If I purchase the mopar 2” lift kit, is there anything else you recommend ?

Encounter any rubbing at full flex at all? Looked very close in a few video shots. Hope you tested at full articulation. I guess with the offset and backspacing this helped out a lot if there was no rubbing. I went with a 3 1/2 clayton lift kit. with a -12 mm offset rim and 4.5 inch backspacing.

@BullGearOffRoad

3 жыл бұрын

Only in the rear, I didn't get any rubbing up front. how are you liking that Clayton lift? that's a good size lift.

@karthikkailash535

2 жыл бұрын

@@BullGearOffRoad how did you deal with the rear rubbing?

What kind of offset do you have on the wheels? Jeep looks good for sure.

@BullGearOffRoad

3 жыл бұрын

-18mm Offset; 4.50-Inch Backspacing. . Thank you!

Is that the Mopar Grill guard? Tried going through your vids but didn't see at what point it was installed. Great Build and vids, new follower here.

@BullGearOffRoad

2 жыл бұрын

Yes, it is. I got it with the bumper.. should be in one of my videos where I install the Winch.

Do you think the Mopar lift can handle whoops and going a bit quicker through the dunes?

@BullGearOffRoad

2 жыл бұрын

Yes, I do. I have taken it to the dunes but the springs are mainly the issue.. the rears seem to soft, so I would probably get stiffer ones in the rear.

Where do u live? It is beautiful there..rig looks awsome..love the way you paint matched the wheels!

@BullGearOffRoad

3 жыл бұрын

Sparks, Nevada.. next to Reno. Thanks! That is actually a color that Black Rhino Wheels offer from the factory.

Is yours exodiesel? I just installed on my ecodiesel and it only gave me 2" on my gladiator sport.

@BullGearOffRoad

Жыл бұрын

I think it's because the ecoDiesel is much heavier and probably uses different springs.

Subscribed and liked! What a beautiful place ❤ Sir, how big are the tires and what brand?

@BullGearOffRoad

Жыл бұрын

Those are 37" Mickey Thompson Baja Boss M/T's

@dawood2u

Жыл бұрын

@@BullGearOffRoad that is too big for my axle and gear

Please, please, please, tell me what music you used for the video!!!!!!!

@BullGearOffRoad

2 жыл бұрын

Hi Carlos, I get my music from Epidemic Sound. Go check them out.

Excellent Music, it reminds me of Blade Runner

@BullGearOffRoad

2 жыл бұрын

Classic Movie.. I'm glad you liked it.

Great vid- informative and beautiful. But where do you hang a hammock??? Lol

@BullGearOffRoad

2 жыл бұрын

I'm working on that! ha

So wat exact lift do u need for the Jeep Gladiator to be leveled? A "1.5, "2.0, or "2.5?

@BullGearOffRoad

3 жыл бұрын

1.5" lift would level it out. I have a 3/4" which still leaves a little rake for me in case I plan to put some stuff in the bed later... which I do.

@TheLakeShow323

3 жыл бұрын

@@BullGearOffRoad u have a 3/4? I apologize i dont follow? I own a jeep gladiator overland and i was told by 4 wheel parts a "2.5 lift is leveled, no consistent responses. Thank u for responding sir.

@BullGearOffRoad

3 жыл бұрын

@@TheLakeShow323 3/4" is just the leveling kit. The lift on the jeep is 2" plus a 3/4" inch leveling kit up front so technically the front of my Jeep is 2 3/4" with leveling kit and 2" in the rear. If you were to do no lift but just wanted to level the front of the Jeep, you would need a 1.5" leveling kit up front. Does that make sense?

@TheLakeShow323

3 жыл бұрын

@@BullGearOffRoad yes sir it does, i appreciate ur patience 😅

@BullGearOffRoad

3 жыл бұрын

@@TheLakeShow323 glad to help .

Any issues with your front driveshaft? Not hitting anything?

@BullGearOffRoad

2 жыл бұрын

No, not at all.. I checked a few times.

which drone do you as well?

@BullGearOffRoad

3 жыл бұрын

It's a Mavic 2 Zoom.. so far, I like it and it does well.. just need to get the setting dialed down a bit more.

are those 37s? they look great

@BullGearOffRoad

3 жыл бұрын

Thanks! Yes, they are 37 inch Mickey Thompson MTZ P3's.

Are these 35s or 37‘s? I can’t seem to tell

@BullGearOffRoad

2 жыл бұрын

Those are 37's. Mickey Thompson MTZ P3's

✌️✌️✌️