Use code RCTESTFLIGHT50 to get 50% off your first Factor box at bit.ly/3JgFdFQ

@MML66

10 ай бұрын

This made me think that if I put a magnifying glass on it, will it increase the energy or will it just burn? 15:00

@Cuadra2077

10 ай бұрын

friend, you do not have to wait for another type of propeller to be invented, you can be inspired or copy the propellers of submarines, there are many and with different characteristics, especially nuclear submarines, they have the most efficient propellers in history.

@doolittlegeorge

10 ай бұрын

Higher *"peak thrust"* should be great as the goal be to as quickly as possible *"step up"* (transmission re: new Mercury Outboards have an automatic transmission) to *"ON PLANE"* (ride atop the water and On the Level to vastly improve hull efficiency at speed.) Once *"on plane"* can then "step down" (Downshift) to control all three vectors on plane meaning pitch, yaw, and roll the Holy Trinity of Boating. This also can be measure beyond mere time over water versus time over land under water which should yield two different velocities no different from aircraft time at speed in air versus time at speed over "land/water" the latter often surprisingly high/beyond the ahem "speed of sound" ahem. In Boating the effect trying to be created is no different from that which a hydro foil does...only without the hydro foil/propeller only plus shaft.

@borisnazarenko6134

10 ай бұрын

DID YOU EVER LOOK AT SUBS SCREWS? THEY USED TO HAVE SEVEN SCYTHE BLADES AND FOUR RIDGES ON THE HUB TO CANCEL CAVITATION. THIS WAS DONE TO RID OF NOISE, BUT ONCE YOU CANCEL NOISE COUSING CAVITATION, YOU GET RID OF DRUG INDUCED BY IT. THEY DIDN'T DO NINE BECAUSE BLADES WERE BECOMING FRAGILE. BUT YOU CAN TRY TO PUT THEM IN TWO ROWS. THE HUB ALSO HAS TO HAVE RIDGES AS IT HELPS TO CANCEL CAVITATION. BUT ALL OF THIS ONLY WORKS FOR HYDRODINAMICS, NOT FOR AERODYNAMICS.

@bubbaseeds

10 ай бұрын

1 I like the boat 2😊3 The prop discussions not for us. 5 where we at 6 let's worry about energy consumption and storage in collection

Finally someone just 3d prints the traditional design to be able to compare it with a 3d printed new design.

@filgiupo4853

11 ай бұрын

Yup, very clever and it makes sense at least!

@youtubebandme4382

11 ай бұрын

🤦

@1islam1

11 ай бұрын

@@filgiupo4853 ⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran

@holycaketree

11 ай бұрын

@@1islam1 The fuck? You good?

@Skaadi89

11 ай бұрын

​@@1islam1ow does this apply to anything in the video?

The air bubble test at 21:22 is awesome. Great work, I enjoyed this video.

@rctestflight

11 ай бұрын

Thanks Dustin!!! Means a lot. Big fan of your videos!

@girthtrude5040

11 ай бұрын

you guys need a colab

@scferro

11 ай бұрын

Agree! That was a great visualization

@ashleigh.

11 ай бұрын

@@rctestflight He heard you utter the word "laminar" at 34:43 and was drawn like a shark to blood lol

@snooter28

11 ай бұрын

You two should collab!

I am astounded by your knowledge of technology. I’m 60 years old and I am known among my friends and family as someone who can build or fix anything. Metal fab, wood fab, automobiles etc. . I’m not computer illiterate but my knowledge is like two fingered chopsticks on a piano compared to the symphonies you compose. My mind is just not geared towards what you are so good at. I am envious but all I can say is “GOOD FOR YOU”. You apply yourself with a passion and have earned your knowledge. I think you are destined for great things.

Thank you for addressing the issue of print quality. Every video I've seen about 3d printed toroidal propellers uses some abomination made on a $150 3d printer. It's nice to see someone go with a good print quality and smooth surface finish. I also found it interesting how you discussed the thought process behind your CAD design, and how different design choices could impact the propeller's performance.

@moist_moss

9 ай бұрын

melon

@ImDelphox

9 ай бұрын

melon

19:10 Standing barefoot in a boat full of batteries and Chinese power supplies while it's raining definitely demonstrates your dedication to science.

@nathanchalecki4842

11 ай бұрын

Hahahahahha

@X4Alpha4X

11 ай бұрын

i mean it sounds bad but even if he stood on bare metal at 24-48VDC he wouldn't feel anything really. one its DC and two, the voltage is too low to pass any real current given the skins resistance.

@ExtremeSquared

11 ай бұрын

@@X4Alpha4X 24-48vdc easily passes current through wet skin. If it's the path of least resistance, which it probably isn't in this case. Also, there are a multiple 120vac inverters in play down there.

@X4Alpha4X

11 ай бұрын

@@ExtremeSquared i mean yea sure some current will pass, but from foot to foot with wet skin, youre looking at like *maybe* as low as 10,000 ohm (a multimeter says my dry feet are 1,500,000 ohms so im being generous), at 48v thats 0.0048 Amps, thats juuust barely under what you'd need in order to even feel it since google says 0.005 A is the lower threshold for DC. and again, thats the absolute worst case scenario of you standing across the full potential. the most likely failure would be the terminals shorting though the water and dropping in voltage to the point everything would just turn off.

@ExtremeSquared

11 ай бұрын

@@X4Alpha4X Soak feet in saline for an hour, then retest. You might be surprised how low skin resistance goes. Like you say, the big safety mechanism here is configuration. Almost all configurations of body / potential have a salt water bridge of lower resistance in the circuit. Maybe some really awkward fall could put 24v from a waterlogged hand to waterlogged feet combined with a connector/wire failure, but that's freak accident territory. For what it's worth, I was really just trying to get the attention of alarmists with my post.

can you build a submarine, that can be driven with a controller?

@lightpolebluelamaa4207

11 ай бұрын

Then you should look at the titanic

@okami220

11 ай бұрын

LMFAOOOO

@Eidolon1andOnly

11 ай бұрын

So edgy

@bobsnabby2298

11 ай бұрын

They tested it already, wasn't a good idea.....

@superfluous9726

11 ай бұрын

Make sure it's only safe to like a third the of the depth you're planning on taking other people too!!!

I'M SUDDENLY SO INTERESTED IN E-BOATS AND THE EFFICIENCY OF THEIR PROPULSION SYSTEMS. Phenomenal video. My brain enjoyed all 36 minutes of it.

Big respect! Its ppl like you that makes the human race and planet earth go forward. Seriously, thank you!!

As an engineer, I really appreciate the way you present your videos. You build cool things, explain your thought process and provide high quality shots while cracking subtle humor 😊

@flat-earther

11 ай бұрын

hi erikp, have you become a flat earther yet?

@petemack3076

10 ай бұрын

The benefit comes when attaining a plane. At low and high speeds, the efficiency gains are marginal. But getting on a plane at 2500rpm vs 3500rpm is a huge benefit.

@fuckednegativemind

10 ай бұрын

​@@flat-earther Why would someone become a flat earther?

@flat-earther

10 ай бұрын

@@fuckednegativemind because we were all lied to when we were taught that the earth is a ball flying in a vacuum

@winzracingNZ

10 ай бұрын

It's a formula you can find all over yootubez my man... But then, I appreciate, this is done very well. Not being able to afford one battery of this type or capacity... But having univershity degrees that suggest I should... Life Sadly isn't a predictable science.

I’d build a static test rig that sits in a swimming pool or pond and measures the force output. That way you can easily step through a series of speeds and get a graph of kN/Wh plotted against rpm. It would also make it more viable to keep printing a bunch of rough FDM props for rapidly testing new designs.

@flat-earther

11 ай бұрын

hi Scrogan, have you become a flat earther yet?

@Millie_1075

11 ай бұрын

​@@flat-earther I have a question if you're a flat earther explain to me when a boat is moving away why does it look like it's going over a curve and not a straight line?

@flat-earther

11 ай бұрын

@@Millie_1075 Why does the farthest street light in a row of street lights look lower than the ones closer to me?

@Millie_1075

11 ай бұрын

@@flat-earther this is from a website that has research, Follow ships on the horizon If you’ve been next to a port lately, or just strolled down a beach and stared off vacantly into the horizon, you might have noticed a very interesting phenomenon: Approaching ships do not just “appear” out of the horizon like they should have if the world was flat, but rather seem to emerge from beneath the sea. But, you say, ships do not submerge and rise up again as they approach our view (except in Pirates of the Caribbean, but we are hereby assuming that was a fictitious movie series). The reason ships appear as if they “emerge from the waves” is because the world is not flat: It’s round.

@bamischijf_2757

11 ай бұрын

​@@flat-earthershut up bot

Don't stop prop testing, that was honestly very informative!

One thing I have learned about props is, there is a sweet spot at speed verses revs UNLESS you can vary the prop geometry. Cheers Mike!

Mad props to you for doing all that testing.

@AlbertaGeek

11 ай бұрын

You're why we can't have nice things.

@TheChaos01

11 ай бұрын

Love the use of "props" in your comment😂😂

@tvuser9529

11 ай бұрын

Came here to say the same. Great minds etc.

@wildekek

11 ай бұрын

I see what you did there

@eekee6034

9 ай бұрын

@@tvuser9529 What saying is that? "Great minds think alike, fools never differ"? 😈

You are one of my “instantly watch” KZreadrs and I don’t do anything with boats or RC anything. You are just so good and explaining stuff and have a good sense of humor. I love you

@Sniperboy5551

11 ай бұрын

I don’t even read his titles, I just click. Every single video is awesome, regardless of what I’m in the mood for.

@__gavin__

11 ай бұрын

Yep same here! One of the few people I have notifications turned on for and just watch every video without even reading the title - always know it will be interesting. And I'm not into RC or boats either.

@coarse_snad

11 ай бұрын

I mean, this really is just an engineering channel with "rc vehicles" as a cover story :P

@naerbo19

11 ай бұрын

If it's a neon green profile pic in the feed, yes please.

@Studio23Media

10 ай бұрын

@@coarse_snadYep, you're exactly right. The RC is mostly just for his testing platforms. 😂

Just looking at your OnShape sketches... wow! That's SOME work, well above my level. Thanks for leaving them public, hopefully studying yours, might improve my skills! 👍

Really interesting! The higher vibration of the FDM may come from the fast that they are not as stiff as the nylon - so the blades actually flap around a bit. I have been casting some propellers for electric outboards (we are breaking lots on our shallow stretch of river). I started with a hard resin and it worked great, but there were significant vibrations and eventually the propellers self destructed at the join of the blade to the shaft. So then I put 10% milled carbon fibre in the resin and this made a HUGE difference - as good as the OEM ones and they were lasting way longer (never sure if it is self destruction now or user error). I then added a 6 hour soak at 50degrees Centrgrade, which stiffened them even more and they are now performing really well - I have to be careful not to take them out of the mould when they are green or I can deform the geometry, so a 12 hour cure, then a 6 hour bake and they are super stiff (but a bit more brittle!!) Love this kind of content!

"I promise were finished prop testing" why,? That's what I'm here for. These videos could be an hour and I'd still watch till the credits. Love your stuff!

OK I totally was not expecting that awesome demo with the bubble tube. That came out EPIC. You make filming this stuff look effortless.

Great vid! Really enjoyed it. Idea: With the two motors put a different prop on each one to see if the boat tends to go let or right to find the more efficient prop.

the flow visualization is darn cool! it's one thing to see these things in CFD simulations like SolidWorks, but to see the actual physics at work is totally another thing!

On your standard prop blades you need to cup the top edge of the blades. It helps a lot on Boat props less cavitation.

@thomgizziz

11 ай бұрын

You mean make it more like the other design... you don't say...

That ship 5:01 is actually called Sherpa, built at van Lent in The Netherlands. It's only a couple years old, purpose build as an exploration yacht. I've seen her many times when she was being finished at the yard. Cool to see she is at the other side of the ocean now.

@evancourtney7746

7 ай бұрын

Ship at 5:56 is USNS Vice Admiral K.R. Wheeler, there should be a smaller sister ship around named USNS Fast Tempo. Together they are TRANSCOM's Offshore Petroleum Distribution System.

I learned something I never knew about propeller efficiency Thank you for sharing your experience and life with us ❤

Awesome video. Love how honest you are. So many KZreadrs made a design, with crap materials or printer, and then called it a day. You admit there is more to it than just copying the look, and say it looks good. When there is much more nuance into it. It is like a sword like a Falcata or Kurki. What seperates a good one from a knock off is not just the profile or how it looks in 2d space. Yet whether it has a good distil taper as well. Cheap ones will knock out the shape, and it is basically flat metal piece with a small edge. Instead of the spine or length of blade having different widths to balance it. It makes a huge difference in any sword really.

i really appreciate your testing you did, not just 2 days but 3 days of testing (plus reading/researching/sanding/editing) is a lot of work! Loved the air visualization on the prop too, very clever

Awesome work! Let me say that designing things like this is EXTREMELY difficult. Many fluid flows don't act as you expect, especially in real world conditions. This makes real world testing incredibly important for optimization. Mad respect

@blahorgaslisk7763

10 ай бұрын

It's the same with just about everything you design. A customer designs antennas for mobile phone networks. They spend months on a theoretical design, simulate it using the most advanced software available, and then build a prototypes to test that what the simulations and models claim is what really happens when you use them. Most of the time it's close, but sometimes they get a surprise. These computations are pretty heavy. I remember that before the code was revised to use the GPU's the fastest computer we could build would take several hours to simulate the radiation patterns of the antenna. It's the same with fluid dynamics. We know a lot of how it may work, but once we've worked with the known theories and designed something that works well in fluid dynamic simulation we have to build and test a prototype to see just how close to the simulated results we get. The software has gotten so good that usually there's very little difference between theory and practice, but every now and then there's a surprise. And this is especially true when trying to invent a new profile or radically different design like these toroidal propellers. There hasn't been anywhere near as much data for these shapes to verify the computation models against the real world results.

@DeuxisWasTaken

10 ай бұрын

@@blahorgaslisk7763 it's especially true for something like a propeller that works in a very dynamic environment. Simulation software usually works like a wind tunnel, exposing the test subject to a stable environment, while a propeller will constantly encounter variations in the speed and direction of movement and even density of the material it's propelling through, and the uniformity of those values over it. The way it deals with those variations can both affect its performance and be independent of its performance in a stable environment. And we'd be simulating for months if we wanted to test a decent range of situations.

I love your idea for the air bubble test! and then your idea to use the shutter speed to see what's happening more easily!

Props for redoing the test

I think your problem is that you basically have two parallel blades which are connected abruptly. In other words, at 23:00 you can see that the center of the blade in the image (the line made from the middle of the distance between the inner and outer line) look like a square/rectangle with rounded corners. I think that by elongating the toroid, so that it looks more like half an egg or like a semi-circle or semi-oval, you would get more continuity for the flow, and the higher angle of attack would mean that instead of making a vortex, the water would continue along the blade, from the beginning to the outside to back into the center at the end, and end up either not making a vortex or making only a smaller vortex in the center of the axis of rotation. Also, I think you need to watch the angle of attack not only at from outside in, but also from top to bottom (slicing the blades in CAD/ONSHAPE). Your toroidal propeller starts at 45 degrees from the direction of flow (of air or water), then go to 60 degrees on the outside, then back to 45 degrees. You could try making it 30-45-30 degrees, the higher angle of attack reducing the stalling. Also, I think the propellers they currently sell are simply moving the vortex from the tip of the blades to between 1 third to half of the outside to the inside, which lead to the vortexes being smaller due to the smaller tangential speed at that radius/diameter (when compared to the radius/diameter of the whole wing, form the center). Also, please make a few more blades, one with normal blades angled 45 degrees from front to back (like the top blade at 26:53) to push the water inwards, one with the angle -45 degrees to push the water outwards, then another one with double blades at 45 degrees, then another one with double blades at -45 degrees, then another one which to start with 45 degrees blades then below them to have -45 degrees blades even if they're not connected making them look like a rhomb, then another pair which to have the -45 degrees blades then below them the 45 degrees blades looking like an X, all with the same radius/diameter as the normal ones you already printed, then another one which to be a normal propeller with winglets which to have an average of 45 degrees of angle side to side (60 degrees of angle from the tip of the blade which cuts the water, and 30 degrees of angle from the tip which merges the water together or creates cavitation, the average 45 degrees basically making the winglet, when looking from the outside of the blade to the axis of rotation, moving down and to the side of the blade). This will give you the best range of test data, in my opinion, which could help you design a much more efficient propeller. If you have any questions, feel free to contact me on discord @Sapioit for more details. I'm looking forward to the results of your tests!

@r0cketm00se3

11 ай бұрын

I was thinking this same thing, it seems like he just squared it off which is not part of any toroidal that I've seen. They usually come down to a very slim edge at the transition point of the tip.

@redgopnik2227

11 ай бұрын

lmao this is the first time ive seen a discord handle shared in public like this after the number discriminators were removed and i think i might not hate the change after all

@SapioiT

11 ай бұрын

@@r0cketm00se3 Thanks! And the sheer number of different blade designs, even if made from cheap print-at-home materials with proper smoothing (like he did in the video) would reduce the need to spend lots of money to have a company print them, so having that many different designs would help narrow down the science behind the fact.

@SapioiT

11 ай бұрын

@@redgopnik2227 I have nothing against the new way, I just think that the change will break a lot of things, including older messages on the internet. If people were still able to use the old way to send friend invites, in perpetuity, just no way for new people to get that exclusive invite code, then I think a lot less people will dislike the change. Unfortunately, small changes from big websites and apps will have a huge effect, because they are inevitably used by a lot of people, and in many cases by a lot of other apps, too. Like how the Reddit API caused Reddit to lose stock value, and some investors are already suing for fraud (because he or someone he knows most likely sold their shares before the announcement), using the "going public" as an excuse for the inevitable fall of the company.

@seldoon_nemar

11 ай бұрын

Have you seen a Sharrow prop? they are a commercially sold toridal prop that's been on the market for like 30 years Expensive as sin, but supposed to be "the bees knees"

10:30 I think it's important to note that for a foil of finite span, there will always be a tip vortex if it is generating lift at all. You can reduce it, but never get rid of it completely.

@aerobrick1251

11 ай бұрын

The vortices dont necessarily need to be at the tips. For a lift distribution where lift goes to zero and it's derivative also goes to zero the vortices can be moved inboard. This has been experimentally demonstrated on the nasa prandtl aircraft, and may also be the case for some birds.

@beatyoubeachyt8303

11 ай бұрын

honestly I think you can get rid of them if you make a design that cancels out them like noise canceling headphones you can possibly cancel out the tip vortex with another tip vortex like noise canceling headphones do with sound because sound is using air

@aerobrick1251

11 ай бұрын

@beatyoubeachyt8303 A wing with finite length has force up in some areas, and not in others. As such the air must circulate in order for the net system vorticity to be zero, which in the far field should be true. There will be vorticies, just maybe not at the tip

@garyhsk8

10 ай бұрын

Duct

"You're not really supposed to do that but it's fine" describes my life

@ABIGD0NK3Y

3 күн бұрын

like i say a at my friend's fab shop we make barely happen every day

I just discovered this video and am impressed. The engineering legwork you did behind the scenes is top-shelf quality. Combined with the tight narrative and the video editing choices, this content is excellent! Thank you for publishing this!

I want more prop testing seriously when you do testing like this. I think are some of your best videos.

@FayezButts

11 ай бұрын

seriously. Inject that science directly into my veins

You could add a load cell to the transom and measure the force applied by the propeller vs the power consumed. This would be a faster way of testing, and you could ramp up power and get a performance curve.

When I was in high school we had a prototyping 3D printer very similar to the SLS printer, except it was just some chalky powder with glue sprayed down onto it layer by layer rather than plastic being melted. I was still able to print out some pretty cool things with it, and eventually we even got an upgraded one that could do color printing, that was really fun.

Love the experimenting and data collation. Thankyou for the upload

Much respect for the amount of work you put into your videos, this was a big undertaking and it was an informative and fun watch too.

I love how thorough your investigations are compared to other youtubers, most of them do one iteration and then make conclusions. You seem to really try to understand all the aspects of the problem. Thank you for your content man 👨

I was not expecting to enjoy this video as much as I am. I like how casual and humble you are!

wow. i learned so much from this. you answered all the questions i had about this prop design. you are a legend

Interesting. I did a lot of prop testing with my solar electric boat, but one advantage I had was that my hull is a wide beam catamaran with each motor mounted behind each hull, so I use independent thrust of each motor to steer the boat, which means the simplest way to test and compare props is to put one on one motor and a different one on the other and see which one overtakes the other causing the boat to steer in one direction or the other at various speeds while monitoring power consumption and speed. So far, the Torqeedo props seem to be the most efficient highest performance props available. I think stiffness of material, chord profile, and tip sweep are all factors that play into this. Also, I think a cavitation plate helps and since I’ve added remote electric trim and raised my motors, I’ve found they perform better closer to the surface just under the cavitation plates allowing my hulls to semi-plane.

I love what you are doing and especially your humble approach. You say you are not a scientist, just a youtuber. Yet you are methodically testing a theory, providing blueprints through an open-source platform and recording the experiments and uploading them to an accessible media platform. Feels like science to me. The best kind of science.

these videos are absolutely amazing I've learned so much about such a fascinating topic cheers, mang

I appreciate that your sponsor segment was actually fun and amusing to watch. Not just an ad, but some fun content. Kudos.

This channel is one of the few that I hit the like button before the video even starts. Idk why propeller/impeller designs are so interesting, but they are.

Sharrow has been doing toroidal boat props waaaaay before MIT's publicity-laden drone prop. And when it comes to efficency, both Sharrow and MIT say that ducted propellers are more efficient. Toroidal is just lighter than ducted setups and does not have the debris issue that ducted props do.

@TheBaconWizard

11 ай бұрын

I too, watched the video.

@GoldenCroc

11 ай бұрын

They have indeed been at it for a long time, but have yet to resent any evidence of it having an advantage to speak of against any reasonable run of the mill 4 bladed prop.

I really appreciate your work here. Best of success in your scientific endeavors for real life applications.

Great shots of Lake Union, esp the little steam boat! There's a seaplane base just right of where you said "these are probably scrap" that I used to fly in and out of, super fun!

theres a reason i love your channel always giving the straight facts

The noise reduction is supposed to be in the context of marine life, not occupants on the boat itself. It would be another interesting factor to test under water for at different distances and positions from the prop if you do another round.

A truly treatise on propellers and their aerodynamic concepts. Congrats! Cheers from Brazil.

Great analysis! I'm looking forward to seeing further developments!

I’m very glad someone can spend so much time testing things out and we can all benefit from a 36 minute TLDR video

I would think that the one of the reasons the toroidal and bi-blade props are so much less efficient is because the pitch is too steep. That would make sense based on what you found with the air bubbles, that the blades are in a stall.

@nielsdebakker3283

11 ай бұрын

The blades are very narrow as well. Looks not very efficient to me, it is more like an air prop.

@jackrosen1740

11 ай бұрын

@@nielsdebakker3283 I agree. They have a lot less surface area too, which I think is a big factor

The vessel in your video the VADM KR WHEELER I helped put the supper structure on in 2007 in Larose Louisiana. I ran a tug boat that held and positioned the large barge crane that put the super structure on the hull. Awesome to see her again!!

Thanks! I have a 30ft sailing yacht that I have been running off 3 solar powered electric motors for 9 years. My boat needs no fuel, she's powered by the wind and sun. I have 4 8D commercial batteries set up for a 24v system. I works good for me. I still need to sail for long distance trips but getting around my general area on electric power is no problem. I have 300lbs of thrust which 95% as much as the recommended gas engine size. I really enjoyed your prop analysis. I always keep my eye out for better props. Keep up the good work!

Something that i think would be interesting to see is the performance through rpm ranges represented on a graph. The thing that tryly interests me about it is when you mentioned the forward sweep of the lower blade on the bi-blade prop. Typically forward swept wings on planes have some interesting effects in transonic flight vs typical and rearward swept wings. 14:46

These videos are so informative and entertaining, keep up these awesome projects! Made me get into flying RC planes and even learned how to build my own plane with your help. Thank you

You could account for wind velocity by driving around a circuit course-corrected by speed-through-water rather than landmarks, which ia speed-over-ground. So drive one direction for set time, and calculate your velocity by water not landmarks (ground), change angle and repeat.

Awesome Video! I love to watch your DIY tests where you try everything with the things you have available! I hope there is a followup video coming! 😁

I love your spirit of inquiry, prototyping, testing, evaluation. Despite the tools being 21st century the spirit of your work makes me think of ways I might also describe the natural philosophers of the early modern period.

Love your commitment to accurate testing. Respect.

Man, you did such a good job!!

Props to you for testing props and finding out the probs with different props. Probably props probs.

If a wing is deigned for high speed, it should have a small aspect ratio to reduce form drag. It feels like the same rule should apply to propeller. As how fast a boat propeller generally spin, maybe winglets will cause more form drag than the induced drag it decreased... Also, wings stalls at a certain angle of attack, so it doesn't really matter how fast it is spinned. If it is stalled and a certain AOA, it stall at all speed.

@SoloRenegade

11 ай бұрын

changing prop RPM changes the angle of attack.

@kyriakos_kyriakos9103

11 ай бұрын

last time i checked wings stall at a specific speed for a given angle of attack, right?

@SoloRenegade

11 ай бұрын

@@kyriakos_kyriakos9103 wings stall at a specific angle of attack, regardless of speed.

@kyriakos_kyriakos9103

11 ай бұрын

@@SoloRenegade so when an aircraft is not stalled at a specific aoa and speed, if it keeps the aoa constant and starts reducing speed it will never stall?

@shiroyukiwang1252

11 ай бұрын

@@SoloRenegade how does change rpm changes AOA? Is variable pitch prop a thing in boat?

To test the thrust efficiency. Couldn’t you put the boat in a pool and have it push against a horizontally mounted scale and see how much pressure it puts against the scale. You could also test how much throttle it takes to achieve a certain pressure on the scale. The lake experiment is cool, but there seems to be a lot of variables that can’t be mitigated. Love your videos. So much trial and errors and refinement. Great work.

@inferno7181

10 ай бұрын

yeah but where's he going to get a pool from, pool salesman?

@Mr.ZooKeeper

10 ай бұрын

That’s the hard part? Where to get a pool? If that stopped him, he should just shut the whole KZread channel down.

@user-bf9qj3im7j

10 ай бұрын

The bay is a large pool. You could just anchor and tie up anywhere along the shore. However, not moving changes all the dynamics of the system.

That was really interesting, the amount of work you do in the background to get these all set up and working must be crazy!

This channel is totally awesome, fantastically scientific and inspiring ❤

You should build an aquarium air pump into your boat so you can do bubble tests with the push of a button 😁

Damn, this is an amazing set of tests! Really amazing work, and incredibly thorough!

The comparison between your bubble testing footage and CFD results really shows the power of current CFD tech... Just amazing.

Your testing is excellent, and I love how you explain all your logic. I love yr channel

Your underwater bubble trails look great, nice work!

In regards to this ingenious design that MIT claims to have discovered I suggest you look up the "ship's screw" by Josef Ressel from 1826! If it wasn't for a mechanical problem of the motor during the first test today we could have this type of propellers in much more use!

Thank you so much for pointing out the most obvious issue with 3D printed propellers so many seemed to have missed.

I have learnt a lot from your testing. As you mentioned, the shipping companies need to take note on propellor configeration efficiency to save on feul and engine wear.

Awesome video man, love to follow your geeky adventures. It is what I would do if I had the time, but at least I get to watch your journey. Loving the process of your videos and how you explain things. Keep them coming.

I love how you absolutely went down the rabbit hole on testing for this. Would be REALLY cool to see you do load tests with some kind of water-based wind tunnel. Could help you narrow down on a better prop design

Talking about the vibration in the two blades prop. Looks up vibration in even vs odd number of props. For example, most windmills are 3 bladed for a reason. Also, notice that the original toroidal props are elongated, not round, but still closed. That would prevent water slipping off the end, but would generate less lateral vortex.

One of the major differences i noticed in Sharrow Marine props vs 3d model you are using is the blade angle, not necessarily pitch but the way stern facing part of the blade is angled. So the loop is angled more aggressively toward the center of the prop. I would try prop design to perfect it further from there.

@karlkarlson3502

4 ай бұрын

You're expecting too much from this idiot youtuber lol

You know, you can just set up a large tub of water at your house, then run each design and get the same efficient data to sort out the best design 😃 And you can also quickly FDM print all different designs you think will be good to test, as long as you keep them all "rough" you can still sort out the best design from the efficiency data. Then send the best design to get laser printed, sand it, polished it and finally test it on your boat.

@sophie_a

11 ай бұрын

how do you test the conversion efficiency in a tub? we would know only how much resistance each propeller has, not if that power is getting wasted or converted to thrust efficiently

@sijmen2670

11 ай бұрын

It's definitely not the same

@FAB1150

11 ай бұрын

Maybe in a pool, something small as a bathtub or tub would have all sorts of turbulence coming back from the propeller itself

@sijmen2670

11 ай бұрын

@@FAB1150 I do lots of testing of outboard on test tanks, even on the low HP motors like 4hp, after a little bit of gas you hear de motor have less resistance and then more. These props move a lot of water! Even in a pool, you will create very large currents, it has lots to do with the depth of the water.

@julianpowers594

11 ай бұрын

That would be a static thrust test so by defintion the efficiency is always 0

Another interesting episode, your improvised bubble flow visualization is ingenious and very effective.

@ferocious_r

10 ай бұрын

wondering though if the bubbles won't contribute to flow detaching from the "airfoil" ("waterfoil"?)

So many incredible things to see in that harbor!

At 32:06 - your theory on vibration is probably spot on. Have a look at why windmills all have an odd number of blades. Great video!

I think the Real use case for toroidal propellers is in siring peanutbutter. Think about it, the vibrations caused by a normal stiring device or spoon would turn the butter into unrefined oil. Thus a toroidal propeller would keep it at optimal eating consistency at all times. Seems revolutionary to me...

@samtheengineer

11 ай бұрын

underrated comment

@baddestmofoalive

11 ай бұрын

Hahahaha nice throwback

Would be cool to see a test of those asymmetric low noise drone props used by Zipline. (They look a bit like your "biplane" prop but with only one pair of blades and an opposing counterweight.)

@daryl75052

11 ай бұрын

I came here to ask the same thing!

OH man, cant wait for anotheer boat video!❤

Thanks for the video, i find it very interesting! Wondering about these same things keeps me awake at night!

I never realized how interested I would be in propeller testing like this. I could easily watch hours of this content. I’d love to see more prop testing, but only if you enjoy it and it’s doable for you!

Little Info from an aerospace engineer: turbulent flow makes a foil stall less, not more. So the rougher texture should have less stalling. On aircraft wings you often have little structures to create turbulent flow, so the flow does not stall (especially where control surfaces are)

@ErikssonTord_2

11 ай бұрын

Turbulent flow makes the flow attach better at high angle of attack, but the drag of a foil with a blunt trailing edge is much draggier than one with a sharp edge, and something is wrong if the propeller stalls at normal speed forward.

i need more of this .... keep going 😁... you don't even wanna know how many episodes of major hardware's fan showdown i watched... yeah all of them... gotta get printing❤💜👍

At 14:38 in, I lived in a houseboat on that dock in 1980-81. The plant covered house is exactly as it was then. That's just off Lynn Street in Seattle on Lake Union, across the street from Mike's Grocery. We had a Laser sailboat and the lake was our back yard!

@SwampyColorado420

3 күн бұрын

Thanks, I was wondering where this is, it is so cool!!

I love the testing and especially the evil twin brother action. I was thinking a good test that eliminates a few variables would be to put one pf each type prop on and see if the boat turns with equal power on each motor. in calm wind of course.

the sharrow propeller was WAY different than yours. This was a good vid. Would be interested in a second attempt. May be interview an expert on props for fun.

@Powermongur

11 ай бұрын

Yeah the shape doesn't match and those are the only efficient ones i seen in production that people say that work.

I recently watched a video on microwave cooking by America's Test Kitchen where they basically said it's better to microwave at lower power settings for a longer time than it is cooking at full power. At the lower power setting the food is cooked more evenly. As someone who has used pre cooked dinners in the past (not Factor, they are new to me) I found out I got better taste and texture by putting them in a pan/skillet/pot than with keeping them in the plastic containers and microwaving them.

Thank you for testing for us.

I would love to see you set up some sort of water tunnel thing (like a wind tunnel but water) and isolate a lot of variables for testing the different propellers. Sure maybe you won't be able to spend a day or 3 out on the water but it would be scientific and thats cool

This was super interesting, I kinda hope you'll follow up with improved design(s) based on gained information here. I'd watch another video on the subject for sure.

If you model the outside edge ( the connected area between the blades ) of the toroidal propellor like as an extended two more blades you will reach your desired results, having a trivector propeller. The connection as it sets creates drag countering the propulsion of the second blade on rotation.