Excellent,easy to understand .Well explained.Thank you Sir.

Taught me something today, thanks!

So what exactly is going on here for it to show that drop? The way I'm imagining it (as a noob) is that when the pump pulls current down the main wires, if there's any resistance because of a bad connection or frayed wire, the voltage will try to pass through the multi meter circuit?

Hi, a quick question. At the pump connector, 12+, 12v ground. No problem. Reconnect at pump, pull relay out. Relay measures 12v +, when I go from batt 12v+ in series to pump side ground I get 5.98v through the NEW pump. Pump measures 0 ohms R now that it is cold. Bad brush? New pump measures 0 ohms, and no volt drop from batt+ in series. I changed pump, vehicle runs. Retest pump, 0 ohms res, no voltage drop. Was the 6v drop due to R from a hot / defective pump or did I miss something? Original pump was changed due to rotten tank as routine due to high mileage. I feel like I missed something!!!

Thank you so much. I replace the fuel pump and still have no power when I turn on the engine. I will do this test!!!!

When i do positive voltage drop, the meter is showing 12+ volts without even cranking the engine. Does this make sense? Shouldn't it be showing zero volts?

How do you do this test on a duty cycle pump??

I have 12.5 volts in my battery, and when i measure voltage back on the fuelpump positive terminal i only receive 12.3 volts, at this Point the ignotion is at it`s off position, is this normal, or should there me the same voltage back in fuelpump as in the battery?

@aamirghanchi9487

Жыл бұрын

I hope u were able to figure it out. I have the same issue.

Backprobe with t pins and alligator clips attached to the meter leads.

How warm should fuel pump relay get while vehicle running?

@NEMOJA

9 жыл бұрын

They get hot its normal

@3735geez

4 жыл бұрын

One of my pins burned. Put new one and almost burned. Replacing pump. Heard it could be problem

Uh...I'm getting negative 8 Volts at the pump connector

Too bad to get to the connector on many cars you pretty much have to drop the tank.

Hello i was wondering, when you do the voltage drop at the power wire at the fuel pump, do you need to disconnect the connector or leave it connected and just probe into the circuit? How about the negative side?

@robertofkennedy

7 жыл бұрын

Hector Arreola don't unplug load have to have a load "fuel pump" which creates current flow. Otherwise the test will not work

@hardboiledfrog

2 жыл бұрын

@@robertofkennedy it would have been nice to see how he had it hooked up at the fuel pump. just showing the lead to the jumper really wasn't helpful. Also, my pump is not running, but i believe it is not the pump itself that is bad. Since the pump is not running, i can't do this test, right?

good

My 2001chevy express stops while driving what can cause that the engine light does not come on

@jasonbarber5574

7 жыл бұрын

what caused that

@atomicdmt8763

3 жыл бұрын

figure it out? mine was doing the same.......... years ago. i believe i just cleaned my battery contacts........

Appeared to be a quality video until he failed to address meter connections at the fuel pump in detail. moving on down check....

U didn't show the wire from pump u talking about like wtf man

@bertrx-7406

7 жыл бұрын

i know right...idiot how would you clamp a huge booster cable to the positive of an in-tank fuel pump....even outside at the harness,,, HOW

@ollydbg9653

6 жыл бұрын

lol same here like are you kidding me

@Js-rq9uj

5 жыл бұрын

@@bertrx-7406 T-Pin

@robertwatson1510

Жыл бұрын

Attach the jumper wires to the battery terminals and use the T-pins on your VOM to probe the fuel pump terminals.

VOLT O MEATER

lol make and "modle"