I was looking at rear camber arms for my 3 a few months ago. I ended up getting the MPP arms after comparing all of those arms cause of the quality, look and ease of adjustment. I’m glad I did, I’ve been very happy with them. I wish this video had come out a few months ago, it would’ve helped make my decision quicker and easier.

thanks for another informative video, great to see all the arms back to back.

Thanks Rishie. Glad you sold me the MPP :).

I was going to do Megan’s, Tim made that decision very short lived and went Mountain Pass🤘

Fantastic video, thanks for the insight. Mountain Pass seems to be the move

@zevcentric

9 ай бұрын

MPP and N2itive are the easiest to accurately adjust.

Thanks!

Thanks for the video!!!

@zevcentric

9 ай бұрын

Our pleasure!

Thanks for your help!

Thanks for sharing this!

What are your thoughts on Redwood Motors Camber arms? Aside from availability and support.

@IDontGetGassed

9 ай бұрын

@zevcentric Rishie how come you didn't include the Redwood arms in the test? I know you spoke well of them during our convo last week.

@hyp36rmax

9 ай бұрын

@@IDontGetGassed my guess is lack of inventory and support? Redwood also operates as Sakebomb tuning RX7, S2K’s etc. their Redwood brand is a side gig with what seems like minimal focus.

@zevcentric

9 ай бұрын

The redwood arm is not a sealed spherical end like these other ones. It has its merit but I would say Redwood and SPL would be a better comparison tbh. @@IDontGetGassed

@zevcentric

9 ай бұрын

sorry I didn't see this. I think Redwood and SPL are a better comparison since they both share similar bearings. One of them uses jam nuts while the other uses pinch bolts and clamps.

Any thoughts on redwood performance? Debating them, unplugged performance, or mountain pass.

@zevcentric

21 күн бұрын

I have a set slightly used we can offer you as well as a new set. They use jam nuts and spherical bearings that aren’t sealed. MPP is still the easiest to adjust and have a quiet bearing for the long haul.

@07BSPtC

21 күн бұрын

@@zevcentric thanks I’ll probably go with mpp

@zevcentric

21 күн бұрын

@@07BSPtC send me an email zevcentric@gmail.com and we can ship them asap.

If my car is dead on the money straight, should i still get these?

@zevcentric

7 күн бұрын

@@dalea4350 if you have uneven inside tire wear on your rear tires then yes. If not then no.

Have you installed both MEGAN AND MOUNTAIN PASS on your Tesla and how would you compare driving quality between the two?

@zevcentric

3 ай бұрын

We installed Megans on over 20 vehicles and MPP's on probably over 1000 model 3's/y's. I can only tell you the Megans were absolutely horrible due to them failing that it's not even a comparison. In this case you get what you pay for. I never had a problem with MPP but 100% of the Megan arms failed on customer vehicles that we pulled them off the website entirely. Did you watch the video? The quality of the MPP sealed spherical bearing and the other materials used is on a whole different level. You can't compare a $150.00 steel part to a billet piece of art like the MPP arm that's made in Canada.

@TeslaSoCal

3 ай бұрын

@@zevcentric does the MPP CAMBER ARM work well even with the TESLA STOCK TOE, TRACTION, AND TRAILING ARMS?

This video is going to save a lot of peoples money, time and hassle

@zevcentric

9 ай бұрын

Sure hope so.

So the MP is the only arms you can do the alignment without taking the weels off?

@zevcentric

2 ай бұрын

Not correct. Where are you located?

@reviewsandstuff4447

2 ай бұрын

@@zevcentric I'm in TN. What arms do you recommend for longevity, comfort and easy adjustment? I'm ok with the more expensive ones, I rather buy once. I don't want to take the wheels off if I don't have to. Some alignment shops will give push back on that.

@zevcentric

2 ай бұрын

@@reviewsandstuff4447 please email us and we'll link you to recommendations on our website. LMK what all you are looking to purchase so I can package things together. I know you've asked for advice on several items. It's best we see the whole picture to build a cohesive plan.

@zevcentric

2 ай бұрын

zevcentric@gmail.com

@reviewsandstuff4447

2 ай бұрын

@@zevcentric thank you!

Megan Racing needs to focus on exhaust and other stuffs. LOL

Just returned my Megan order and will never order their junk again.

@zevcentric

Ай бұрын

agreed

Which arm has the lowest unsprung mass fraction?

@zevcentric

9 ай бұрын

MPP arm is the lightest but it's not by a huge margin.

do you need these if you drop lower that 1 inch

@zevcentric

9 ай бұрын

Yes

what about Redwood Motorsports cambers?

@zevcentric

9 ай бұрын

Still uses a jam nut but they use high quality bearings. Biggest difference is that the bearings are not sealed and need to make sure if the adjustment rod is nickel plated that it doesn't develop surface rust if you're in salty or snowy climates. The arms are beautiful though. Those are the only things to take into consideration.

Any coupon/discount codes for MPP?

@zevcentric

7 ай бұрын

I am sorry not for camber arms alone. Please email us zevcentric@gmail.com with your build plans. We will see how we can assist.

Yikes. Going from a bad execution to another for Megan. Just more reason to trust MPP build quality.

On the whiteline rear camber arm, what is the black rod for?

@zevcentric

9 ай бұрын

For headlight leveling sensor. Doesnt apply for usa market

@TweakedGSX

9 ай бұрын

@@zevcentric In this video, this appears to only be the upper rear camber arm, so do you adjust the front upper arm as well? In theory, you cannot adjust the rear camber properly without adjusting the rear upper front arm?

@zevcentric

9 ай бұрын

@@TweakedGSX that is correct. This is rear camber arm which is centrally located on the knuckle. Replacing the other rear arms isn’t needed for that reason. Plenty of factory toe adjustment. I think you are referring to the toe arm. The front upper control arm doesn’t have much camber gain when lowering a model 3 or Y so isn’t “required” to reduce uneven tire wear.

In a northern climate, what would you recommend for the treads on the MPP arms to keep the corrosion down?

@zevcentric

9 ай бұрын

The arm is aluminum and the tie rod is stainless. They already put anti seize on the treads but you will want to make sure you put more each season to prevent them from getting stuck due to mineral deposits that can cause surface rust.

I'm a noob. Why do our cars need these?

@zevcentric

9 ай бұрын

When you lower your car the top of the rear wheels tips in = negative camber causing premature inside tire wear. These arms allow you to fix that.

@dyhppyx

9 ай бұрын

@@zevcentric thank you