Finally a vid on the exhaust valve! Mine is stuck as f on my GSR750 :p I know what i´m going to do in the upcooming weekend :) Thank you so much for the vid

@GicaPhp

2 жыл бұрын

Glad I could help!

It helps a lot, my bike have the same situation and get fixed already. thank you!

@GicaPhp

2 жыл бұрын

Glad it helped!

Thanks mate very helpful

@GicaPhp

3 жыл бұрын

Glad it helped

Very nice! Thanks! 👏🏽👏🏽👏🏽👏🏽👏🏽👏🏽

@GicaPhp

3 жыл бұрын

Thank you too!

Thank you helped me a lot 👍

@GicaPhp

10 ай бұрын

Glad it helped

Awesome video, thank you George! I will do the same to my GSXR600 and hopefully would get rid of my FI C46 code too! Kudos!

@GicaPhp

2 жыл бұрын

Good luck!

@chriseverette7379

Жыл бұрын

I’m thinking about buying a 2011 750 gsxr and only has 3,500 miles but the seller has told me it’s showing the FI Light and it has to do with the butterfly exhaust valve and he’s asking 7000 for the bike but I don’t know enough about them can someone please give me some advice all he said that it was a little difficult to start up when it’s cold

@JuanjeteMS

9 ай бұрын

​@@chriseverette7379I know it's a little too late but... Yes, if the exhaust valve got stuck half closed It would be difficult to start. If you follow this video maybe you can fix this issue because it's a simple mecanism.

Good video, please more...

@GicaPhp

2 жыл бұрын

Thanks, will do!

Hi thank you for video really helped me just stuck on getting the cables back as it has pulled them in and i cant get them back thanks

@GicaPhp

3 жыл бұрын

No problem 👍 You will need to follow the cable to the motor and take off the rubber cover and you will be able to turn it by hand

Excellent video, George! I followed your instructions and got a C15 reading (engine coolant temperature sensor) according to the list you posted. Would this issue make the bike difficult to start? I got it started once but nearly exhausted the battery supply. TIA

@GicaPhp

2 жыл бұрын

Yes, a faulty ECT will create bad starting, the mixture could be too lean or too reach based on how the sensor has failed.

Great video! One question, when testing the motor the pull cable on the right pulled to the top position and is now stuck. Any idea how I get it back down?

@GicaPhp

Жыл бұрын

Power it up from an external battery

اخي ممكن تعطيني تعليل سبب ظهورها اول مرة fl

Great tutorial!! Do you have a service manual for the gsr750?

@GicaPhp

3 ай бұрын

Sorry, no

Good video, i have this problem every year as don't use the bike enough. So only gets used say once a month during the fair weather months. I find that i get the error on every 1st startup but leave the bike to warm up to about 60-80c, turn the bike off laving it off for 7 seconds and turn back on and no error as the valve can now move due to the heat freeing up the stuck valve. I have taken it apart just like this video and re-greased, which fixed the problem but only lasted for 6 months and get the same problem again. :(

@GicaPhp

3 жыл бұрын

Yes, I know the feeling. Unfortunately the grease will be burned by the exhaust gases.

@chriseverette7379

Жыл бұрын

Is this something serious???

@mav1937

Жыл бұрын

@@chriseverette7379 no not at all just a pain in the arse.

So was there anything blocking the valve? Did it just need WD40 and a big of a wiggle ?

@GicaPhp

3 жыл бұрын

no, no foreign objectes blocking the valve, just bearings siezed, I used a lot of wd4 and wiggle, I even put it in the drill and spin it until all was super smooth.

Frère, pouvez-vous me donner une explication de la raison pour laquelle il est apparu pour la première fois f1 ?

Hello, what is the color of the strings that you used for the plug

@GicaPhp

3 жыл бұрын

What strings?

If this gets stuck could this cause the bike to jolt or judder when riding it? (Similar to when fuel pump is about to fail) Am I right in thinking if it's stuck on closed then it will stop the combustion cycle and cause the bike to jolt? Thanks

@GicaPhp

8 ай бұрын

if it will restrict air flow, yes, it will cause drivebility issues

Hi mate , inside my servo , it seems like something is melting as its getting hot and smells like burning plastic ? Any idea ? What could be melting inside ? Thanks dude

@GicaPhp

6 ай бұрын

You will have to strip it, it could be the connectors

I got this error code but I have a scorpion full system so that’s removed I guess that’s what’s causing the code? Clear the error and carry on as usual?

@GicaPhp

2 жыл бұрын

Yes, clear the code, if fault reoccures you will have to look into it

very nice, its good to know how to get the C failure codes, do you know where i can find all the failures maybe?

@GicaPhp

3 жыл бұрын

C11 - CAMSHAFT POSITION SENSOR C12 - CRANKSHAFT POSITION SENSOR C13 - INTAKE AIR PRESSURE SENSOR C14 - THROTTLE POSITION SENSOR C15 - ENGINE COOLANT TEMPERATURE SENSOR C21 - INTAKE AIR TEMPERATURE SENSOR C22 - ATMOSPHERIC PRESSURE SENSOR C23 - TIP OVER SENSOR C24 - IGNITION COIL SIGNAL #1 C25 - IGNITION COIL SIGNAL #2 C26 - IGNITION COIL SIGNAL #3 C27 - IGNITION COIL SIGNAL #4 C28 - SECONDARY THROTTLE VALVE ACTUATOR C29 - SECONDARY THROTTLE POSITION SENSOR C31 - GEAR POSITION SIGNAL C32 - PRIMARY INJECTOR SIGNAL #1 C33 - PRIMARY INJECTOR SIGNAL #2 C34 - PRIMARY INJECTOR SIGNAL #3 C35 - PRIMARY INJECTOR SIGNAL #4 C36 - SECONDARY INJECTOR SIGNAL #1 C37 - SECONDARY INJECTOR SIGNAL #2 C38 - SECONDARY INJECTOR SIGNAL #3 C39 - SECONDARY INJECTOR SIGNAL #4 C41 - FUEL PUMP CONTROL SYSTEM (PUMP/RELAY) C42 - IGNITION SWITCH SIGNAL (IMMO) C44 - LAMBDA C46 - EXHAUST CONTROL VALVE ACTUATOR C49 - PAIR CONTROL SOLENOID VALVE C60 - COOLING FAN CONTROL

@FunCircUS

3 жыл бұрын

@@GicaPhp thanks man, appreciate it!!

Which position have the valve when the bike is off? Open or closed?

@GicaPhp

3 жыл бұрын

Open.

@gmhage

3 жыл бұрын

George, For the first set up, just keep valve full open (default position due to spring) and adjust the cables as you mentioned, right!? BTW very nice video, very helpful. I just subscribed!! Tks friend!!

Hey, I have same code but - is on the top is it different?

@GicaPhp

6 ай бұрын

What do you mean?

Hey I got these and the cables that were attached to the spring are stuck like pulled up, any idea on how to loosen it back up again? This happened because I disconnected it from the spring and turned the bike back on. Thanks in advance

@GicaPhp

Жыл бұрын

the motor should open and close the flap. you will have to disconnect the motor side, as the cables are not sitted correctly and they got stuck inside

@user-cl5ff7ez2r

Жыл бұрын

@George Moraru Its weird because even in the motor side the cables have no room to play, its tight and stuck on both the motor side and where the valve on the exhaust its connected

@GicaPhp

Жыл бұрын

@@user-cl5ff7ez2r you need to strip it down, and you'll see

@user-cl5ff7ez2r

Жыл бұрын

@George Moraru I took off the gas tank, seat and side fairings. On the motorside where the cables attached its stuck with no room to play, also down where the cables attach to the exhaust

@GicaPhp

Жыл бұрын

@@user-cl5ff7ez2r Can you move the flap by hand just enough to see if it is seized in the axe of the exhaust?

If I want to do this fuse wire at home what amp fuse is on it please?

@GicaPhp

2 жыл бұрын

5 Amps will do just fine

@joealex1700

2 жыл бұрын

@@GicaPhp thanks George for this great video I did check the code on my bike and it was code 00 with the throttle sensor off,just a small adjustment and I was ready to go. Keep it up brother and thanks again.

I unseized the exhaust valve but not the cables are stuck!! I can't believe you didn't include on you video how to sort the cables out...

@GicaPhp

Жыл бұрын

I am sorry about that :(

@leewilson4680

Жыл бұрын

How did you get the cable released amyrobson5369?

@Aimless5369

Жыл бұрын

@@leewilson4680 i didn't! I ended up knackering the motor! Because this video didn't explain how to release the cables...So I decide to keep the valve open and install a servo eliminator

@leewilson4680

Жыл бұрын

@@Aimless5369 thanks for replying. Not sure if this was right or not but I managed to pull the cable down through a combination of turning the key to make the valve motor kick in and pulling the stuck side when it did it’s thing. That worked and gave me enough slack to reattach it. 👍🏼

How to on the abs???

@GicaPhp

3 жыл бұрын

Same procedure.

Minha moto deu cód -c42

@GicaPhp

2 жыл бұрын

it looks like your key has failed or the immo system

Teria como me ajudar

@GicaPhp

2 жыл бұрын

how?

why would you tell people to activate the motor when not connected! its completey pulled the cable through one side and ive been unable to get it in the right position !

@GicaPhp

Жыл бұрын

I have not told anyone to do anything, I just shown what I did and you use the information as you find fit. Are you going to jump in a well because someone said so?

@richie5849

Жыл бұрын

@@GicaPhp you said now is a good time to check the motor operates fine when disconnected but it actually seems to mess it up instead, mabye its better to connect cables first then check at end once connected, i have had to take back out my motor which was a nightmare and take off the motor gear to put cables back in right position but i dont know if i have ruined the motor in the process because of this!, i think i may have flat battery now so will find out tomorrow, besides that a helpful guide

@GicaPhp

Жыл бұрын

@@richie5849 you can always power the motor externally and move the cable

How to clear the code ?

@GicaPhp

6 ай бұрын

The code should clear itself