SUR-RON WIRING HARNESS EXPLAINED | SURRON DIY BUILD FROM SCRATCH
Автокөліктер мен көлік құралдары
Describing all wiring harness connections for the Surron light bee. This will be part of my upcoming full build video - building a 25kW, 80v Surron from scratch. Note I am using the EBMX X-9000 controller, so some connections are different than from stock.
Пікірлер: 28
Hey man THANK YOU for this video. I am going in blind trying to repair someone's SurRon X that had no throttle response. Found a couple sheared wires on a mystery connector by the motor and hey guess what: Hall Effect Sensor connector. Much appreciated!
@CoolWatts
Ай бұрын
Great to hear!
Omg amazing vid this helps my horn problem a lot! Thank you dude! EDIT: I also found your review on Ali rn. Great job!
@CoolWatts
4 ай бұрын
Thanks very much. I'm currently editing the full Surron build video, it should be published in a couple weeks.
@Backtrap1943
4 ай бұрын
@@CoolWatts Can't wait to see it!
how great is this 😍
@CoolWatts
Ай бұрын
Thanks! Glad it helped 😁
Thanks had the key and headlight mixed up on accident this helped!
This helped a lot man I really appreciate it
@CoolWatts
3 ай бұрын
Awesome, thanks!
Dude.. I love you.
Really helpful video
Great video! Really helped me with my edirt bike build!
@CoolWatts
4 ай бұрын
Awesome! Thanks
@edsters
4 ай бұрын
@@CoolWattsYou're the only guy that I have found that did this! I'm actually trying to figure out how to get a dirt bike sproket on. Do you have any tips on that?
thanks you this helped alot
Great video btw Is there away to extend the plugs that goes to the controller? Thank you..
Hello, maybe you could help me. I want to install a new taillight, it has 5 cables, 2 is for signals, 1 positive, 1 negative and 1 for the brake light. the signals I don't care about, the positive and negative is obvious, where do I need to add or to weld the brake light for it work when I'm pushing the brake levers?
Hey coolwatts! I was hoping you could help me. So I’m using all surron wiring for a non surron build. And had a question. The “battery in” connector the small grey one. Is that connector the equivalent of positive and ground ring terminals to give the harness power?
@CoolWatts
3 ай бұрын
Hi, yes, that is battery voltage in. 60v, 72v, 80v, etc.
@tritzzy
3 ай бұрын
@@CoolWatts you just saved me so much time wondering why my harness wasn’t receiving power lol. Thank you and your finished build looks awesome!
Where did you get the frame??not available in Scotland
@CoolWatts
3 ай бұрын
AliExpress, all links are in pinned comment in my full build video
Does this still have the green loop to cut to derestrict the bike? by the top of the battery
@CoolWatts
6 ай бұрын
I didn't see it on the new harness I got, purchased from Ali 12-2023.
@shawsie9462
6 ай бұрын
The sleeve that covers all the cables looks tighter and made of different material then the harness that comes on a brand new bike, I have ordered the same harness as shown in this video, but I am concerned it will restrict my bikes top speed again
@Backtrap1943
4 ай бұрын
@@shawsie9462 if so, you just cut the wire again or connect a clamp with wires cut.
What’s the link to that ali seller you purchased this from ?