Strip Paint From Wood With an Infrared Paint Remover
Stripping paint from wood without chemicals using Speedheater Cobra. Removing paint from wood is never an easy chore. Lead paint dust and chips are a concern.
I had lead paint that was chipping and starting to come off in small sheets down to the wood. Covering up the wood with aluminum was an option, however, I live in a humid climate. The wood would have to be sealed up prior to covering it up.
I explored many options, chemical paint removers. Too dangerous, time consuming and messy for me. I looked at paint shavers, but misuse can cause damage to wood and they only work on large flat surfaces. One of these shavers would be hard to hold above my head to remove paint from my porch beams.
I settled on Speedheater's Cobra hand held Infrared heater to remove the paint. While it only heated a 3.75" x 3.75" inch area, it only weighs 1lb 5 oz. I found that it quickly heated up many coats of paint that could be scraped off quickly. There were no little paint chips to stick to the bottom of my shoes. There were small chunks of paint which landed on my tarp. I could pick up the tarp and quickly slide the chunks of paint into a plastic bag.
Пікірлер: 22
What a job! It sure took a lot of patience to get it looking so nice. Pretty masonry flooring entry way too. Thanks for showing your hard work.
@Know-How-Now
2 жыл бұрын
For sure it was a lot of work. When I moved into the house most of the slates on the porch were loose. I removed all of the slates, numbered them, drew an outline around each slate, then set all of them back down. It was a job! The masonry on the walls of the porch is coming off the block. On my list is to fix that. I doubt there will be a video for that. I can get it done, but don't think I know enough to give advice on that.
A thumbs up is also always well deserved. Thanks again!
@Know-How-Now
2 жыл бұрын
You are welcome. Thanks for watching the videos and taking the time to comment.
You’re amazing!! Melvin too! That’s tough work. The end result looks fabulous. 👏🏻👏🏻
@Know-How-Now
2 жыл бұрын
Thanks for the compliment, Mario. I wanted to keep the original look of the house and couldn't bear to cap the wood with aluminum. The wood around the windows is capped with aluminum and after 20 years the powder coated paint on the aluminum is peeling off. Nothing lasts forever. I am very pleased with the results. Melvin was angry at me. He kept trying to go under the tarps. I didn't want him to get in the paint chips. I put him in the house... as revenge he came back out and went under the tarp again!
@MarioDallaRiva
2 жыл бұрын
@@Know-How-Now They always get the last word 😸 You do great work!! Nice house. Btw I recently bought a Craftsman version of your dad’s old mitre saw.
@Know-How-Now
2 жыл бұрын
My brother and I share the mitre saw. I recently looked into the saw and noticed that there is a Craftsman version of it. I think Dad would have bought the saw for when he was installing kitchens. It was amazing to watch him work, he made carpentry work look easy.
@MarioDallaRiva
2 жыл бұрын
@@Know-How-Now Sounds like your dad was a real pro! I bought the Craftsman at Rona aka Lowes which carry the brand now. It beats lugging around the Bosch compound mitre saw that weighs a ton! I look forward to more videos. I’m waiting to swap out a 1940s single pane wood window in the kitchen with a picture window from Home Depot. Lead time is nasty these days of course! Look forward to not installing the window film in the winter to stop drafts and condensation. 👋🏻
@Know-How-Now
2 жыл бұрын
When I was growing up, we never hired anyone to do work. My dad built our first house and did almost all of the work. He worked for a home builder for a while, I am sure he did more than the carpentry work. I know he contracted the brick laying and plastering to someone. Best wishes for the window replacement.
glad that is outside. heat releases lead fumes.
@Know-How-Now
2 жыл бұрын
The heat range of the Infrared heater is 200-400 degrees Fahrenheit. Lead in paint vaporizes around 1100 degrees Fahrenheit. As mentioned in the video, a heat gun would likely be around 1100 degrees. I wore a respirator... who knows what else may be released when paint is heated.
Great video. I am considering getting this IR paint stripper to do the siding of my 1882 home. When you mentioned that the heat gun is probably more of a fire risk, is this mostly because it would blow the heat into cracks etc? I was hoping the cheaper guns would be ok, if used at the lower temp settings. Thanks!
@Know-How-Now
Жыл бұрын
For sure you could try the heat gun at a lower temp. I suspect it might heat up a smaller area and take longer. The other plus I found it that the paint came off in large clumps making clean up easy. I was concerned about lead getting onto the ground around my house. If you are doing siding, the company that makes the small hand held model I was using, makes a larger model for siding. It's kind of heavy. I saw people rigging up a system to hold it up and slide it horizontally along siding. You could always buy the IR stripper, use it and sell it on eBay after you are finished with the job. I thought that I would sell mine, but liked it so much that I am keeping it. So far, I stripped an interior door and a bunch of solid wood doors from a kitchen that was torn out..
@markanthony3991
Жыл бұрын
@@Know-How-Now Thanks so much for the input!!
@Know-How-Now
Жыл бұрын
@@markanthony3991 You are welcome. It's not easy work, though the reward is that every day I get to enjoy the beauty of the porch. Best wishes for your project.
Great job! I was on your other vids on how to replace and or fix electric stove coils. I went to see my coil connectors and saw they each have 4 your vids show 2 per element. Any suggestions? Love Love your channel. Cheers from S. CA
@Know-How-Now
2 жыл бұрын
Is it an old stove.... from the 1970's or earlier?
Hello
@Know-How-Now
2 жыл бұрын
Hello to you too! Thanks for watching the videos.
@abdel-hadikaddour8400
2 жыл бұрын
@@Know-How-Now thanks