You’re not only great a blending color on woods and restoring but you’re educational as well. Thank you.

@MadManRestorations

11 ай бұрын

Thank you. That's why I started making videos. There are very few channels that show how to properly refinish furniture.

I've been using Citristrip for well over a decade mostly because its low VOC (better for the environment and I can apply it inside), easy to apply (I like that it's a gel) and its ubiquitous at Home Depot. But a few years ago, I noticed the consistency of it was suddenly a bit different. The thing that made me first notice is was that I actually use it to clean brushes dried hard with latex paint, and I used to be able to just rinse them clean with water before after the stripper had done it's job. Now the Citristrip is a bit stickier, which theoretically should be better, but it doesn't appear to be water-soluable like before, so now I have to use odorless mineral spirits or Krud Kutter to "rinse" the stripper, and it usually takes like 5 days soaking in Citristrip to get the brushes clean instead of like 1. It turns out that the old version of Citristrip used to contain NMP, which is why it actually worked _and_ was water-soluable. But an EPA ban went into effect around 2018 or so. A couple references here: www.lumberjocks.com/threads/citristrip-no-longer-works-grrrrr.306812/ www.nrdc.org/press-releases/home-depot-be-third-major-us-retailer-ban-deadly-paint-strippers

@daviddaddy

Жыл бұрын

It's actually not better for the environment. Read the label and compare it to other paint strippers. It's basically the same stuff.

@jillserrao2103

9 ай бұрын

I use water and ammonia for brushes, even with they are almost stiff, and it works great! I put hot water in a plastic container, then add the ammonia. You don't have to use too much of the ammonia. Sometimes (okay, mostly 😂) I get sidetracked and don't clean the brushes right away. Really doesn't change it. Give it a try. Works well.

@tweetlbug

3 ай бұрын

Try putting hard brushes into a 50/50 with Murphy's oil soap and water. Let it soak, it takes a while, but it works and is totally safe to do indoors.

@Nevaloud

Ай бұрын

Yeah the EPA strikes again. They ruined paint stripper I had to get a special account just to get the one with the "bad stuff"

@DJBryanDavid

Ай бұрын

Brushes in oxyclean dissolved in water after chems works well too. Water that’s a bit too warm potentially defects the glue binding the hairs in the heel😉 Just sharing knowledge that was shared with me. Not saying it’s the right way

THANK YOU! I have awaited a video demonstrating exactly this.

Years ago i played with the original Citris-trip and found that it's more of an oil-based stripper, where upon coming across disgustingly old, worn out furniture, it actually helped the old dried out wood grain. yes it darkened the wood, BUT so does any finish. One of the old classical wood finish techniques uses Boiled Linseed Oil as a pre step to finishing the wood, where it requires a long period for the oil to solidify. A great step that brings out the iridescence of certain woods like Mahogany and Curly Maple, but also conditions and helps preserve the wood in or for the long run. This is where, i found, the beauty of using Citristrip ... primarily for the neglected, worn out, old timers ! My latest experimental escapades has led me to a new favorite for stripping all the rest. Just as you found here with your experiment, i love this new solution from Gary at Stripwell. My toying with the products application was the opposite, i brushed it on in several thin coats, {since it was a vertical slant.}....waited and scraped...then scrubbed...then rinse-wiped clean. What a wonderful miracle product ! Not caustic, nor overly smelly ! Really has become a favorite for old classically finished wood. { Meaning, don't know how it would work on Polyurethane types.} Thanks for a great demo-video. Really appreciated this....especially love seeing a great classic table ❣

@MadManRestorations

10 ай бұрын

Thanks for the kind words ☺️

Thank you for your video. A note: mineral spirits are very toxic and you should wear gloves, eye protection and a respirator when using. I'm afraid others will watch this and assume mineral spirits are non toxic.

@michaelweller5470

10 ай бұрын

😬 well that’s bad news

The best I've seen on this. I watched someone else brag about citrus strip but I kept wondering why the wood looked darker and thought it was just my mind. This explains allot.

@MadManRestorations

Жыл бұрын

Thanks! I'm glad you learned something.

Thanks so much. I have a bedroom set from the 70’s that I have been wanting to strip, but it has lots of “nooks and crannies”. Also I need to do the work in the room that it’s n. This will be perfect for the job. Thanks so much for your research!🙂

@MadManRestorations

Жыл бұрын

Glad to help.

Just so you know, if your varnish is thin, the QCS Stripwell works great, but if it's thicker, it's best to use Klean Strip or something else. You also end up using a ton of the product, and at $37.95 a bottle, plus $7 in shipping, it's definitely a costly investment.

@MadManRestorations

10 ай бұрын

I understand the issue of cost being a turn off for some people. But if you refinish furniture as much as I do you value your time and ease of use. A quality 3 stage turbine sprayer can cost almost $1,000. It cost money but quality tools like QCS are worth it when you need it.

@bonneymac38

9 ай бұрын

It’s worth it when it works so great!

Thank you for this video! I would never have found QCS Stripwell without it and for me, that stuff has been a miracle. I'm refinishing two 8' solid mahogany doors and sidelights that had a thick layer of cracking marine varnish and the Citristrip was getting me nowhere. Enter QCS and their great customer service and I'm well on my way. Even though this isn't the application the product was made for, and it's taking multiple passes and lots of scraping, I don't mind spending more to use a product that doesn't take my breath away and isn't caustic. QCS is the real deal, and your demo was so helpful.

@MadManRestorations

3 ай бұрын

Wow that's great. I never thought a video would have such an impact. Thanks! 😊

Buscaba un video así , con una excelente explicación. Muchas gracias. Por fin se que usar y cómo usarlo 👍

Thank you for this video! It was incredibly helpful!

Thank you so much for this review!!! I have an old door I'm needing to strip as well as a chest of drawers and a table! I ordered using your code! Again, many thanks!!❤❤❤

@MadManRestorations

Жыл бұрын

My pleasure. I'm trying to put out useful information for refinishers.

Soooo helpful! I’ve done very little stripping finishes, and am glad to see the product comparison. I was very concerned about fumes, and stripping detailed woodwork. Thanks for taking the time to share!!

@MadManRestorations

Жыл бұрын

Glad to help.

I recently used QCS and found it be a treat to remove finish with. It was so easy to use and had the best results. It’s pricy (shipping is the main problem) so I will buy larger quantities to offset that cost. Thanks for a terrific comparison.

@MadManRestorations

Жыл бұрын

Glad you like it. I agree with buying in bulk.

@myrnaloy4275

Жыл бұрын

Will this strip varnish from the floor?

@adjustableWench

5 ай бұрын

@@MadManRestorations i have the same question as myrnaloy - curious about applications on wood floors as im a wood floor refinisher and we occasionally get customers who want us to sand floors that have old mastic or glue on them. we used to sand them but turns out it gums up our machines pretty bad, enough that we have to send them out to be cleaned and it gets to be kind of cost prohibitive doing that, plus we're down a machine for however long it takes to get them back. so wondering if this would work for something like that

@MadManRestorations

5 ай бұрын

@@adjustableWench I'm not sure. It wouldn't hurt to try. I think most floors use polyurethane. But you would have to scrape and wipe the the residue off or that will gunk up the sander too.

@adjustableWench

5 ай бұрын

@@MadManRestorations these days i would say its about half and half whether its actual oil based poly or a waterbased product but what im referring to is older houses- most recent one is about 100 years old and while i doubt the carpet is that old it did have some sort of adhesive left behind. we tend not to want to sand that as it clogs our machines and gets all over the wheels and gets expensive having to get them cleaned - so its advantageous to have something to get that stuff off before we sand

well i’m glad i saw this video. i was about to buy citrus strip lol i just ordered the 8oz sample size of QCS with your coupon code can’t wait to try it out

@MadManRestorations

Жыл бұрын

Great!! I hope you like it

Wow, great find. I’ll have to give the QCS a try!

@MadManRestorations

2 жыл бұрын

It's a learning curve compared to box store gel strippers. But once you get used to it you can't go back to old strippers.

This was such a helpful video! Thanks so much. New sub here!

Thank you so much for doing this video. I really appreciate the the information. And you’ve saved me a world of hurt. Thank you 🙏 😊

@MadManRestorations

3 ай бұрын

You're welcome. That's my goal of making videos 👍

I'm a rookie and grateful for the video. I'm wondering if QCS is the best product to clean the stain from my sun-cooked front door with intricate etching so I can restain it.

@MadManRestorations

Жыл бұрын

I would use QCS on that. Especially if it has a bunch of grooves in the door. So much easier using QCS than a regular gel stripper.

Very unhappy with Citistrip. It left splotches on my dining room table. I’ll never use it again. Other products have not darkened or left splotches on previous projects.

I've used citrus strip only on solid wood pieces, wrapped in plastic overnight, and never noticed any problem with darkening. (Usually take it outdoors to hose it off while scrubbing with a stiff nylon brush.) It's not perfect but if I found some QCS I might give it a try.

@MadManRestorations

Жыл бұрын

www.stripwell.com/#/

would this be useful for old interior solid wood doors that have been painted (possibly several times)? I'd like to strip the paint and stain them.

@MadManRestorations

Жыл бұрын

It could. It's worked in painted pieces for me. However, who knows what kind of paint is under there. It could be lead paint. Just be careful.

nice to see the restoration of lovely pieces and thank you for the tips : )

Thank you for the information. I wonder be interested in the results of this test with different types of paints and finishes.

@MadManRestorations

2 жыл бұрын

I personally had similar results with painted pieces. But I deal with mostly old lacquer finishes.

Does it work on any finish ?? Will it remove the old wood stain finish back to bear wood ?? Is there anything that will do that beside sanding it ???

@MadManRestorations

2 жыл бұрын

I will be trying it on a Polyshade finish next. I have not tried on stained wood. But it definitely wouldn't hurt to try it.

My dad still to this day over pays others to do stuff, my grandfather (mom side) made stuff and repairs in his garage, I definitely was influenced

I have 4 bottles of QCS. Previously I used Citristrip in an attempt to remove the paint from the window trim, and it dried out. Do you think that I can use the QCS to remove the dried out Citristrip?

@MadManRestorations

Жыл бұрын

Absolutely!

Thanks for sharing. I wonder if removing it initially with the steel wool, on all 3, would work better with the other 2?

@MadManRestorations

2 ай бұрын

I wanted to follow the directions provided by each company. Klean Strip and Citristrip do not say anything about using steel wool.

That QCS was surprising. Something nonhazardous that actually works. Cleanup with regular stripper is a mess. I'll definitely be checking out QCS.

Oh woe is me…woe is me! I have a quart of citristrip in my basement! I won’t use it anywhere near wood projects now! I guess I’ll use the rest of it to strip old paint from painted-metal projects. Nice comparison…I can’t help but feel that it must have been a pain to get the three sections looking the same. I personally HATE veneer, but that table is gorgeous. So nice job on your presentation.

@MadManRestorations

Жыл бұрын

Thank you. I ended up using QCS on the whole piece to even it out.

For stain removal i used a scrub brush and liquid sandpaper. Wipe off residue immediately with a paper towel and let dry. Maybe even dry in the sun. Works beautifully.

@MadManRestorations

8 ай бұрын

Removing stain is different than removing finish. Stain is in the wood. Finish is on top of the wood.

@meme-du8xj

8 ай бұрын

@@MadManRestorations Liquid sandpaper also removed the finish for me. But for things that the liquid sandpaper can't tackle there's The Easy Off method: 1. Make sure your using EASY OFF. Some of these videos are using just “oven cleaner”. I don’t know if this makes a difference but I don’t want to find out. 2. Make sure you’re using the Heavy Duty (yellow can). Some of these videos are using the regular strength (blue can) and claiming it’s not working so well. And apply it good and thick. Wait 30 minutes. I buy from Home Depot or Lowes because they carry the bigger cans that grocery stores don’t carry. 3. MOST IMPORTANT: DON’T USE WATER TO WIPE OR CLEAN IT OFF !!!!!! I saw one of these videos say to scrub with soap and water and rinse with water. In the video, her table was visibly warped afterwards (which she didn’t bother to mention). When I tried this, the wood began to warp AND crack. Wood and water NEVER get along. After 30 minutes, wipe it off with a dry rag. The paint will just smear. Don’t worry and don’t bother wiping/scrubbing too much. Wipe top layer and let it be damp/tacky. Then use a wire brush to gently scrub AGAINST the grain. The paint should crumble off like eraser shavings. When I scrubbed WITH the grain, it started digging too deep into the soft parts of the wood. You may need to do a second application at this point. Wait 30 min. Wipe. Then gently scrub. 4. Now clean the wood with pure acetone. Gently sand with 400 and paint or sand.

@MadManRestorations

8 ай бұрын

@@meme-du8xj I'd be concerned about the chemicals that are in easy off penetrating into the wood. But to each their own.

Would the QCS work on vertical surfaces? I want to refinish all the woodwork in my home that has worn old varnish on it. Tried Citristrip and the other stripper you used and it just made a gooey sticky mess.

@MadManRestorations

Жыл бұрын

Yes! It works surprisingly well on vertical surfaces.

I recently bought 17 custom wood doors and drawers for several bathroom cabinets. They were manufactured with solid hard maple and finished with a driftwood stain and pinstripe glaze. The doors are beautiful but the stain color is too dark to match the other bathroom decor. I don't want to spend another $3K to remake. I am considering refinishing them myself. Would you recommend removing the stain/finish with QCS and then re-finish like new wood? I am an experienced DIYer, but never attempted stain removal. Any advice?

@MadManRestorations

8 ай бұрын

You can definitely try that. If they are indeed solid wood you can sand without going through veneer. However, maple does not stain well and usually ends up blotchy. You may have to use toners of you want to adjust the color.

I have a mahogany table with open wood pores that's been spray painted black . The strippers get the main paint off but not whats in the pores. Any way I can get them clean too? They are very thin, and probably not deep.

@MadManRestorations

Жыл бұрын

I usually use lacquer thinner and a brass brush.

What happens if it the orange stripper dries? I just used for stripping our 100 year old front door. The wood is rougher and has more grain than a nice piece of furniture. Like it wasn't sanded and as smooth as furniture would be sanded. . I'm thinking of applying another coat of orange strip, since I have it, but how do I get it out of the grain. Does that make sense? Thank you for the great video. Oh and does the QCS work on acrylic paint as well?

@rachelmunnerlyn8149

2 жыл бұрын

If Citristrip dries it can be really hard to scrape because it hardens like a chalk. Simply pour some mineral spirits on it with a rag, brush or spray bottle until it’s wet again and then you can scrape it back off because it activates it again!

I so apriciate this video, thank you! :)

I have never tried QCS but I had the other 2 brands. I was taking the finish off of 2 bathroom cabinets, preparing to paint them. I tried Citristrip and and didn't like the results. So I bought some Clean Strip, and it worked GREAT. I had results similar to yours. I agree, I would never use Citristrip again.

@MadManRestorations

5 ай бұрын

We should start a movement to remove Citristrip off shelves 😆

Does the QCS remove paint? I'm stripping an old built-in buffet with several layers of old paint, which do you recommend?

@MadManRestorations

Жыл бұрын

If it's an older paint job I would use something like Klean Strip. But if it's a recent spray paint or latex paint QCS should work.

I used citri strip 4 months ago, and then a few weeks ago on two different items. Turns out, I'm super allergic to it. I barely got a drop on my skin, and within hours hand my hands sweel, turn bright red, crazy itching and the hives all over. Once that gaze was done, the skin on my hands spent days peeling off. I didn't realize it was the citri strip the first time, or I would have never used it again. Now I'll only ever use smart strip.

@MadManRestorations

2 жыл бұрын

Wow, that's awful. It could have been worse. But at least you know now to stay away!

@GlendonFrank

Жыл бұрын

Using Citristrip gave me hives and burning... I'm done with that.

How do you fix a blotchy strip after using citristrip? I just found this video. I already stripped twice with citristrip and there's a few areas that where left blotchy and some of the old laquer still on. This is a 100 old chair that I bought on an estate sale very solid but with a very deteriorated finish. Must of the finish came out nicely after citristrip, mineral spirits with wire wool, and washing with a little water with dish soap. After letting it dry in the hot sun of a summer in Texas I noticed that there's still old finish attached, and a very blotchy backrest. I applied the stripper again and it didn't do anything more. How can I fix the blotchiness left by the stripper?

@MadManRestorations

9 күн бұрын

@@lmgorbea1 don't use soap. You can strip with another stripper. A lot of chairs are solid wood. If that's the case you can just sand it out.

@lmgorbea1

9 күн бұрын

​@@MadManRestorationsthanks. I'll try that to see if it works.

Did u use the finish remover AND cleanser? Or just the remover? The website is selling it as a bundle with the cleaner. If the cleanser isnt necessary, id rather just purchase more remover. Pleasw advise

@MadManRestorations

5 ай бұрын

This is the finish remover. Cleanser is a new product that was not out at the time of this video.

Does QCS work for stripping on ornately carved furniture piece and table legs?

@MadManRestorations

Жыл бұрын

That's when I would only use QCS and nothing else. Spray, wait, rub with wet steel wool, done.

Thank you for this great video

WOW, great comparison. What can you do to repair the darkening done by Citristrip?

@MadManRestorations

Жыл бұрын

You can use a better stripper like QCS or sand. Just be careful when sanding. You don't want to take too much off.

@zoeyfischer3288

22 күн бұрын

@@MadManRestorations i just used citristrip and put wood conditioner on after sanding. Should i sand again and re strip?

@MadManRestorations

22 күн бұрын

@@zoeyfischer3288 is it still blotchy after wood conditioner?

I’m watching this after using Citrus-strip on an oak table top. I left it overnight with the Saran Wrap and I’m left with dark blotches all over the table. We’re you able to remove the dark spots from your project?

@MadManRestorations

Жыл бұрын

Sorry that stinks. I would strip again with QCS or Klean Strip.

@vivianbooth0105

Жыл бұрын

@@MadManRestorations Thank you so much!

Great Video! 👌🏾

Do you think the QCS would remove a more glossy/factory finish or is it more for antiques with the traditional laquer finishes that have kinda started flaking? I’m in desperate need of removing some shiny gloss. The scraper works ok but very physical on a large piece

@MadManRestorations

2 жыл бұрын

I recently used QCS on a gloss lacquer finish. Same deal. It was too hard for my scrapper but used QCS and it came right off.

I was quite impressed and ordered the product. I am a little concerned about cleaning off the stripper using steel wool. Some think the tiny fibers will get into the wood grain. Have you seen this?

@MadManRestorations

Ай бұрын

That's more common with sanding with steel wool. Not using it like this with the stripper. Besides, after stripper you still need to wipe clean, sand, and wipe again. There's no way steel wool will be on the piece after all that.

Thanks for the great video.

I applied one coat of gel stain on my stair. I did not like the color. Can I use QCS to remove it?

@MadManRestorations

Ай бұрын

Technically stain is in the wood not on the wood like a hard finish. But I have had good luck using QCS to remove stain. Let it sit and scrub with wet steel wool. You will probably still have to sand.

Can I use QCS on refinishing a wood front door without taking it off the hinges?

@MadManRestorations

21 күн бұрын

@@sneidigh QCS works on vertical surfaces. What finish is on the wood door?

A tip: I've found that lacquer thinner works better than mineral spirits as an after-wash. Lacquer thinner will often remove any softened finish that your scraper missed, especially if the piece has a lacquer finish.

@MadManRestorations

Жыл бұрын

I 100% agree. That's what I use. But I followed the directions for this test and they say to use mineral spirits.

@islandblind

Жыл бұрын

@@MadManRestorations I know. Also, I've tried Citritrip too, and I agree with you. It's a waste of time and money.

@MadManRestorations

Жыл бұрын

@@islandblind big facts!

@merryhunt9153

Жыл бұрын

Lacquer thinner is a great solvent, but is DANGEROUSLY FLAMMABLE - can even explode in the can. It should be used outdoors and only as a last resort.

@islandblind

Жыл бұрын

@@merryhunt9153 You're right. It is flammable, so you need to be careful with it and exercise good judgement. However, I've used many, many gallons of lacquer thinner and I've never heard of it exploding in the can, and have certainly never seen it happen. Using it outside is, however a great piece of advice.

Great comparison! Can you use QCS indoors? I have a heavy chest that I want to strip in place.

@MadManRestorations

Жыл бұрын

Yes, you can absolutely use it indoors.

@mikesweeney5685

Жыл бұрын

@@MadManRestorations Thanks for the quick reply. Ordered it from Stripwell and used your 10% discount code. 😎

@MadManRestorations

Жыл бұрын

@@mikesweeney5685 nice! Hope you enjoy it!

The citress wax addiitive made it almost impossible to remove from a metal hvac register. Worked after a few days, but the stuff turned into good that was almost impossible to wipe off. Back to old school stripper.

@MadManRestorations

8 ай бұрын

What stripper are you talking about?

@wiseoldman5841

8 ай бұрын

Citristrip. It actually worked well on the metal after a week or so. Covered the registers and put them into a tin pan with cover. The one you find in the food store for oven cooking. Trying to get the Citristrip off the metal was a treat. It did strip down to metal but a wax like coating remained. I used a torch and cooked the residual off the metal. I just painted with an oil enamel spray. Looks good now. @@MadManRestorations

Thank you for this, just did a small citrus trip job and hated the process as usual- was looking for a good side-by-side with QCS and this was perfect. Thank you!!!

@MadManRestorations

Жыл бұрын

Thank you. That's why I'm here 😊

Does it work on PAINT as well?? Any Sanding required afterwards?

@MadManRestorations

4 ай бұрын

Works well on modern latex paint. You still need to sand. But I did post a video on how to refinish without sanding.

Hi, can you please clarify? In your vid. you state that you can simply use water to clean it. But the QCS company states that after applying QCS finish remover you then must use the QCS surface cleanser. I'm hoping to restore my grandfather's old dark-armchair, which has lots of vertical slats on its back. The chair was on a veranda, thus became weathered by both sun and rain. How would you apply/cleanse the QCS on such an armchair? It has sentimental value to my BIL (but only if restored to orig. color & colorfast.

@MadManRestorations

2 ай бұрын

QCS surface cleanser was not out yet at the time of this video. I still use water for my QCS finish remover cleanup.

@minniyoutubaster

2 ай бұрын

@@MadManRestorationsThanks for letting me know & great video! May be in touch with a pic via your biz. There's possibly areas of surface mold, so can I do 50/50 vinegar/water first? Also is an 8-oz. QCS bottle enough for the chair? Also how would you strip nine vertical slats that are near each other along the chair back? Stripwell hasn't replied to email, and there's only voicemail.

@MadManRestorations

2 ай бұрын

@@minniyoutubaster pictures would be helpful. You can email them to me. Email is in my KZread bio.

@minniyoutubaster

2 ай бұрын

@@MadManRestorations By "bio" did you mean the Trenton locale? If so, I believe i sent you the pics when i posted the above. So did you see the email sent to Trenton?

@MadManRestorations

2 ай бұрын

@@minniyoutubaster madmanrestorations@gmail.com

Have you tried using QCS and then covering it with seran wrap? Maybe that helps with penetration and more cost effective since your loosing less chemical to evaporation?

@MadManRestorations

2 ай бұрын

I have not. Stripwell says it's unnecessary. Plus I think it's a waste of plastic wrap.

@minniyoutubaster

2 ай бұрын

@@MadManRestorationsI'm really hoping you can also advise me with regard to the question i just posted. Thanks.

Can I use QCS on my entry door vertically? I cannot make it flat. Thanks

@MadManRestorations

5 ай бұрын

Yes, I've had good results using QCS on vertical surfaces.

Hello??? the qcs is the only one you used steel wool to remove and you say it worked better, pretty silly. may be better all around but you gave it an advantage , right?

@MadManRestorations

Жыл бұрын

I followed the directions on the package. That was the point of the experiment.

Can I use QCS on Teak wood that was just finished with Dutch Oil? We bought Dutch Oil from WATCO but it was a bad batch and it created black spots on our teak table. The support team from Watco recommended using a paint strip. In your experience, do you think that would work? Thanks for any help.

@MadManRestorations

Жыл бұрын

Most Danish teak furniture did NOT use oil. So you shouldn't either. That is why you got the result you did. I would totally use QCS to remove the oil and possibly the stain. Spray QCS, let it sit, apply more, then scrub with steel wool soaked in QCS.

Something for the curves and grooves of my waterfall furniture!

@MadManRestorations

3 ай бұрын

Yep. QCS is the best for that!

Thanks for the video, really helpful. You didn't mention price though, and QCS is considerably more expensive than the other options

@MadManRestorations

8 ай бұрын

It's a family owned company that makes it in small batches. Of course it's going to be a little more expensive. But considering the benefits and that there is no other product like it on the market makes it a must have in my toolbox.

I used Citristrip on a dresser, let it sit with plastic wrap overnight, and it was completely dried out the next morning. I may have not used enough so the next application, I used a thick layer, with plastic wrap and misting with water, if necessary. It’s good at removing from horizontal surfaces but not so good from vertical surfaces so the sides of my dresser still have stain and veneer on it. And I was using a wire bristle brush too. I’m not doing a third round and will just sand to remove excess veneer and blotchiness from the wood. I don’t know if it’s the fact the dresser was espresso colored that it’s blotchy but I may just end up painting the dresser in a solid color to salvage it which is what I wanted to avoid initially. Waste of time and money.

@MadManRestorations

Жыл бұрын

Sucks. But lesson learned, don't use Citristrip!

@amorgan5844

Жыл бұрын

@Mad Man Restorations citristrip has some use for flat tops that have been painted and works very well for paints. Absolutely sucks for removing finishes. You ever watch mad city modern on YT? He restores a table exactly like this one.

@lateinbloom

Жыл бұрын

Yeah, I agree with this. I've been using Citristrip for over a decade (and I'm about to post a separate comment about that), and I've used it on a ton of furniture projects with good results. I mainly like it bc its low VOC and I can use it inside. But I redid my kitchen and taped the upper cabinet edges with frog tape delicate surface, and the tape removed some of the varnish on the side face of the cabinet. So I thought I'd just remove all the varnish, and re-poly. 3 rounds of citristrip paste and it did nothing. Like legit absolutely nothing. I didn't want to sand bc its too messy or buy another stripper that would have too many fumes. Plus my kitchen renovation was basically done except for that, so I opted to just cover it up with a combo chalk/dry-erase/cord board that I made.

Thanks for posting, great video. Shame i can’t get it here in Spain as the shipping costs are wayyyy to expensive.

@MadManRestorations

2 жыл бұрын

That stinks. But glad you liked the video!

For me, when using Citristrip, once I’ve scraped the excess off you have to follow up with a cleaner to remove the residual. I use a product called Afterwash. I’m doing exterior redwood trim to be painted so I think it can handle the Afterwash which seems like lacquer thinner. Doing vintage furniture I would caution against it since you want as gentle of a product as possible on delicate highly prized items

@MadManRestorations

Ай бұрын

That's another reason I don't prefer the other strippers. They recommend you buy another product as afterwards. Seems ridiculous to me.

Made us buy the strip well and can confirm this stuff gets the job done well.

@MadManRestorations

7 күн бұрын

@@TrentTomas-b6p nice! Glad you like it! 👍

Thanks for the video! The blotchiness of the citristrip bothers me even more; this is really important to know before using it.

@MadManRestorations

8 ай бұрын

Glad you learned something.

Would love to see a video where you remove paint or many layers of paint with similar products!

@MadManRestorations

Жыл бұрын

Just have to find a painted piece lol.

Is this qcs safe for veneer finished furniture as well?

@MadManRestorations

10 ай бұрын

Yes I guarantee most if not all the furniture in your house is veneer.

I used Citristrip and covered my pieces with plastic overnight. When I came back less than 24 hours later and scraped, the goo was liquefied and very dark black leaving my wood extremely discolored. Using Citristrip within 30 minutes caused less discoloration but still some in certain places. In my case, I am painting the wood so it doesn't matter but if I were re-staining, it would be an issue.

@MadManRestorations

3 ай бұрын

I still can't believe they actually recommended covering it with plastic wrap. No liquid should sit on wood that long.

I always scrub with lacquer thinner after using stripper regardless. I also give the furniture a light sanding before applying stripper I feel like it lifts the paint faster

@MadManRestorations

2 жыл бұрын

I generally use lacquer thinner as well. But for this video I wanted to follow the directions for each stripper.

@NYSeaNile

2 жыл бұрын

@@MadManRestorations do you sand before applying stripper ? Would be a cool video idea. Sanding before vs not sanding before

@MadManRestorations

2 жыл бұрын

@@NYSeaNile I have not. But could be a good idea. What grit do you sand with before stripping?

@NYSeaNile

2 жыл бұрын

@@MadManRestorations 180 usually. If its a thick poly like on pianos 120

Was directed to you from someone on Reddit. Your videos are excellent tutorials?, I needed to find your content sooner! Can u tell me how to correct the dark embedded stain/ splotchiness from citristrip on walnut veneer? Sanding further seems risky, I tried oxalic acid but it didn’t work. . Looks bad.

@MadManRestorations

7 ай бұрын

I would try another stripper like klean strip or QCS. Then sand by hand with 150 grit. OA won't do anything in this situation.

Wonderful Thanks

I have also noticed a change in Citristrip. It takes MUCH longer to dry. It never altered the color of the wood before, so I was surprised when I saw dark blotches this time. That being said - I did a little research and the reformulation prevents it from drying out to quickly. The "blotches" still feel damp after 24 hours, but seem to be fading away as the piece (a large cherry table) dries. I'm hoping that once fully dried the blotches will be gone. However I am going to use some denatured alcohol to help break down the waxes in the stripper to try and speed the drying process. I'll update the results when done. I used to be a fan of Citistrip. But this new formula - if it doesn't permanently stain the wood - is no longer a viable solution for me as I cannot - and will not wait extraordinary lengths of time for it to dry.

@MadManRestorations

9 ай бұрын

Yeah. We've all kind of been duped with Citristrip. Give QCS a try!

@harleyroadkingcustom

6 ай бұрын

Update - after several days I just took to re-sanding to remove the stains. They never fully disappeared. I'm definitely done with citristrip. Too bad. It used to be a decent option for me, as I don't have great ventilation.

@justjill894

4 ай бұрын

Mine always lighten up after given some time. Usually a couple shifts at work before I get back to it! 😅

On the stripwell website it says it only works on antique finishes from 1970 and prior. The table I want to strip is from 1980s. Is it going to work? Why wouldn’t it work on a stain from the 80s?

@MadManRestorations

11 ай бұрын

QCS will only guarantee that it works on 1970s and older finishes. In the 1980s some manufacturers started using polyester finishes that are a huge pain to remove. That's kinda why. But if youe table is a lacquer finish QCS should work no problem.

@kevinwalker7392

11 ай бұрын

@@MadManRestorations so to test that do you use the rubbing alcohol and q tip trick to see if stain appears on the q tip?

@kevinwalker7392

11 ай бұрын

@@MadManRestorations I sanded the table top with a mouse sander and there was a white residue that came off before I got wood. I loved how it turned out after adding a tinted osmo hard wax. Would like to make the chairs match. Sanding the ornate chairs will be so laborious to get the stain off.

@MadManRestorations

11 ай бұрын

@@kevinwalker7392 try lacquer thinner. If it removes the finish it's lacquer.

@MadManRestorations

11 ай бұрын

@@kevinwalker7392 stain is color that goes into the wood. Most pieces were finished with tinted lacquer that goes on top of the wood.

Great video, have you ever tried QCS on brick? I tried Citristrip and wasn't happy with the results

@MadManRestorations

7 ай бұрын

I have not. Sorry.

did you actually try the saran wrap or just guessing regarding the results of the sitris strip

@MadManRestorations

Жыл бұрын

I've never done it. Nor do I think it's a good practice. Veneer should not be see that long. I've seen other people do it with horrible results.

@agomodern

Жыл бұрын

Waiting for 24 hours is a joke when other strippers work in 5 minutes.

@MadManRestorations

Жыл бұрын

@@agomodern I agree. But for this test I wanted to give them equal drying time. Plus, I was also busy.

@agomodern

Жыл бұрын

@@MadManRestorations I was referring to the tip with plastic wrap for 24 hours.

What type of brush I ccan use with Klean strip?

@MadManRestorations

10 ай бұрын

I use a cheap chip brush.

where did you purchase the QCS please?

@MadManRestorations

Жыл бұрын

www.stripwell.com

Would you recommend QCS for paint?

@MadManRestorations

Жыл бұрын

I've had good luck using it on spray painted pieces with latex paint. But it's not intended to work on paint.

Ohhhh yes...add more to the others besides the original 😁😁

What will QCS do on painted wood?

@MadManRestorations

7 ай бұрын

I've used it on pieces that have been painted with modern paint no problem. But they don't guarantee that it works on paint because there are so many variables.

I used Citristrip on both latex painted furniture and automotive enamel paint. It completely softened the latex within 30 minutes (rinsed off completely with warm water and scrub brush) and effectively softened or reduced the paint to metal bond of the enamel overnight to be scraped off with a stiff putty knife.

@MadManRestorations

Жыл бұрын

Thanks good. But there are better strippers for wood than citristrip.

@cptcosmo

Жыл бұрын

@@MadManRestorations True, but they are more toxic. Former Journeyman Carpenter turned Architect here.

@agomodern

Жыл бұрын

@@cptcosmo I'll take something hazardous that works better than something nonhazardous that doesn't any day of the week.

How much stripper should you use per 100 sqft??

@MadManRestorations

29 күн бұрын

Uhh I dunno. Just make sure it stays wet.

Nice work...glove and mask up!! Avoid COPD!

Wish i had watched this before i refinished a door for a client... citristrip didnt stand a chance to premium strip, i wanna try qcs. See how it reacts to latex

@MadManRestorations

9 ай бұрын

In my experience QCS works well with modern latex paint.

Bought Stripwell for a window restoration project. I tried it multiple times. It removed basically no paint. Citristrip was more effective (although Citristrip required multiple rounds)

@MadManRestorations

Жыл бұрын

QCS does not claim to remove paint. Even though it has been proven to remove certain paints.

@ericcragun4637

Жыл бұрын

@@MadManRestorations they have updated their website since I bought it. But they still advertise paint stripping as a feature: kzread.info/dash/bejne/p2qDvMioc8WbYJc.html

I had to strip paint from fieldstone (I know you are stripping wood) and did a side by side comparison of Citrus Strip and Klean Strip and the Citrus Strip was distinctively more effective than the Klean Strip, particularly on the 1st application. The fumes from Klean Strip can be caustic even though I had the benefit of working outside. Plus, I accidentally left a smudge of Klean Strip on my arm and never noticed it until later when I ended up with a chemical burn. I don't think I'd ever use Klean Strip again and would opt for Citrus Strip but definitely would try out QCS next time.

I used the strongest version of stripper on a Broyhill Brasilia. Had to set up in a small area with only a few feet to work and set up drawers fronts and cabinet. It was August in South Georgia (hot as f**k) so I was wearing gym shorts with no undies. I bent over to apply the stripper to bottom drawer while accidentally backing into the freshly applied cabinet. My left butt cheek made contact with a saucer plate size of stripper. It may as well been direct application to my butt cheek with the thin shorts only being the barrier. I immediately lost the shorts and wiped off the stripper and nuetralized the area on my butt. Twenty seconds on my skin and it looked like a race car pulled me around a hardwood floor on my ass for a few hours. It must have been 2-3 weeks before I could sit down or wear anything comfortably. Learn from my stupidity ! I’ll be trying the QSC…… On the bright side if things the Broyhill Brasilia Credenza turned out beautiful but it was a tough restore since the thin veneer doesn’t allow for much sanding. Chems was really the only option I knew at the time. I’m starting new Brasilia nightstands tonight. Anybody know of a better option versus QSC or maybe not using chems at all?

@MadManRestorations

Ай бұрын

I pretty much exclusively use QCS on Brasilia because of the curves. It'll make your life a lot easier.

Question: Wouldn't the steel wool scratch the wood?

@MadManRestorations

Жыл бұрын

No. 0000 steel wool will not scratch the wood. This is to remove the finish so it doesn't matter. Using steel wool against the grain in a finished piece may scratch it. But very fine and is easy fixable.

@Coupal1

Жыл бұрын

@@MadManRestorations This video was very informative. Many thanks for the reply.

Dang…. Wish I had seen this BEFORE going through the goopy mess of applying citristrip multiple times to my side table 😢

@MadManRestorations

2 ай бұрын

Ugh. I've been there. I'm so glad I'll never be using Citristrip again.

Where can you buy QCS?

@MadManRestorations

Жыл бұрын

www.stripwell.com/#/ Promo code MadMan for 10% off.

Dude wear some gloves when doing this

@mireyareynoso19

3 ай бұрын

Maybe He is allergic to latex

@cussininthekitchen8224

2 ай бұрын

@@mireyareynoso19then he can use nitrile or leather or work gloves or literally anything. Plastic bags on your hands lmao fr this is caustic you shouldn’t have skin contact with it

Has anyone ever used QCS to remove wood stain?

@MadManRestorations

Жыл бұрын

If heard people have good success with some stain. I will be testing that soon.

Citrus Strip used to be good. But they changed the formula several years ago, and now it sucks. Kleen Strip is good. I use that now.

@MadManRestorations

Жыл бұрын

Me too. Depending on the project it's either Klean Strip or QCS.

I'm having great results using Citristrip Gel and Paste on my cabinets. The secret is to apply generously, then cover the wet areas with food plastic wrap and let it sit for at least 12 hours. I let mine sit for 24 hrs. Then scrape, reapply & plastic wrap, sit 24 hrs, the scrape, scrub hard with a toothbrush and water to clean out the wood pores and neutralize the stripper and wipe down. And no Methylene Chloride. I started with just a quart of the gel to test how it works - I've used traditional strippers before, but they're pretty toxic. Glad it worked for me!

@MadManRestorations

Жыл бұрын

Do not be confused by the smell of Citristrip. It is not really "safer" than other strippers. Cabinets are different than working on MCM veneer pieces. Keeping the veneer wet can cause it to lift off the particle board which is not good. I would never let Citristrip sit overnight under plastic wrap. Look how it darkened the veneer after only 20 mins.

Where can I purchase QCS?

@MadManRestorations

Жыл бұрын

www.stripwell.com

Hmm, I think that if you use the steal wool with clean stripe you will get the same results as QCS.

@MadManRestorations

Жыл бұрын

Possibly but you can't touch Klean Strip with bare hands. Plus I was following the directions explicitly.

Oh my gosh!! I wish I had seen your vid BEFORE using citristrip on my pine table. It looks awful! As per directions, I used plastic wrap, let it “soak” overnight and then used mineral spirits to clean after scraping of and it looks awful!!! We’ve tried to further clean with 91% alcohol and it help a bit. I agree with advice - DONT use especially on pine.

@MadManRestorations

2 жыл бұрын

Ugh. What a nightmare. I can't believe on the directions they say to use plastic wrap. Let it dry and strip again with another stripper or sand carefully to even it out.

@My_sister_crochets

2 жыл бұрын

@@MadManRestorations would you recommend QCS to remove the stains from the table after Citristrp?

@MadManRestorations

2 жыл бұрын

@@My_sister_crochets 100% YES!!

@ShelleB

Жыл бұрын

Me, too! Just yesterday I began the process of removing the black painted finish off a pine coffee table that I picked up on Facebook Marketplace. Did the Citristsrip w/ plastic wrap and the paint came off great however the wood looks orange! I've tried paint thinner w/ steel wool, vinegar & water, Dawn & water, even rubbing alcohol and can't seem to get all of the Citristrip off. When I attempt to sand, my sandpaper gums up within a minute or two. I'm just about at my wit's end. Wish I had known of the pitfalls of Citristrip beforehand.