Thank you so much for this informative video. I’ve always wondered how do these newer X15 Cummins repairs work.

Shit man we like details. Hope you get the likes you deserve man. God bless

great video really appreciate all the details

@dirtyassdieseltech6348

7 ай бұрын

I appreciate you taking the time to watch it.

Thank you great work,we appreciate that

@dirtyassdieseltech6348

6 ай бұрын

Thanks for watching my video. A lot of work goes into making these.

Sounds like it’s gona exsplode. I know what you mean the first time I did that test. I was like wtf this thing gona blow. Hahahhahahhaha

@dirtyassdieseltech6348

Жыл бұрын

I love when I’m teaching a new tech and have them do the test. I had one turn ghost white and shut the test off.

Dang I wish you were in Arkansas 🤦🏾‍♂️ my truck is stuck at 5 miles due to inlet sensor need replaced

@dirtyassdieseltech6348

Жыл бұрын

Was you able to get your truck fixed?

@CantrellMosley1

Жыл бұрын

@@dirtyassdieseltech6348 yes a really good mobile guy came and cleared the derate light and got a forced regen and my truck was back to normal.

I dont have this computer, So can I just replace the intake sensor by myself, without making a computaer test after replace it ? The engine light eill come off?

@dirtyassdieseltech6348

16 күн бұрын

It may turn off cel when truck is started and allowed to run for one minute, if not, it may take 3 key actuations

I have on this truck kenworth 2018 cummings x15 ..codes 3649..3446..3583..I replaced j1 harnesses and j2 harnesses..and the aftertreatment harnesses..and still I have this codes for inlet and out let nox sensors??

@dirtyassdieseltech6348

Жыл бұрын

Those should both run from the same fuse. Check fuse for break, not pop.

@fernandomoran5979

Жыл бұрын

@@dirtyassdieseltech6348 were is the location of the fuse?

@fernandomoran5979

Жыл бұрын

@@dirtyassdieseltech6348 I check all the fuses at the the front..and they are ok

@fernandomoran5979

Жыл бұрын

@@dirtyassdieseltech6348 what's your contact number

Can you help me on how to test the inlet and out let nox sensor. Electrical connector?

@dirtyassdieseltech6348

Жыл бұрын

Check for valid power and valid ground at 4 pin connector. Also check your CAN hi & low. Power should read within a volt of battery Ground should have .1 to 1 ohm CAN hi should 2.5vdc+ CAN low should be 2.4vdc- Resistance between hi and low should read 120ohms on the chassis side and the sensor side. If you install an inline diag plug you should get 60ohms connected

Without video'ing, how long "should" this take?? Remove, replace, and any programming?? Thank you.

@dirtyassdieseltech6348

Жыл бұрын

Diag 1 hour. To replace could be anywhere from 30 minutes to an hour, depending on if the sensor is seized in the port. To verify the repair 30 minutes to an hour. Most shops will charge 3-4 hours.

@bigboatfun

Жыл бұрын

@@dirtyassdieseltech6348 thanks vm. Sounds like I budget for 4 hours to be safe.

What fuse is to,check for the intake nox sensor?

@dirtyassdieseltech6348

20 күн бұрын

@@charlesfroze6724 that will vary depending on model

@charlesfroze6724

19 күн бұрын

@@dirtyassdieseltech6348 KW T680 2019

@dirtyassdieseltech6348

19 күн бұрын

@@charlesfroze6724 not sure about kenworth

How can I contact you?