Start Button Bypass // Talaria Sting R MX4
Тәжірибелік нұсқаулар және стиль
Goggles: amzn.to/41O9ZMp
Helmet: amzn.to/3ACZGiq
Gloves: amzn.to/3VhzYcG
Chest Pack: amzn.to/41uLdR2
+4mph amzn.to/3oq9uth
Gritshift headlight: amzn.to/40rwoO8
ODI Number Plate: amzn.to/3ndnzds
Headlight switches:
Red Toggle Switch: amzn.to/3N0SDHY
Blue LED Button Switch: amzn.to/3H2BWIe
Shimano Brake Pads: amzn.to/41tBfQk
Shinko 241 dual sport tires:amzn.to/41o68FZ
3” riser bars: amzn.to/423dbUv
#talaria #surron #ebike
Пікірлер: 24
Good stuff! Its a strange feature - it took me a good few minutes to get my bike started when i first assembled it 😂
Will this work on the xxx? I’m installing a thumb throttle and have to bypass the start button. Was going to twist the yellow and green wires from the start button together then run a jst connector from the black red and white wires on the thumb throttle to the remaining black red and blue wires on the bike
@freerfixedit
10 ай бұрын
I'm not sure about the xxx, maybe experiment and see, but I can't say cause I don't have the xxx... hope you get it worked out though! thanks for watching!
Would you know how to install a thumb throttle on this bike? I have carpal tunnel and been eyeing out this bike for over a year now. Its time. Great videos! Keep up the good content
@freerfixedit
Жыл бұрын
I haven't done it myself, but I'm pretty positive it can be done because when surronster broke his wrist he put one on his surron... my guess would be just follow the throttle wire down and see if it goes to a connector... if so just get a thumb throttle with that connector and in theory it should work
@freerfixedit
Жыл бұрын
and thank you! I appreciate that!
@MotoAlias
Жыл бұрын
You could definitely do it... they use 3 wires, pos neg and 5v. You most likely won't find a thumb throttle with the same connector used on your current throttle. You may have to wore the 3 wires directly or cut the plug off your throttle and splice it onto your thumb throttle.
@jpwrx199
Жыл бұрын
Woah! Wealth of info pouring in. Thanks guys. This will kick start me! Im ordering mine next week
@freerfixedit
Жыл бұрын
@@jpwrx199 love to hear that!
My bike keeps saying wait but I don’t think it’s anything to do with the sensors I haven’t tried bypassing them yet but I’ve had a new key barrel and it’s only been bad since then if I wiggle the barrel it will sometimes go to ready? Would the key barrel affect the wait/ready thing?
@freerfixedit
4 ай бұрын
I’m not sure if the key barrel would, possibly. Check your connections and make sure they’re good. And make sure the throttle and brake sensor connections are all tight and aligned
@kailumrichards5948
4 ай бұрын
Appreciate the reply I’ll have a look in a bit now
Would this work on the mx3?
@freerfixedit
Жыл бұрын
I don’t see why not 🤷🏻♂️ if it’s the same style throttle with just a simple button switch it should be the same!
Is there a way to undo this process
@freerfixedit
9 ай бұрын
If you do a jumper wire then yeah. Just remove it and there wouldn’t be contact anymore.
Hey, so I just want to confirm that you just use a "jumper wire" right?
@freerfixedit
5 ай бұрын
yeah basically just connect both sides of the switch with the small wire and it will send the signal that it is always being pushed
@samapfel_08
5 ай бұрын
@@freerfixedit nice thanks
Why do this?. You can just turn the key. And prese the start button as soon as the screen shows a T. Which is literally 1 sec. and you will go
@freerfixedit
Жыл бұрын
It was annoying to me. So I did this
@Spacezee110
Жыл бұрын
@freerfixedit you mean pressing the button? Do you have the kickstand sensor removed too. I just like them because it's stops curious people looping my bike trying to get an engine noise lol
@freerfixedit
Жыл бұрын
@@Spacezee110 yeah I removed all sensors. Turn key and go now. But I will say, the one and only time my bike has been dropped was from someone squatting down to look at it after they rode it, hand was on the throttle and looped it 😂
@Spacezee110
Жыл бұрын
@@freerfixedit it's worse indoors.