Appreciated the video content? Want to show some love? Hit the Thanks button under the video or hit up my PayPal tip jar: PayPal.Me/TSGReel

This channel is a goldmine

@TSGReelService

2 жыл бұрын

Thanks for the love! Stay tuned for more ... spread the word about the channel.

What a mess. Makes me wonder what the inside must look like. But you got it going again, nice work.

@TSGReelService

2 жыл бұрын

Thanks Steve! This was recordded a few months back, but I just got around to editing and posting it.... I don't recall how it looked inside, but something's telling me it wasn't that bad inside. Go figure if that's true.

Wow - That was one wicked messed up drag stack! Tad

@TSGReelService

2 жыл бұрын

🙂 it was, but hasn't been the worst I've seen. 🤯

Great tips, thanks for posting.

@TSGReelService

Жыл бұрын

You're welcome and thanks for watching! More vids to come.

Good job on that reel 👍🏼👍🏼👍🏼👍🏼👍🏼

@TSGReelService

2 жыл бұрын

Thanks Jan!!!

For cleaning the crud and corruption out of the drag cavity, spray down with CLR (calcium, lime and rust) cleaner. Allow to sit 10-15 minutes and it will melt away a lot of the salt and aluminum oxide corrosion. Flush with clean water. I've gone to using CLR and a soft bristle brush on the exterior of any of the Penn International reels I've purchased that require a little tender loving care. The Scotch-Brite gray pads are # 7448 pads. If additional cleaning is required in the drag cavity, Dremel sells a small wire wheel that attaches like the rest of their accessories via the 1/8" collet.

@TSGReelService

2 жыл бұрын

Thanks for watching and your input, Gunga. I used to use the CRC Salt Away (similar to the effects of CLR), but found that the results were close to the same as just using the screwdriver and scrubbies. After all these years, I still don't have a Dremel.... think I need to get one, just to try it.... I know it's great for refurbing gears, and I'm sure it'll make quick work of the well. Stay tuned for the next video.

@gungadinn

2 жыл бұрын

@@TSGReelService I'll give your cleaner a try to see if it works the same as CLR. I do use CLR on the coffee pot though. I wish I had taken pictures of a Penn 12T I recently purchased. It had sporadic corrosion spots, and the typical green chrome. CLR with the soft bristle brush removed the corrosion spots and all of the green. Once the nasty grease was removed, vinegar and water on the brass parts and cleaned up nice. Had one bearing that was rough, but for what I paid, well ahead of the game. I needed another rod and reel to leave in my truck for those days too nice to not fish. I refuse to leave tackle in the boat, as things have a tendency to sprout legs.

@TSGReelService

2 жыл бұрын

Lol.... they do have a habit of walking away. If it was that bad, I'm sure you got a good deal on it. I tend to stay away from the vinegar, but CLR does work for a lot of things.

I hope that screwdriver is an extra one to be used as chisel. If I may be permitted to make a suggestion. It would be a good idea to remove all of the trash from the work area, once cleaning is completed and start with a new clean surface to assemble the reel. Thus, eliminating the chance of re-contamination. Otherwise, an informative video.

@TSGReelService

2 жыл бұрын

Thanks for watching, Hashem! Suggestions/comments/feedback/praises are welcome. I had enough clean area to not worry too much about contamination, but it's a good point you bring up (see my other videos). In regard to the screwdriver, heck no.... it's my do-all. With the abuse I put it through, I'm surprised it's still functional (you should see how I use it for frozen Spinfisher bearings). Spread the word about the channel.

@Mahigeer1

2 жыл бұрын

@@TSGReelService As my friend always says------"Biggest room in the world is room for improvement".

Ya your funny peddy people can not do this stuff them selfs that is so easy to take the drag washers off and replace and clean it out boy your my hero I can take that reel apart blindfolded and grease it and replace any parts it needs I would get you to c if my toilet flushes right 😂😂🤣

@TSGReelService

8 ай бұрын

Thanks for checking out the video and sharing your thoughts.

ScotchBrite

@TSGReelService

2 жыл бұрын

Thanks for watching! I think it's called something else. If Joe sees the video, he'll let us know.