I was on hiatus from the drone scene for the past 5 years and already this video is showing me the ropes again. Thank you. I'm also a Spektrum guy so I'm excited to get my hands on the new transmitters

@StevesRC

11 ай бұрын

Glad I could help!

Thanks for the answers. I'm VERY glad Spektrum isn't forcing Android across the line. At the same time, the NX doesn't offer enough to justify replacing my DX9 and DX6. If I had to buy new, I'd likely get a Radiomaster but if I wanted Spektrum brand, the NX10 looks nice.

@RuudyL

2 жыл бұрын

I looks nice, dont buy it

Thank you for the great answers. Can you tell me what the battery charge life is in the NX10 before it is drained when the radio is not used during the winter? My DX9 and other radios have a real snap switch which cuts the power 100%, but the NX10 had a soft touch switch which has a little power being used all of the time. Thank you

Great idea on the nameplate antenna! My crossbar is usually buried in my lap where I rest the radio when I fly. So this is perfect for me!

@StevesRC

3 жыл бұрын

Definitely makes sense!

@leerenslear1064

3 жыл бұрын

good way to get testicular cancer !!!!

How is the new antenna placement any better? When the second antenna were in the handlebar at the back, it was 90 degrees to the primary antenna, which is optimal for diversity.

Question? What is the process to check the charging ability of the battery in the nx 6. I have a new one that has been charged twice and now acts likes it is not charging. Also then, what is the trick for taking the batter out to replace if it is bad.

I was moments away from doing a pre order on the NX 10 today until I watched this video. My excitement bubble was popped when you said the radio doesn't support the new immersion RC ghost system........ Do you have any time frame information of when that may happen that would change my mind and still order this radio?

I purchased a wingnuttech controller for the lights on a radian 2m plane. Trying to find a video on how to set channel 6 on the receiver to the R Knob to adjust the lights on the controller. Any ideas where I might find such an animal?

I’ve had NX6 for month now. Flown many times. I flew week ago. Today I tried to charge it for tomorrow flying. Noticed green light didn’t come on and battery really low. It was 3.2. So I let It charge for awhile and checked it again and it was 2.9. Then It finally went dead. Nothing on screen not charging. I did notice when I stopped charging earlier to check voltage I noticed there was a running time just above actual time. It was like 8hrs and 10 minutes. I haven’t had transmitter on for days so don’t know what that means. What actually is that running time. So anyway what happened? Did I get bad battery? I just ordered the 6000mah upgrade.

Hi Steve just picked up a Nx8 . Question will this radio fit into the spectrum dx9 case??

Random question. What are the little covers above and below the gimbals for?

@StevesRC

4 ай бұрын

That’s for adjusting gimbal tension and stuff

@Commandodesigns

4 ай бұрын

Cool. thanks.@@StevesRC

Is the NX series compatible with the Ar9030T? You did not mention this RX in your video but I do currently use them. Also what about the AR9350?

Thanks for the awesome video! I really like the folding antenna. Can you recommend a more compact transmitter case. Right now I’m using the basic Atomic case with my DX8 G2

@StevesRC

3 жыл бұрын

I've not found one yet, but stay tuned :)

great info I'm getting the 8

Great video. Thank you. Does the NX10 have vibration alerts like the DX9?

@StevesRC

3 жыл бұрын

Of course!!

Excuse me. I have some questions. Firstly dose this transmitter work with Volantex rc,Fmc,and syma aircraft? Secondly I was thinking that with multiple people with me using a transmitter flying 1plane each, I thought of using wireless headsets and make a little Air traffic control tower to monitor our flying. what do you think of this idea? Lastly would it be possible if I reuse the box that comes with a plane or helicopter to make a hanger to store them when not in use?

Do these radios have presets for all HobbyZone models? the sport cub s 2 in particular.

Please help … 😊☺️Which 10 or 12 channel receiver do you recommend to use with this NX10 ? 🤷🏻‍♂️

Hey Steve, just got my NX10. It’s registered and updated, only problem it does not recognize that the SD has been installed. Try to download and it just says No SD card. Have the recommended class 16gb card. Can’t find a solution in the manual. Thanks

Question 1 My NX 8 just says “thumb twiddling” when I hit log in. Just does that until I press the roller or turn it off. I’m already on wifi. Question 2 How do I get my 8020t receiver into safe. I tried Putting in the bind plug then plugging in the battery then unplugging the bind plug and finally binding the radio. The radio does bind,but not in safe mode. Thanks. Great videos a 8020t video would be great. Not a lot out there for it.

can i upgrade my dx6 radio to the most recent airware firmware by spectrum. i currently do not have airware firmware on the radio.

Can you add an instructional Video on how to hook up crossfire/tracer nano to the NX radio?

Hi, do yo know if the AX3X Gyro will automatically work with the model pre-sets you can download for this? I have 2 of them but they are such a fuss to programme I can't even use them. I tried to get my local hobby shop to help but they couldn't work it out either. Thanks

@StevesRC

3 жыл бұрын

AS3X programming is done RX side, not TX. So no, you'd have to download those specific model presets or create your own. Hope that helps!!

I have been wanting to purchase a Spektrum Transmitter for a while now . Glad I waited . Couple of questions for you . I have been using Frsky transmitters among others for quads & airplanes . So here we go . How or where can I find a list of the airplane models in the Nx10 ? Is the list brand specific ? Does the Nx10 support all new & older model receivers & ESC’s ? Is the Nx10 able to use Jr modules ? You stated Crossfire is supported . How is this going to be possible if there isn’t a type of Jr module adapter ? Are they capable of using FPV goggles for drones or airplanes . Is another brand receiver able to plug in for 5.8 ghz signal ? Analog & or digital ? Lastly do you offer any discount codes on receivers if purchased with transmitter . Since it doesn’t come with any ? Thanks

This was great info! I’m looking to get into complex sailplane and trying to decide between dx or nx 8! This helps me a lot making my decision just too bad that not available for about a month

@StevesRC

3 жыл бұрын

The NX10 just started shipping in the US.

@jimmyhaley727

Жыл бұрын

you might want to wait a while, NX series are giving lots of problems, mine keeps getting a red screen warning and it is hard to get it off,, mine is NX8 and with no updates as it was working fine,, updates on PC are usually problems also

is there a place I can buy a throttle gimbal for my nx8 ?

I LOVE YOU STEEEEEEEVE! 🗣️😂

I have received today my new NX8 and i would like to change mode 2 to mode 1 , and i am not sure for the procédure , could you help me to do , Thank you

Steve. I just purchased an NX 10. Virtually the first thing I read when I opened the instructions was a statement on the battery safety sheet that states that it should only be used between 4c to 49c (40f to 120f). I do some winter flying in temperatures down to about -10c. Does this mean I have to use a different battery pack or a different transmitter for winter flying. What are the risks?

@StevesRC

3 жыл бұрын

I flew yesterday for about 20 minutes in 6 degree (F) weather. Risks are low but realize that batteries don't like to be that cold in general. Just like its hard for your car to start on a colder day. You should be perfectly fine, but I wouldn't recommend storing your radio outside and then flying. If you are coming from the car or the house and taking a few flights, you should be just fine :)

@iamtedg

3 жыл бұрын

@@StevesRC Thanks Steve. I appreciate the very fast reply. I will try to be careful, and may just use my Dx6 with a standard lithiam pack if I have to be away from the car for longer. Thanks

I have the NX8. In camber presets. I set the end points at 100% on both ends. I only get 50% of flap and aileron travel. When I max out servo travel to 150% The camber presets travel goes to 75% max How can I change it to get 100% travel?

Could you please show how to get Safe select /AS3X on NX6 and how it operates. I need/want to use it on my Viper.

@CumbersomeDinosaur

2 жыл бұрын

You need a compatible receiver. If so, you go to forward programming and set everything up. If you have a BNF model with safe and AS3X, you need to assign the channels via flight modes.

Question please, sorry if this is the wrong area to ask. Using the NX8 with a AR8360T. I am in the forward programming and its an endless loop of “ did you configure your airplane” hit next and then right back again. I turn the throttle switch off, or on, makes not difference. Can you help with some advice please, thank you

@StevesRC

2 жыл бұрын

I would honestly try a new model file and see what happens. Did you import a model?

Will I be able to have a separate switch for landing gear and one for reverse thrust and other features for my E-flite 80 mm F-16 with the NX8 radio for this jet?

@StevesRC

2 ай бұрын

Of course!

Are all radios set up for an air craft? I bought this from a respected store and he said there is no different to air or ground. Is there a radio that set up just for ground or do I ignore the names and icons of the screen and just set up what I want for my servos. Really disappointed I can have symbols of car or truck and set up related and not an air plane on the screen.

Hey Steve, i picked up the NX10 to fly FPV drones, just wondering about latency will it be suitable for racing?

@StevesRC

3 жыл бұрын

Plenty of Spektrum pilots out there in the FPV racing world. Low latency for sure!

Class 6 SD cards are hard to find. Is sdhc ok? Thank you

Any idea how to connect an NX6 to a DX6 as a wired trainer? The DX6 has the traditional 1/8 inch buddy box cable input jack but the NX6 does not. The NX6 has a data port, USB input, and a 1/8” headphone jack. Does the NX6 need some sort of adapter to 1/8” plug? I wanted to try a wired connection because the wireless connection sometimes dropped out for some reason when the student was in control. Could the dropout have anything to do with the DSMX rate differing on the two transmitters? I think one was 22ms and the other 11ms.

@StevesRC

2 жыл бұрын

SPMA3091 is the part you need. It’s always ideal to match frame rate but it’s unlikely that caused drop outs.

I can not find any ix12’s for sale at all. Do you know the reason why? Thanks so much.

Can I use the battery from my DX8 in the new NX8 I just bought? If so, do I just plug it in ? - or do you have to modify something to get it to work ? Would that give longer use before having to recharge?

@StevesRC

3 жыл бұрын

You can with just by pulling the foam out and plugging in the bigger battery. It would last longer due to the higher capacity.

@lw216316

2 жыл бұрын

@@StevesRC Steve - I don't think you understood my question - I did not ask if a higher capacity battery is available for the NX8. I ask if the battery pack from my DX8 would work in the NX8 - I now know the answer is NO. The connector is different, the bay size is smaller. The stock NX8 comes with a small battery that might get you thru one day of flying. I immediately ordered the pack (3 in the pack). The charging connection is also different. Had I known this ahead of time I would not have bought the NX8. I also don't like that the NX8 using the micro size memory card. The DX8 uses the larger size. The micro is too small - too easy to lose. How are you going to copy your DX8 models to the NX8 ?

i have dx8 one, how do i load my planes into the nx8?? will it work for dx8 one i have been told that it would with dx8 two??

Thanks

Can you tell me why I cannot import models from my sd card on the nx6. When I select import model from transfer card menu, it goes to select file menu and all i see are 2 back folders with no models to select. I know the models are on the brand new card.

@dougrymer4490

3 жыл бұрын

I found that anything larger than a 16gb card won’t work. I am using a 16 and have had no problems.

I was wondering if the nx radios are compatible to buddy box with the DX radios for flight training

@StevesRC

3 жыл бұрын

Absolutely! Via wireless trainer :)

Thank you.

Question. I have had a DX6e for about 2 years after re-entering the hobby. I'm considering upgrading to an NX series TX. Is the NX radio's that much better? Or is it all about the bells and whistles? No issues with the DX6e to date.

@StevesRC

2 жыл бұрын

Unless you’re upgrading for channels, I think you’d be fine sticking with the 6e :)

@papasplanes.956

2 жыл бұрын

@@StevesRC Thanks for the advice.!

So do you need a usb wall charging adapter to charge it with the included cable. Or do you charge it by connecting to a PC?

@StevesRC

3 жыл бұрын

You can do both!

@ronw2316

3 жыл бұрын

@@StevesRC Thanks! I'm getting back into the hobby. The last radio I owned is over 20 years old. LOL! Still works though.

I don't see the Conscendo Evolution as a pre-load to my NX10, even with the latest update. Is it just so simple that I should just go with the manual?

@StevesRC

2 жыл бұрын

Oh yes that model is super simple on setup!

evening sir, i currently have the dx7 gen2, if i purchase the nx10 could i simply take the sd card from the 7 and put into the 10 to transfer all info.? would it really be that simple/

@StevesRC

Жыл бұрын

It should 😁

Hi what's up great video I'm just getting in the hobby what transmitter would you suggest I get for a helicopters and planes for around $400??

@StevesRC

3 жыл бұрын

Check out the Spektrum NX8

Hi Steve when is the nx 10 coming out ??

hi all im looking to upgrade and thinking about the nx10 in the uk and just wanted to know if any knows can you transfere models via link or sd card from a spectrum ix20 to spectrum a nx 10

@StevesRC

Жыл бұрын

You certainly can

Looking to get the NX8, as I have gotten enough life out of my original DX6i(pre DSMX) that I never ended up with a DX6/DX8... Nice to know they do have diversity 2nd antenna... was trying to find that info... One question, Horizon website lists the NX8 with a transmitter strap... but the manual doesn't list this... as the NX10 manual does list strap, as well as stickers(i like stickers)... Does the NX8 come with an all important strap? Another question, I get the charge cord thing, or battery differences... as that helps hit a price point, and lots of folks might buy the cord or bigger battery later, which is $$$ for Spektrum... but dangit, tell them fools to put STICKERS in every single radio and reciever package.... EVERY SINGLE ONE!.... Stickers on our planes, stickers on our crawlers, on our racers and bashers, and on the AUTOMOBILES we drive to and from the field, track, etc... Used to have a Spektrum hat and tee shirt... gonna have to order more swag with my NX radio, and guess I will have to beg a few sticker sheets from the Horizon guys too...lol Lastly... the big difference in the radio itself...between NX8 and NX10... 2 slider switches on the rear, 2 channels, and the gimbals...(not counting battery and charge cable)? Would the gimbals be a huge deal? I got over a decade out of the DX6i that I preordered...kinda want the NX8 for warbirds and just that tiny bit of extra in case I move beyond foam park flyers, etc... but don't see anything in the next decade bigger than like a carbon Z cub, the 1.5m P-51, and planes of that size range... would an NX8 be a good next radio(I have a case these days, so might get a decade out of my next Spektrum radio too)...or with those planes do you see a reason the NX10 would be a lot better...? I don't fly super often, so never wore put a gimbal on the DX6i, I did have to reinforce 2 of the trim tabs though, second time in there I just did all 4 even the ones that still worked fine. Thanks fornthe video!

@StevesRC

3 жыл бұрын

Hey there. I've confirmed that the NX6 and 8 all have straps/stickers. We do have new spektrum clothing coming like in the next few days too available on horizonhobby.com. As far as the Gimbals, you aren't likely going to notice a feel difference and if you are a standard user, the changes of your POTs going bad are very very low. The Hall effect is just a nice touch for the higher end radio. NX8 is the best next step radio that will likely last you a long time. However, I'm always for getting a bigger radio than you need now if you plan on growing up in the hobby and needing more channels. Buy once, cry once :)

I have a question. Can my NX8 use a 2s 7.4v battery instead of the little 3.7 volt it comes with?

@StevesRC

2 жыл бұрын

Nope it cannot

Is this a good radio for a 100cc plane with a 12 channel powersafe Rx?

@StevesRC

3 жыл бұрын

If you need no more than 10 channels you should be good! If not, check out the ix12 and IX20.

Have a nx8 transmitter but won't connect to my dsm2 receivers I've got. Will connect to dsmx fine. I'm in the UK and was reading something about the new nx series won't work with dsm2 ???? Is this true?

@StevesRC

2 жыл бұрын

Yes unfortunately EU versions of the radio are not compatible with DSM2.

Will the Lipo battery in the DX9 work in the NX10? I have one of the first DX9s and bought the Lipo for it, it last for months without charging. I'll probably replace my DX9 it with a NX10 soon. Cheers

@StevesRC

3 жыл бұрын

It will not. Nx is a 1s requirement. Dx had a higher voltage requirement.

@RuudyL

2 жыл бұрын

@@StevesRC Another downer of this so called better transmitter

Any difference between the NX6 and NX8 besides the extra channel?

@marcw201

3 жыл бұрын

I’d like this confirmed also.

Claus G,, Steve, I do have a DX9. When I transfer my planes to a NX10 do the voice alerts come across as well? Thanks.

@StevesRC

Жыл бұрын

They "should" but you may need to add them back in.

@clausgr

Жыл бұрын

@@StevesRC Hi Steve, thanks for your reply. In the mean time I got my new NX10 and yes, voice alerts are coming across but will do a bit fine tuning. All good and happy with the new TX.

Any 10 CH. receivers yet?

Hi! Steve, I have a situation with my NX10 transmitter, I performed a factory reset on the NX10 Radio and it turned on, I turned it off and on again and that's when the TX did not turn on and the problem arose of not being able to turn on, the screen flashes only the logo of Spektrum appears and the Radio does not work for me. Thanks , I appreciate any help . Thank you very much! Greetings!

@StevesRC

2 жыл бұрын

Sorry for the late reply. Have you reached out to product support? Might be something they can help you with. I’ve not experienced this issue before

how do you get the wifi password to save, once I hit back it's gone on the sign in page

My new NX10 froze up and only shows the logo on the screen. Unplugged the battery to get it to power off. What is the solution?

Saludos amigo ✈🤝🏼✈

Hi steve.i purchased a new nx8 a couple months ago. When I first turn on transmitter I get a headset icon on screen with no function on transmitter. When I turn off and back on headset icon is not there and I have function on transmitter. Sits for more than an hour it happens again. Have you ever seen that.do I have a faulty transmitter.

@StevesRC

2 жыл бұрын

I have not seen that. Definitely chat with HH on the site to get it sorted. Odd! Sorry to hear.

@MegaJohnperry

Жыл бұрын

?

What would be really interesting is a comparison of the NX10 to the iX12. The cost difference is huge for 2 channels. Is there enough feature increase to justify the cost ?

@StevesRC

3 жыл бұрын

I can certainly do a video on that! Good suggestion.

I just bought the NX10 and I am bummed that the Crossfire telemetry does not work like my ix12. The receiver works for flying but telemetry for signal does not. I know my quads are set up right because it works with the ix12. Guess I will return it.

I'm having trouble getting my serial number on my NX6

Purchased my NX a month ago from tower hobbies and now it just drains my battery if I leave it plugged in over night ?

@StevesRC

2 жыл бұрын

Sounds like you should get in grouch with support after you try updating firmware

Advertising for variometer does NOT list NX comparability, only references DX??

When I started to think about upgrading to an DX8 I heard something on a stream that made me suspisious. I wrote to Spectrum support and ask if it was about to be replaced in a "near" future. The answer I got wasn't any time soon. Now they release a 10 channel radio and discontiue the DX8. Feel quite cheated.

@StevesRC

3 жыл бұрын

Well our service teams cannot speak about and do not know our future product plans. Sorry you feel cheated. The radio you purchased will service you well for years to come. Additionally, we are still supporting that radio for years to come.

@Daniel_SWE

3 жыл бұрын

I do hope they will have an upgrade deal when get to the stores. A 10 channel radio was what I was looking for but couldn't afford the IX12.

I just got an NX10 and ran into the same Micro SD Card problem. I called Horizon and they recommended no larger than an 8Gb card, lower than Class 10. This size card and class were first introduced 10 years ago. Why use such an old technology... unless the purpose is to do away with a card slot altogether? The smallest card I could find was an 8Gb Class 10 card and it only works sometimes. If Spektrum is going to force the use of an old tech, then provide the card. This is kind of weird. With the inclusion of WiFi for updates and a USB Connection to have your TX show up as a drive on the PC, why have a card slot at all, specially one you can't get a card for?

What's the name of the cable you need to connect Crossfire TX to this radios serial port?

@StevesRC

3 жыл бұрын

SPMA3090 Crossfire Adapter Cable with Mounting Screws: iX/NX

@douglasshackett8747

3 жыл бұрын

Hey Sandman! Have you tried your nx radio with crsf yet? I'm finding it impossible to get info on nano diversity tbs.

Hi Mr! Can you teach me step by step to set up reversed at NX10?

@StevesRC

2 жыл бұрын

What do you mean? What do you want to reverse?

Thank you Steve. Please show the voice comparison between DX9 and NX10. Can it perform custom voice? Is there a tool available which we can use an app to do the configuration and upload to the NX10. The thumb knob is easy to break. (I replaced a few times already on my DX9). Thanks

@StevesRC

3 жыл бұрын

I will when I have a close to production version. I'm afraid this version has been through the wringer and the speaker is not final. Early sample life... /shrug...

Hi I try to update firmware with USB cable and got at file to put in rut directory. I forgot to change the file name from SPMTX to SPMTX.SAX, and now i cant turn the radio on. What to do? please help. Best regards Keld

I was going to replace my dx9. But i see is eventually going to be discontinued. My question is . How do i transfer my 10 plane memory to the nx10?

@StevesRC

3 жыл бұрын

Best way would be to export them to the SD on your DX9 and then bring them over to your NX with an import.

@kendonnelly3248

3 жыл бұрын

@@StevesRC Kind of a vague answer. So i have to put sd card in pc. Then hunt down where the card is located on my PC on the NX? I suggest a video. Also would there be any issues from the fact that it came from a 9ch to a 10 ch?

Hey Steve,Do you know what the class and GB micro sd card requirements are?

@StevesRC

3 жыл бұрын

Sorry for the delay. We recommend Class 6 or lower. 32gb or smaller. FAT or FAT32. Some class 10s will work from Sandisk and Toshiba.

@BinderDundat

3 жыл бұрын

@@StevesRC Thanks, now I just have wait for transmitters to get into the stores.

@DJBBBOSS

3 жыл бұрын

@@StevesRC Here in the UK the standard is Class 10 ....... ul struggle to get class 6 or less now in 2021 ........ this could render the card slot useless within a short time frame

do the nx radios have vibrate motor like the dx9? also is the speaker better? dx8 had crappy speaker, dx9 is much louder and sounds better.

@StevesRC

3 жыл бұрын

Yes they have a vibrate like the DX.

How do you connect to the wifi I have put. My password in but do not see where you go from there

@peterdickinson7638

3 жыл бұрын

i am having the same problem, could i pleaase ask for a reply many thanks

Where can I buy a 32 Gb class 6 Micro SD card - most are class 10

@DJBBBOSS

3 жыл бұрын

I know Frank.... Here in the UK class 10 is the standard now...

When will a NX14 come out. Im a Futaba guy and want more than ten channels. But I do not want android and the super slow IX12.

@StevesRC

3 жыл бұрын

While I can't say exactly what is coming out. I would say, Horizon/Spektrum understand this need in the market and is working on solutions.

Do a video on NX 10 and Aura 5 lite

@StevesRC

4 ай бұрын

Unfortunately I do not own an Aura 5 lite. Thanks for the idea though!

Is it worth getting the nx8 over the nx6?

@TangoOne

3 жыл бұрын

I was in the same boat and just ordered the NX8. The NX8 is only $40 more and also includes a $18 neck strap. The NX8 also has more software capabilities as well. I didn't want to spend $300+ on a transmitter and later down the road wish I would have just spent the extra $40.

@cG-es8mb

3 жыл бұрын

@@TangoOne I decided to go with nx6. It will be all I need I believe. Thank ya.

I want the 10. When’s that bad boy coming out?

@StevesRC

3 жыл бұрын

Very soon. Should be sometime this month.

Is it time to retire my dx6i for a NX ?

@StevesRC

Жыл бұрын

Especially now that the NX20 just came out? YES!

Ill stick with my dx9black

@OutbackKanga

3 жыл бұрын

Bought a new dx9 black today same price as the nx 10 ... choose the dx9 over the flimsy nx also there is no way transmission distance wont suffer dropping down to only using a single 3.7v cell...makes it and easy choice to buy the older 9x9.

Sense going from the DX series to the TX series the battery drop from a two cell to a single cell did the transmitting power drop as well

@StevesRC

3 жыл бұрын

Nope. Still fcc compliant and power isn’t reduced.

The reason for the new antenna location is not reasonable. It is much more likely people hold the radio up instead of down. I guess it has more to do with the more easy assembly of the antenna which saves money.

Can I use a AR630 smart receiver with the NX10 transmitter.

@StevesRC

3 жыл бұрын

Yes you can

IMPORTANT NOTE: Regarding the question of the NX transmitters working with DSM2 receivers, be very aware that the transmitter being sold in Europe are NOT, and will NOT BE, compatible with DSM2, only with DSMX. It is a regulation issue that most probably is never going to change.

@StevesRC

2 жыл бұрын

Yep

I think the price is outrages man! Ive been waiting on getting a new TX since my DX6e broke a month ago and I see finally today the NX6 is available and they dont even include the magnetic charge plug or a descent battery. This thing better live up to be a good one but they could have just made it a 7 channel..NX7 but no that would cost too much..which is BS!

@StevesRC

3 жыл бұрын

The 6 has a 7th channel my friend.

@aaronstrom16

3 жыл бұрын

@@StevesRC I apologize for the rant..it just makes more sense to me having the 7th channel programmable for other functions in instead of just SAFE..like on the hobby zone carbon cub being that channel 7 is for the flaps on that RX..would that channel be rates 100% -100% for flaps..Im getting the NX6 no matter what and im sure I will like it as much as the DX6e ive only been in the hobby for a year and its been just wonderful but the amount of money Ive spent at Horizon has been worth every dollar. Im not looking forward to rebinding the 20+ plane I have accumulated the last year. I just hope the NX6 will be worth the 300 bucks.

@isaiahfurrow7414

3 жыл бұрын

Battery should be good for about as much as you'd fly in a single day, or you can later upgrade to the 6000 mAh the MX10 has... that would be like an entire weekend of flying.... I am looking to get the NX8... because I see needing the 7 channels...for warbirds... and maybe one extra channel will makenit a bit future proof.... and because it is only like $40 more...

@BillKisel

3 жыл бұрын

@@isaiahfurrow7414 Yeah, for $40.00 more it seems to make sense to get the 8 even if now you think the 6 will suffice.

DSM2 is not allowed in Europe anymore with new transmitters (since 2015), so European transmitter models probably won't support it (just like previous transmitter models). 😉

@StevesRC

3 жыл бұрын

Definitely. Addressing the US market here ;)

I like the fact that there is no android operating system, I like instant on ready to go Systems, a separate Computer, Laptop. I pad connection is the way to go, I don‘t‘ Want to use my radio to check my email! And I surely want to wait for my radio to Boot Up !

@StevesRC

Күн бұрын

Definitely has its benefits for simplicity!

It's nice looking new NX generation but not so impressed with the interface and plastic quality. My last for 3 days and have to send it back for fixing the problem. Interface collapse and screen keeping flash non stop. My old TANK DX9 probably the best spektrum made radio. Hate the IX and try the NX,very disappointing.

RadioMaster TX16S Multi Protocol RC Transmitter

@BillKisel

3 жыл бұрын

So, you'd get the RadioMaster over any of the Spektrum NXs? Reason I ask is because I'm new to the hobby (right now flying the HZ Sport Cub S 2 RTF) and will need a radio for the UMX Turbo Timber that I plan to be getting and flying Spring 2021. Thanks.

@ultramediafx

3 жыл бұрын

@@BillKisel i would personally, i think its the best deal by far. Very customisable, affordable and supports channel mixing and open tx

@ultramediafx

3 жыл бұрын

Ill add that its important to research your specific requirements for your rig. I have found it has even more options at a fraction of the cost ecspecially for new entries.

Reminds me a little too much of the budget "E" series in how they look. The DX6E series was a little notorious at my airfield, so looking like I have one is a little off-putting. I guess that will change when these become the norm instead of the DX everyone has.

Forgot to mention I have the NX6

Why are spektrum transmitters so expensive. When other manufacturers have beet you to the table with tech and at a much lower price point

yadda yadda yadda pick ONE question and answer it fully. maybe an actual technical question.

@StevesRC

2 жыл бұрын

What question would you like me to answer then?

Problems with NX8. Negative comments removed. Software no good