Finally someone had found a solution for the sticks calibration. I’ve been messaging TBS back and fought till now and still can figure it out. Thank you so much dude that was very helpful 🎉just need to wait for the dot to move first😅

Your videos is the reason I’m able to continue flying 🙏🏽 thank you

@quadmods

Жыл бұрын

That is awesome!

Thanks I can’t thank you enough. You’re such a life saver!!

Thank you. I had been having calibration issues on my Tango 2 and this tip really helped fix the yaw readings at both zero throttle and full throttle.

I always suffered from tango2's gimbal trembling, and your video was really helpful. Thanks.

Great info, and thanks for posting. Last week I swapped out my V1 board for a V3 and couldn't calibrate the gimbals, like other Tango 2 owners. Took my time, worked like a charm!

Great tip! Been wrestling with this for a while and first try with your method yielded better results than previous bouts... Thanks!

Dude... thank you! My Mambo does beep but I must of still been doing it too quick! I also wasnt letting go of the stick at top and bottom mid like you were or only doing the + shape once like you were so i did all the same as you with slower on the main cal and its finally right! Legend.

also, the "+" shape movement at the end is super important

@hasqall

2 жыл бұрын

What is it cause actually am afraid to do tge calibration 😅 so whats that + shape ?

Just got my Tango 2 v3 delivered yesterday. I can get a good calibration on both sticks after many tries, but it seems to lose calibration on the right gimble after going in and out of different menus pages. Certainly don't trust it at this point. Changed the micro SD card, got it to calibrate using your low and slow method. So far so good. Still need to take props off and verify end points on my quad.

@quadmods

3 жыл бұрын

Good to hear, I heard the newer firmware takes care of so of these issues.

Thanks for the information!! I had this problem for close to a year now. After doing this one time it worked and everything it good now!! Thanks again!! Cheers from Canada 🇨🇦

@quadmods

3 жыл бұрын

Glad you got it calibrated, I’m in Ontario

@Rexinator12345

3 жыл бұрын

@@quadmods same just up north in north bay.

@quadmods

3 жыл бұрын

Hey cool, I was there a couple years ago to build the movie theatre at Canadore

My sticks simply don't do anything. Am I SOL?

Man really works fine!!! Wait the time for the dot moves first and then do stick movement in the same direction!!! Thanks!!!

@m4kwadfpv

3 жыл бұрын

Hey and remember the recent firmware update for the internal TX for T2 Pro V3 for 1 watt!!!!

@quadmods

3 жыл бұрын

1 watt will get me a long way in Toronto, bet my video dies before a failsafe

much appreciated,,,,, that was exqctly what I needed,,,, working great now!

Ou! Man! Thanks a lot! You save my device!

Thank´s for your help ! as a beginner it was very helpfull

Thanks for the video. I’m having the same issue with my brand new V3 Tango. When you turned on the Tango did you get the initial intro with the freedom TX logo and then the little white logo or immediately went to the calibration page?

Tks a lot, life saver

Hi,can I ask you a question please? Do you need to do this when you first get one? Or after you bind it to a receiver? Or do you need to do this everytime you change a model? thanks

@myusernameislongerth

2 жыл бұрын

Found that calibration was lost after upgrading to firmware 1.30. Upgrading to earlier firmwares did not cause the calibration loss. Out of the box there is no need for calibration, neither when binding to a receiver.

Thank you😀

This deserves wide sharing..... I must have lucked through this the first time through.

Very helpful video been fighting for the last day or two, now that said my sticks are not moving the same direction as they should how do I make them move the direction I need to any help appreciate it thanks

@quadmods

3 жыл бұрын

I would double check the mix settings. If you don’t have movement from other axis on the stick display I would guess the mixer is set wrong. Sorry I’ve not had this issue so I can’t tell you exactly.

@tonymejia2345

3 жыл бұрын

@@quadmods fix the problem got a replacement controller had software issues just got a new replacement so far so good appreciate the help and the reply

Thank you so much ... 1.2.3 Move YES ....Thank you💯💥👍

before calibration had 5 points drift now is dead canter no drift thx a lot

Tried to calibrate my new Tango 2 at today. Sort of did that except slight skewing (+- 2 to 5 units) for both stick horizontal axis at top and bottom position. Stable zero at middle though. Are there is a way how to get rid of this skewing? Or that is necessary evil?

@quadmods

2 жыл бұрын

It should not skew, keep trying to calibrate or you may have a problem with it.

Thank you thank you thank you!!!!

@quadmods

Жыл бұрын

Happy to help!

i found good results in doing the + at the end 4 or 5 times nice an slow untill it looks nice and smooth on the screen

Thank you very much I was getting crazy 👏🏻👏🏻👏🏻👏🏻

after like 5 hours jajaja thank you, so helpfull

@quadmods

Жыл бұрын

Glad it helped!

Thank you so much! helped a lot. solved the problem

How can I reset my calibration sticks from what their already set too now? I can’t see an option to this

@davidcanole3758

3 жыл бұрын

Recal.

Hey there thanks for the video! I’m having trouble Arming my iflight Cidora. My TBS nano RX is binded with a solid green light and I already created a model and got a to arm once before and now I’m having trouble figuring out what the problem is. The only thing I can think of is maybe some thing got changed when I tried to use a simulator on the same model. Just reaching out for help. Any ideas?

@quadmods

3 жыл бұрын

Would you happen to be in another model? The RX stays with the model when you switch.

Thank you good man

u save my life....thank uuuuu

thanks for this video! this helped so much

Life saver! Thank you. Subbed

@quadmods

2 жыл бұрын

I’m glad it helped 👍

Thanks you bro, you 👌

@quadmods

Жыл бұрын

No problem 👍

that was helpful. thank you.

Vielen Dank🥳

i need help...do you know how to scale the sticktravel ? i reach -100/+100 at about 1mm from center. have you any idea how i can fix this?

@MrSmithFPV

3 жыл бұрын

Yes, because you dont done it like in this video. Do it the right way and all is fine.

@smokinjoe1256

3 жыл бұрын

@@MrSmithFPV your video is shit. i did everything right.....broken sensor.

@MrSmithFPV

3 жыл бұрын

@@smokinjoe1256 it's not my video and your sensor is not broken... 😉

good idea to run the remote control without antennas

I still have throttle warning when i boot up the tango2

finallyyyyy thanksss

They recommend both sticks at same time

Man I was struggling with this all day today. I couldn’t figure out what was up with the calibration. I musta did it 30 times. I’ll have to use the info you’ve Given here and re try tomorrow. Ty