This is very poor job of re-sleeving a cylinder head, the actual process is very different bcz it involves heating the cylinder and shrinking the sleeve with cold it takes a precise amount of calculation and almost ration of heat and cold for re sleeving cylinder and perform effectively.
@ramshadr6927
2 жыл бұрын
Absolutely
@vnsworkshop9961
2 жыл бұрын
Nooooooo You must warm the cilynder and male the sleeve col. Than it will go inside with free play to align. In just 5 second than you align the port.. Why this people don t sue the head...
@outdoorbikingbrothers52233 жыл бұрын
Where is this shop?
@tscooter81032 жыл бұрын
OMG No! No! that sleeve is so loose it will not be able to dissipate its heat to the cylinder for cooling, and the worst is that sleeve will "Walk" and push out the head gasket. please nobody do this its a hack butcher job. great installation information can be had from either LA Sleeve or my boys at Advanced sleeve around the corner.
@darklence87844 жыл бұрын
എന്ത് തേങ്ങാ ആണ് ചെയ്യുന്നേ ഇങ്ങനെ ആണോ sleeve ചെയ്യുന്നേ. അപ്പോൾ കുറെ കാലം കിടക്കും.
@Srivishnutejas2 жыл бұрын
Thank you 💛
@szymoozz3 жыл бұрын
Ahh the good old swing press
@javithu63 жыл бұрын
சூப்பர் bro
@rahulgumber37184 жыл бұрын
Nice work
@vickysvlog38304 жыл бұрын
Evolavu Aachi bro How much cost bro
@cselvaraj31283 жыл бұрын
Bro Yamaha RX100 bike la sleved and unsleved yaepadi kandu pudikaradhu konjam busy. Very urgent.
@srisundar7890
2 жыл бұрын
Bore ulla porting pannirukanu pakanum bro
@desmondlloyd75683 жыл бұрын
Wrong method.fitment also loose
@rashmiranjansahoo78222 жыл бұрын
Once sleev is last over size what's next Can i use that block or not
@gaurakshak_saurav
Жыл бұрын
not
@muthumuthu34263 жыл бұрын
Super
@neerajmalhotra95854 жыл бұрын
Bhaiya apna shop ka address batao
@vintage.vibees2 жыл бұрын
Suzuki shaolin cyinder port pannuma ?
@srisundar7890
2 жыл бұрын
No sir sleeve not available ...
@Creatives-World4 жыл бұрын
Sleeve installation kay baad kesi performance hoti hy RX115 ys 135 ki. Kuch loog kehtay hein 2stroke mein sleeve successful nahi rehti pick aur power mein faraq aajata hy. Aur piston bhi seize hota hy
@rishigovekar1419
3 жыл бұрын
Port matching ho toh kuch problem nahi hoti hai
@urvish6649
2 жыл бұрын
@@rishigovekar1419 right
@boymarbs8860
5 ай бұрын
@@rishigovekar1419yes a 💯 right
@manojkumardme45269 ай бұрын
Price
@ashishpatpingua40154 жыл бұрын
Ekdum badiya bro 👌👌👍
@akibkumbari37904 жыл бұрын
Tell us what's standard size and sleeve size
@Deepakgs-bu6mx
4 жыл бұрын
0.25 mm bro
@akibkumbari3790
4 жыл бұрын
@@Deepakgs-bu6mx if in micrometre it says 50.23mm then till what size ull do honing
@Deepakgs-bu6mx
4 жыл бұрын
@@akibkumbari3790 the next size will be 0.75
@akibkumbari3790
4 жыл бұрын
@@Deepakgs-bu6mx bhai agar 50 mm ka block size hai n oversize piston 0.25mm ka hai to aap isko kitta boring n honing karoge
@Deepakgs-bu6mx
4 жыл бұрын
@@akibkumbari3790 bhai standard size hai 0.25 agar honing karoge toh next piston size apko market mai 0.50 hoga
@mananchaudhary13264 жыл бұрын
Bro can you tell me what is the procedure of removing an old sleeve
@danieldzvonik9164
3 жыл бұрын
heat it up in a oven and carefully tap it out with a block of wood
@sahilpatil7418 Жыл бұрын
How much it does cost
@surajliferocks
Жыл бұрын
Sleev cost 1500
@boymarbs8860
5 ай бұрын
@@surajliferocks I want to put new sleeve on my 5speed block It will be alright?
@rsjeyaram30302 жыл бұрын
bro ethu avlo price bro sollunga en bike ku change pannanum
@srisundar7890
2 жыл бұрын
3800
@Abhi_kahar_16273 жыл бұрын
Successful hota hai kya ye sleeve rx135 mei
@vikasmishra8150
2 жыл бұрын
Ha bhai sahi tarike se hoga to acha kam karta hai...original jaisa to nahi lekin dum hota hai
Пікірлер: 63
This is very poor job of re-sleeving a cylinder head, the actual process is very different bcz it involves heating the cylinder and shrinking the sleeve with cold it takes a precise amount of calculation and almost ration of heat and cold for re sleeving cylinder and perform effectively.
@ramshadr6927
2 жыл бұрын
Absolutely
@vnsworkshop9961
2 жыл бұрын
Nooooooo You must warm the cilynder and male the sleeve col. Than it will go inside with free play to align. In just 5 second than you align the port.. Why this people don t sue the head...
Where is this shop?
OMG No! No! that sleeve is so loose it will not be able to dissipate its heat to the cylinder for cooling, and the worst is that sleeve will "Walk" and push out the head gasket. please nobody do this its a hack butcher job. great installation information can be had from either LA Sleeve or my boys at Advanced sleeve around the corner.
എന്ത് തേങ്ങാ ആണ് ചെയ്യുന്നേ ഇങ്ങനെ ആണോ sleeve ചെയ്യുന്നേ. അപ്പോൾ കുറെ കാലം കിടക്കും.
Thank you 💛
Ahh the good old swing press
சூப்பர் bro
Nice work
Evolavu Aachi bro How much cost bro
Bro Yamaha RX100 bike la sleved and unsleved yaepadi kandu pudikaradhu konjam busy. Very urgent.
@srisundar7890
2 жыл бұрын
Bore ulla porting pannirukanu pakanum bro
Wrong method.fitment also loose
Once sleev is last over size what's next Can i use that block or not
@gaurakshak_saurav
Жыл бұрын
not
Super
Bhaiya apna shop ka address batao
Suzuki shaolin cyinder port pannuma ?
@srisundar7890
2 жыл бұрын
No sir sleeve not available ...
Sleeve installation kay baad kesi performance hoti hy RX115 ys 135 ki. Kuch loog kehtay hein 2stroke mein sleeve successful nahi rehti pick aur power mein faraq aajata hy. Aur piston bhi seize hota hy
@rishigovekar1419
3 жыл бұрын
Port matching ho toh kuch problem nahi hoti hai
@urvish6649
2 жыл бұрын
@@rishigovekar1419 right
@boymarbs8860
5 ай бұрын
@@rishigovekar1419yes a 💯 right
Price
Ekdum badiya bro 👌👌👍
Tell us what's standard size and sleeve size
@Deepakgs-bu6mx
4 жыл бұрын
0.25 mm bro
@akibkumbari3790
4 жыл бұрын
@@Deepakgs-bu6mx if in micrometre it says 50.23mm then till what size ull do honing
@Deepakgs-bu6mx
4 жыл бұрын
@@akibkumbari3790 the next size will be 0.75
@akibkumbari3790
4 жыл бұрын
@@Deepakgs-bu6mx bhai agar 50 mm ka block size hai n oversize piston 0.25mm ka hai to aap isko kitta boring n honing karoge
@Deepakgs-bu6mx
4 жыл бұрын
@@akibkumbari3790 bhai standard size hai 0.25 agar honing karoge toh next piston size apko market mai 0.50 hoga
Bro can you tell me what is the procedure of removing an old sleeve
@danieldzvonik9164
3 жыл бұрын
heat it up in a oven and carefully tap it out with a block of wood
How much it does cost
@surajliferocks
Жыл бұрын
Sleev cost 1500
@boymarbs8860
5 ай бұрын
@@surajliferocks I want to put new sleeve on my 5speed block It will be alright?
bro ethu avlo price bro sollunga en bike ku change pannanum
@srisundar7890
2 жыл бұрын
3800
Successful hota hai kya ye sleeve rx135 mei
@vikasmishra8150
2 жыл бұрын
Ha bhai sahi tarike se hoga to acha kam karta hai...original jaisa to nahi lekin dum hota hai
Yamaha new bike 2002 chahiye kallu
Full video post pannu ga bro
100 Persent saaf kam
Poor Sleev Work Pasting With Araldite
No perfection 😂😂
Number bron
Ggg
number
Not a proper work.. Old process this is
It's not successful
🚮 Total waste job cleanly recorded on cam 🤣
Tumhara number bhai