This was so helpful and the best video by a longshot. Thank you. Waiting patiently (impatiently, really) for part 2...... hope it comes soon so i can replace gear worm in my daughters singer 518.

I have just used this video to replace the bottom hook drive on a Singer 507 and it is now working fine. Thank you.

@ClintWaffle

7 жыл бұрын

Mike Bracey what size driver is it?

This is just the video I needed. Thank you!!

Huge thanks to this video. I've successfully replaced the gears. However, now I'm facing a problem... The setting of the switch for popping the bobbin is off... No matter how I switch it, the bobbin would not get filled... It will be really nice to have another video showing how to put the gears back and how to set up the switch, the timing and so on.

I wish we had part two on the assembling,adjusting and timing. This was a great video and I'm sure I'll get figured out through other videos on adjustments

I hope part 2 is coming along soon- I have a machine on my floor that needs this!

Great video! Wife and I simply reversed the teardown steps to reassemble. The bobbin turned out to be the hardest to put back together. But we just kept watching until we got it all back. Sews great now!

@donnapeck1968

4 жыл бұрын

david mcgaughey we are having a terrible time putting it back together. Any hints and on the timing?

Please post video #2. Getting it back together is almost always the harder part.

My timing is off on my 756 touch and sew...is there a video on that? I think I'm looking at the right gear...to the far left under the bobbin case?

It’s been 4 years, Where is video #2?

I have a750. I followed all the dismantling shown in the vid and then reversed the process to exchange gears but my hook moves and does not keep in adjustment. It is not solidly attached it seems. What did I forget?

how about replacing the timing belt? For example how does it come off the top side?

What size hex tool do you use to loosen the set screw on the bobbin winder cam.? My set screw is smaller than 1/16. Where do you get the tool you use?

It was very useful, hope part 2 will coming sooner. I have singer 617U, iam facing miss timing problem and also missing some set screw also forged to put back after remove, can you help me Sir🙏🙏🙏

Cannot get bobbin winder set screw off. Using allen wrench. What size screw drivers are you using? I noticed each set screw is a different size. Put PB Buster on the winder set screw.

HI.. I. recently bought a used industrial sewing machine 281-1. Do you have video how to change belt on this machine? Thank you

Hi, Please show the complete video of how to disassemble singer 1408 promise sweing machine, complete discription of parts and repairing

nice👍

Dear Sir, Would this be involved with the Flexi Stitch not performing correctly in a 758? The top end FEED follower is seemingly fine when I watch it side by side with a working twin machine. That behaves right, but for whatever reason the patterns double back on themselves or compress, not enough Reverse and too much Forward. There is a 'clunk' on the lower bobbin side as she runs the Flexi Cam, Sound familiar? If this is what is going on I can do the job but thought I'd ask before getting into it as the machine is otherwise in mint condition and runs a perfect Zig Zag, just not much the Flexi patterns. Thanks, Alexander in Gloucester Ma.

@SINGERonlinecom

6 жыл бұрын

The flexi patterns have a balance adjustment on the top of the machine next to the cam opening. Its a forward/ backward adjustment.

I have 603e is not working motor is screaming what should I do

Great video. I've replaced all 4 gears. The machine is sewing fine, the only problem after reassembling is that it will not wind the bobbin. Could there be something I've overlooked ?

@johnlukasavitz4897

4 жыл бұрын

The hole that the drive pin fits into on the bottom of the gear may not be drilled deep enough to allow the long pin that drives the bobbin to move up enough to engage the bobbin and drive it. Drill the hole in the gear deeper until the drive pin moves up and there is full engagement of the long drive pin in the bobbin.

Do you need to set all the set screws loose?...my vertical gear broke in half and I tried to set the nut loose to get down to the issue that my bobbin overall was having...but I believe I broke a metal part that connects to the bobbin winder driver. I want to order the parts but want clarification of what I would need to fix it. Question on the left handed thread lifting nut...do you loosen it by turning it to the right...versus the left...(lefty loosy righty tighty is not applied here???) If so, then maybe thats why i broke mine...help!

@SINGERonlinecom

8 жыл бұрын

+Karen Nieto Sorry for the delay, please give us a call if you still need help 800-559-6729 SINGEROnline.com ... The nut is a left handed thread so righty loosy in this case.

Can you help me troubleshoot. I have watched every video i can find. But the 2nd thing you took off the gear under the bobbin i can turn it with my finger but the bobbin house is not turning at all. Any idea what would cause that and what i need to do to fix it.

H0w d0 fix a single touch n sew special zig zag model 638 when needle wont pick up bobbin thread or winding it

@SINGERonlinecom

6 жыл бұрын

Machine is out of time. Get in touch if you are interesting in purchasing a manual that helps with this issue.

How do I release a roll pin in the top vertical gear in a singer model 648? I'm having problems finding a way to remove it in such tight space. Any suggestions? A set screw would have been easier....

@SINGERonlinecom

6 жыл бұрын

You have to make a nail punch and grind it down to fit that pin hole. Punch it from front to back with a light hammer and then pull it out the back with a pair of vice grips. Remove the shaft and grind a flat spot on it to accommodate the new gear and set screw. Hope this helps!

This is very similar to the singer 467. Not easy to find a video on how to replace the most common gear that fails....the top gear.

For the bobbin winder set cam...the first piece to remove...I can't remove with my standard size allen keys. Is there a special size I need?

@lisalu910

2 жыл бұрын

Exactly. I also couldn't even get past Step 1 and I have the hex keys in both sizes (MM and SAE) yet I still couldn't budge that screw. Nor could I budge the nut at the bottom of the hook gear. So basically, unless someone takes the time to show HOW to do that, I'm stuck!

@aprilmccrum7667

2 жыл бұрын

@@lisalu910 Yeah I gave up, but still want to be able to fix without having to pay for someone to repair it. I might try again but got so frustrated.

@aprilmccrum7667

2 жыл бұрын

Yes I can totally relate. Very frustrating 😕

Thank you for this video! My feed dog gear crumbled and I have new gears to install. Help find part 2 please!!

Por favor mi maquna es 758 no prende el pedal esta bien que le puede estar sucediendo la verdad el motor no indican como se podría probar si esta recibiendo corriente o como bajarlo pues mecánicos por estos días difícil podrían trasmitir por favor en español

So I was working on cleaning, inspecting and oiling a Singer T&S II Model 771 that I got and am rehabbing. Upon accessing the bottom feed and bobbin drive area, I found two halves of a thin washer. I can't for the life of me figure out where it previously existed. I don't see it in these videos and haven't found references in online repair manuals and can't seem to find an exploded parts list anywhere. Do you have any suggestions? I am assuming it served some purpose at some point.

@binkle52

5 жыл бұрын

it seems to have a half inch internal diameter, and ~3/4 inch external diameter & 1/16 inch thickness

@shellyh6320

5 жыл бұрын

@@binkle52 Hi binkle. Pretty sure you are describing the retaining clips - there is one for the end of each shaft and you should be able to see a small groove for them to clip into. I'm not a pro or anything, just happened to have just watched another video that showed them. cheers

what size screw driver is the driver that removes the screw in the lifting plunger?

@SINGERonlinecom

6 жыл бұрын

I think you are referring to the bobbin winder lifting cam. The screw is a 1/16" allan screw.

What kind of tool did you use to remove the gears?

@SINGERonlinecom

8 жыл бұрын

+Alex Haupt I used 3/32" allen wrench

Por qué no hacen sus instrucciones en español

where is the part 2 on how to reassemble it?

Hey, I'm currently trying to follow this video to replace my feed gear. Is there a very specific Allen Key I am supposed to use that's specific to singer machines? I've got a singer 1411

@naomi429

7 жыл бұрын

I'm having a bit of a goldie locks moment with the keys that I do have.

@SINGERonlinecom

6 жыл бұрын

It might be a metric 3mm allen wrench.

Mi Singer touch sew-ll modelo 778 pega el aguja enla parte de abajo ayudenmeee porfavor

Your videos has really been of help please how do I get singer gears model 513 singer. Am in Nigeria Lagos

@sergelongtin785

6 жыл бұрын

Try Amazon? I get mine there.

I can not locate the video that was mentioned as "part 2" assebling and timing with the new gears...Could you post a link or thread.... Thanks; Allan

@SINGERonlinecom

6 жыл бұрын

kzread.info/dash/bejne/qmaVxaiDlafep8o.html

On the video itself...setting the machine to felxi will allow the removal the entire hook drive shaft...I always run into issues with buttonholers unit stuff...that I am going to have to check out on my own 750's...funny 30 years of fixing them and I've always pulled the motor and tweak rods to get that shaft out far enough....perhaps I've learn something that even the service centers didn't share with us repairman then...thanks...Terry - www.tandtrepair.com

I cannot remove the feed gear long shaft At 4 minutes mark, "Set machine on stretch stitch". While this does move some of the metal arms up, they are still too low to slide out the shaft. So what is the secret?

@louisemey

6 жыл бұрын

That's where we are at also ... Did you get an answer?

@SINGERonlinecom

6 жыл бұрын

You have to cut off the finger and grind down the other piece.

My Singer 7463 sewing machine suddenly the needle doesn't pick up bobbin threat how I fix it?

@ClintWaffle

7 жыл бұрын

Sornsuda Lien just like this

@SINGERonlinecom

6 жыл бұрын

This video may help: kzread.info/dash/bejne/X6l6w8t_pbaZfdo.html

Hello, I am trying to replace the dog feed gears on a Singer 1036 sewing machine...I watched the video (very good) when I got to the part on my machine to take out the shaft...It is stuck...did not want to force it too much. I used a towel to cover the shaft so I would not scratch it.. I keep hearing a clicking sound , all of the parts are loose >>>>Please Help!

@SINGERonlinecom

8 жыл бұрын

+Tipp Harris OK a little late responding, however the 1036 machine has a c-clip on the long horizontal shaft (you have to take it off) then slide the shaft out to the right. Put your new gear on, slide shaft all the way back in, the left side has a flat spot for the horz. hook gear set screw to tighten to. The clicking sound is the shaft sticking on the c-clip.

@jhoncampos9313

5 жыл бұрын

Quiero en español es costa rica

where is part two?

mantenimiento toch 2001

Any part 2 yet?

@SINGERonlinecom

6 жыл бұрын

kzread.info/dash/bejne/qmaVxaiDlafep8o.html

@purplegamba

4 жыл бұрын

@@SINGERonlinecom This part 2 video is just part 2 of gear removal. Do you have a video showing installation of the new gears?

Well this would be helpful IF you actually showed how to loosen or remove the various set screws. I guess you had already gone in and loosened them up for the video, and didn't stop a second and explain how to get those off. If I can't remove them, the whole project is impossible. Also if you slowed down and made sure it was in focus as you removed those set screws, that would help.

@aprilmccrum7667

2 жыл бұрын

Agreed 100%

Stuck at "Set machine on stretch stitch" ... how do you set the machine to stretch stitch enough to move the bar out of the way.

@SINGERonlinecom

6 жыл бұрын

Charlotte, you have to cut the bar off when the machine is in stretch stitch mode.

Only comment to add is that the nipple you speak of on the large feed gear...that is just there...there are actually lines scribed in the eccentric and feed carrier. When those align the feed timing is proper...but, 1st you have to ensure the needle to hook timing is in place and set, then you set the feed timing with those two marks. Hope it helps some - Terry www.tandtrepair.com

@terryfielding9386

9 жыл бұрын

Terry Fielding Meant to say too...the eccentric and eccentric feed carrier...there are lines scribed in those...and those line up when the needle to hook timing marks are in position.

@rachaelekeroth2046

8 жыл бұрын

+Terry Fielding Thanks. How do I go about ensuring the needle to hook timing is in place and set? Do you know of a video for doing this? I think that is all I need for my machine. Thank you.

"1,000"

"1,236"

This video is terrible. First of all, how are we supposed to follow along with all the things that you have loosened if you did it ahead of time. Secondly, you never posted an instillation video as promised... so great. I've now taken a part my machine and have to watch this video in reverse to try to figure out how to put it bak together and SURPRISE: my machine doesn't work anymore. THANKS SINGER.

Joke's on everyone here. They're never going to post the second video, because now your machine is inoperable, so you're more inclined to buy a new one!

Terrible video. He skips over the most important part. Setting machine to stretch stitch does NOT move all the linkage out of the way. Thank goodness there is another video out there from singer online that tell you to bend over a bracket and to cut off a little piece of the machine that is not needed to get that longer saft out. Don't even watch this one