Thanks for showing how to use it! Great job designing it in house!
@mariorodriguez67923 жыл бұрын
Just put mine on my srt8 300!!! Looks fucking awesome
@alexanderbustamante72374 жыл бұрын
can i buy the screws, rivnuts, bolts and washers at a homedepot or lowes ?
@DMVTONE4 жыл бұрын
Will 3/8 bit work for drilling the holes?
@genevox29413 жыл бұрын
worst possible angle but itll do Sir😎installing mine today
@PurpBoss224 жыл бұрын
A lot of the other videos I seen said is a 3/8 drill bit
@PureSportsDesigns
4 жыл бұрын
Ours is 25/64" as per spec on all of our Rivnuts
@kylerebman50943 жыл бұрын
What if the nut where the wrench holds onto keeps wanting to spin on me?
@enriquearellano3267
2 жыл бұрын
Did you figure it out ? Same thing just happened to me
@kylerebman5094
2 жыл бұрын
@@enriquearellano3267 so I learned that the rivnuts I had were stainless steel, a stronger material that you can't manually install with this method. The rivnut used in this video was aluminum, weaker material. I needed a rivnut tool for my case.
@ronniewalker60332 жыл бұрын
Where do I buy yours frm
@PureSportsDesigns
2 жыл бұрын
www.eBay.com/str/PureSportsDesigns
@LuxLazar5 жыл бұрын
Any recommended torque specs?
@PureSportsDesigns
4 жыл бұрын
The rivnut is aluminum and the bolt is steel. It doesn't need much torque to compress the rivnut. You can definitely feel when it has bottomed out and stops compressing.
@hernandezruby13 жыл бұрын
If it’s loose what can I do to fix problem
@CRWM3N1
3 жыл бұрын
The riv nut?
@Misterdre2you
3 жыл бұрын
Mine just came in today. I'm waiting for my tips to come in hopefully tomorrow and I will be putting everything in one day. Paint my calipers, change the rear valance and tips and add the wicker. I see on the video that each rivnut should have washers and a star washer as well, my pack don't have any of those so I'll have to get some. But to make sure they don't loosen up, I'm going to add a little lock tight to mine to make sure they don't back out. Nice to see such a beautiful woman into your car Ms Hernandez
@hernandezruby1
3 жыл бұрын
@@Misterdre2you hope you enjoy it as much as I do it makes my charger look aggressive 😂 I have 5 inch tips what you getting also very nice magnum 🔥🔥
@Misterdre2you
3 жыл бұрын
@@hernandezruby1 thank you Ms Hernandez, currently Kandy (my Magnum is out of commission waiting for me to get her a new motor. Now I'm driving my 300s. That's where I'm putting the wicker bill. I just thought of something I wanted to do before I install it along with the SRT valance and 5" tips. I have everything need to put it all on except the paint that I just ordered tonight to add a little touch to the wicker. Maybe by next weekend I'll have it all done. I also want to paint my calipers so it will be a full weekend. Hit me up on Instagram at mrdre_300s
@Misterdre2you
3 жыл бұрын
@@hernandezruby1 I did a dry fit of the wicker last night when I got home from work and wasn't to happy, it's not as big as I thought it would be. It's only like an inch above the Spoiler 😔. I'll take picture when I do it again, maybe when I get home I might try it again. Do you have pictures of yours?
Пікірлер: 21
Thanks for showing how to use it! Great job designing it in house!
Just put mine on my srt8 300!!! Looks fucking awesome
can i buy the screws, rivnuts, bolts and washers at a homedepot or lowes ?
Will 3/8 bit work for drilling the holes?
worst possible angle but itll do Sir😎installing mine today
A lot of the other videos I seen said is a 3/8 drill bit
@PureSportsDesigns
4 жыл бұрын
Ours is 25/64" as per spec on all of our Rivnuts
What if the nut where the wrench holds onto keeps wanting to spin on me?
@enriquearellano3267
2 жыл бұрын
Did you figure it out ? Same thing just happened to me
@kylerebman5094
2 жыл бұрын
@@enriquearellano3267 so I learned that the rivnuts I had were stainless steel, a stronger material that you can't manually install with this method. The rivnut used in this video was aluminum, weaker material. I needed a rivnut tool for my case.
Where do I buy yours frm
@PureSportsDesigns
2 жыл бұрын
www.eBay.com/str/PureSportsDesigns
Any recommended torque specs?
@PureSportsDesigns
4 жыл бұрын
The rivnut is aluminum and the bolt is steel. It doesn't need much torque to compress the rivnut. You can definitely feel when it has bottomed out and stops compressing.
If it’s loose what can I do to fix problem
@CRWM3N1
3 жыл бұрын
The riv nut?
@Misterdre2you
3 жыл бұрын
Mine just came in today. I'm waiting for my tips to come in hopefully tomorrow and I will be putting everything in one day. Paint my calipers, change the rear valance and tips and add the wicker. I see on the video that each rivnut should have washers and a star washer as well, my pack don't have any of those so I'll have to get some. But to make sure they don't loosen up, I'm going to add a little lock tight to mine to make sure they don't back out. Nice to see such a beautiful woman into your car Ms Hernandez
@hernandezruby1
3 жыл бұрын
@@Misterdre2you hope you enjoy it as much as I do it makes my charger look aggressive 😂 I have 5 inch tips what you getting also very nice magnum 🔥🔥
@Misterdre2you
3 жыл бұрын
@@hernandezruby1 thank you Ms Hernandez, currently Kandy (my Magnum is out of commission waiting for me to get her a new motor. Now I'm driving my 300s. That's where I'm putting the wicker bill. I just thought of something I wanted to do before I install it along with the SRT valance and 5" tips. I have everything need to put it all on except the paint that I just ordered tonight to add a little touch to the wicker. Maybe by next weekend I'll have it all done. I also want to paint my calipers so it will be a full weekend. Hit me up on Instagram at mrdre_300s
@Misterdre2you
3 жыл бұрын
@@hernandezruby1 I did a dry fit of the wicker last night when I got home from work and wasn't to happy, it's not as big as I thought it would be. It's only like an inch above the Spoiler 😔. I'll take picture when I do it again, maybe when I get home I might try it again. Do you have pictures of yours?