Smooth

I set the clips in as I'm running out the gutter, saves some time.

@TheBearGrylz

4 жыл бұрын

Natalie P me too.

@gregcarpenter4360

2 жыл бұрын

Then your slow then

Made it look easy guys

Ten years later !!

Good work... coming from a gutter installer! 🤙🏻

@nicholaspacheco4554

3 жыл бұрын

Nah not really

@gutterguy1

3 жыл бұрын

@@nicholaspacheco4554 lol

@bigdaddybaldwinb1048

11 ай бұрын

Right like why not drop the hangers as the run is being rolled out ??

Good job on the installation.

..put some grease on that axel

How far apart in terms of inches or feet do you drill every screw across the gutter when hanging it up on the house ?

@sweeneymotorsports82

Жыл бұрын

Depending on the house and the construction of the trim we go 16” on the rafter tails,

@prodgottii

Жыл бұрын

Every 2 feet for 5 inch every foot for 6 inch

Need some oil on your machine bro!

Set the hangers as your running out. Seal the end cap as your running. The helper should be on back side, not front where he can mare the face. No tri pod needed. Good work though. Why fuck with downs while running and hanging gutter? Do that shit after. Did You pre measure that downspout before that piece hung? Get some quick screw hangers and you don’t gotta pull screws from your pouch.

@TheBearGrylz

4 жыл бұрын

Appreciate your work but there’s faster ways. Try a hack saw instead of a dragging a miter saw around for downspouts. Cut the piece on sight between your legs w a hack saw. Much faster, same quality cut.

@israelmagallanes1623

3 жыл бұрын

Hangers mess with pitch, end cod can wait.. there’s stands for a reason helper should be pullin metal... and you can always slap on a down while you’re hanging a piece if convenient. And if you pre measure an out let it almost never comes out straight... wrong.. and buying hangers with built in screws just so you don’t grab them out of your pouch is just lazy. Also... hack saws leave a disgusting finish as well... your entire comment is invalid.

Pop the hole when the gutter is up it's real easy to use ur return to line up where it's going fuck measuring for holes waste of time in my opinion

Best equipment? Maybe you should lube it so we don't have to hear it. Lmao this video is pissing off the neighbors dog!!

Rookies .

@nicholaspacheco4554

3 жыл бұрын

No kidding

@vaitozloko...4491

Жыл бұрын

Hahaha. Yes sir

wrong within the first 10 sec. forgot a very important step after placing the end cap

@thejimmy6533

4 жыл бұрын

That being?

@resultspaid7250

4 жыл бұрын

@@thejimmy6533 Crickets. I guess it's a secret.

@TheBearGrylz

4 жыл бұрын

Forgot to seal the end cap

@ThePete1891

4 жыл бұрын

@@TheBearGrylz mabey he does so after it is hung, so he don't get his hand in it, and the get caulk prints on his clean white gutter?

@darryltaylor9916

4 жыл бұрын

..it's harder to fit a caulk gun in a gutter that is hung...I caulk right away or when the drop is in (if there's a drop in that end), so you only pick the caulk gun up once...unless you are doing miteres the caulk gun stays on the truck.but never after it's hung unless the piece is too long and has to be shortened....1 guy can make a gutter, the other guy could have snapped a line...they did good over all.

This was not a seamless gutter.

@darryltaylor9916

4 жыл бұрын

..did you see the machine make the gutter in 1 piece?