Je suis français et je me lance dans le même projet, tes vidéos m'aident beaucoup Merci, c'est du bon travail 👍

Nice pace, I’m not a mechanic so I like your completeness.

1000% thank you. I have to replace a cylinder head in mine. I waited a year to do it (mostly because I wasn't sure how) I got to the the top of the cylinders yesterday and wasn't sure what the next step was. I can't thank you enough for posting :)

@h2omechanic

2 жыл бұрын

I just finished the engine assembly. Videos will be posted in a day or 2. Lots of content to edit on engine builds

Found you from your post on facebook. Awesome

Awesome video man just straight info; I didn’t even need to watch but I did just cause it was good….currently rebuilding a spark after the hull was destroyed….👍👍

They make a tool to stop the crank shaft from turning to get the output shaft off.

Hey man, I've just swapped the engine in my sea doo spark with a new one, got it in and fired up however it is still showing an engine code. Idles fine on the stand with water hooked up. Any ideas?

@h2omechanic

11 ай бұрын

Dealership needs to plug in the code reader. I sold this ski & bought a 2 stroke.

Do you need a motor jack or lift or you can lift the motor by hand with a help of someone

@h2omechanic

2 жыл бұрын

2 ppl can lift it out easy. Probably 90lbs

Can you tell me do I need to change th8s m9 bolts?thank you

@h2omechanic

2 жыл бұрын

Yes, all 16 must be replaced. Re used they might break or cause a leaky head gasket

@tinokardum1600

2 жыл бұрын

@@h2omechanic Can you tell me for this m9 are they stretching bolts or normal?because i dont want to buy them if they are not stretching?ty

@h2omechanic

2 жыл бұрын

@@tinokardum1600 they are stretched yes. Replace them

If you should change the crank. Do you have to take of the TOP of the engine!? Could you just loosen the cain. And take of the chain lock at the crank?

@h2omechanic

Жыл бұрын

I believe you could remove the bottom section of the engine, but your so deep into it, why not refresh the engine entirely

@runeelli

Жыл бұрын

@@h2omechanic Thank you. But. Mine has no problems now. It only has 80hours. So just a crank change from the bottom is a "easy" job. Compare to take to. Top off. I think its strong engine. One guy I talked to has run his for 900 hour without any problems. Just regular maintenence.

Out of curiosity did you attempt to turn the crank in that condition? Wondering if those valve guides woulda kept you from it?

@h2omechanic

Жыл бұрын

No, it sat for too long, I assumed the valves could be stuck & didn't want to ruin the head if it were.

No new crank needed, the PTO on the 14/15 cranks is sweated on and can be pressed off and replaced. I have a video of this

@tinokardum1600

2 жыл бұрын

Can you send me a link?

@h2omechanic

2 жыл бұрын

My crank is still at the machine shop. I'll give out his info once it's done and done correctly, if he's OK with it. He's holding up progress...

@gustavoperez7764

2 жыл бұрын

Can you send me the link I have the same problem

@THEGAFMASTER

2 жыл бұрын

So we’re you able to press the PtO off? Or no

@h2omechanic

2 жыл бұрын

@@THEGAFMASTER yes. With Alot of heat. I have a video on the crank getting threaded

All seadoo ski are junk. Go with Yamaha.

@h2omechanic

Ай бұрын

I sold it soon as I rebuilt it and bought a All original 96 Wave blaster 2