Save 🤑 by DIY : 2016-2018 Lexus ES350 Passenger Side View Mirror Removal and Installation.

Автокөліктер мен көлік құралдары

Where to buy: www.revemoto.com/collections/...
This is the easiest way to remove that 2017 Lexus ES350 Side View Mirror saving you hundreds of dollars.
2017 Lexus ES350 Side View Mirror Replacement:
We'll walk you through how to remove a 2017 Lexus ES350 Side View Mirror Replacement and install a brand new Lexus mirror replacement.
00:00 Where to get new painted mirror
01:19 Taking off Door Handle Cover and Armrest
02:00 Remove Screws
03:58 Remove Door Panel
05:23 Taking off 4 10mm Screws
07:25 Unplug and Remove
08:39 Install New Mirror
Very simple and straightforward job. Removing a side-view mirror sounds harder than it really is. The tools you will need are the standard flat head in case you can't remove the inner cover with your hands. Of course, you cannot forget your trusty socket wrench. There are four 10mm bolts that hold the mirror in place. First, remove that inner cover it looks like a black triangle shaped piece. You will then locate 4 10mm bolts using your 10mm socket wrench remove the bolts. Once bolts are removed hold the mirror with one hand and then disconnect the wire. Pull the mirror out and sometimes with gentle force if its stuck. Repeat the above steps in reverse and be sure to check the functionality of the mirror. Thanks for watching!
Subscribe: kzread.info?su...
Follow Us on
FB: / revemoto
IG: / revemoto
Twitter: revemoto?lang=en
________________________________________________________
#lexus#es350 #diy #sideviewmirror #revemoto #paintedautobodyparts #cars #partsforcars #carparts #carmirror
DISCLAIMER: While ReveMoto tries to make the information in this video as accurate as possible, we make no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself (DIY) projects entail some risk. It is the sole responsibility of the viewer to assume this risk. ReveMoto is not responsible or liable for any loss, damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 6

  • @bobj6515
    @bobj651511 ай бұрын

    This is the greatest video ever! It saved me nearly $1000! I have sheared off outside mirrors on my 2016 Lexus NX200t on a couple of occasions. Taking it to the dealer for repair cost me around $1000 last time. This time I knew it would be even more. However, I was able to find the OEM Lexus outside mirror for $200 online. I then watched this video a few times. Removing the door panel was very easy. Unplugging the mirror wiring harness was also easy. On the NX, the controller was not in the way of reaching the 3 nuts holding the mirror assembly to the body, so there was no need to move that. The only problem with the installation came with removing those 3 nuts. I did not have a 10MM hex nut driver bit for my electric drill. I would have needed and extension for the bit as well as the nuts are about 2.5 inches deep. I did a workaround by using a manual 10mm nut driver. However the nuts themselves had been installed to be very tight and i could not twist the nut driver with enough power to loosen them. My fix was to place the nut driver on the nut and then hold the handle of the nut driver with pliers for leverage. This worked perfectly. The nuts came off easily. One did drop into the door but was easily retrieved with a magnetic screwdriver. Now the old mirror pulls right off. You can cut the power cable on the old mirror and pull the two parts through the opening separately. The rest was easy. The replacement mirror has its power cord attached. You simply feed it through the hole in the door. Tighten the three nuts again, plug the new power harness into its receptacle and test. Voila! Mirror works perfectly! Note: there are only 3 screws to remove on the NX200 to get the door panel off. One behind the door handle, one under the small piec of carpet and one under the window controller. The window controller pops out easily. There is no screw to remove on the edge of the door. No need to unplug the power window wiring harnesses either. You can slip the assembly through the opening in the loose door and leave ithe harness attached. Caution: There are many types of wiring harness. Be careful in unplugging them as you must avoid breaking the plastic.

  • @ReveMoto

    @ReveMoto

    11 ай бұрын

    Wow $1000 this is exactly why I make these videos to help everyone save money. Thank you for watching if you need parts for your 🚗 go to www.ReveMoto.com!

  • @marcotrujillo7581
    @marcotrujillo75812 ай бұрын

    Thank you! More explanatory than another video equally long in duration ( for assorted vehicles )!

  • @ReveMoto

    @ReveMoto

    2 ай бұрын

    Thank you we try to make it as descriptive as possible but not too long.

  • @NigelDix-Mypainaid
    @NigelDix-Mypainaid7 ай бұрын

    Great video, you've explained it very well. Now I'm going to try and replace my side mirror, wish me luck... LOL

  • @MrNeilvuong
    @MrNeilvuong9 ай бұрын

    Thank you for a great video.

Келесі