16:33 I wish I would have know about this High Gear spacer 4 years ago, if it even existed. On my 14 XP4, I lost high gear out on a trail. On tear down, I found Polaris never installed the thrust washer (washers don't just disappear) between the gear and the snap ring.....WHATTTTT??? It took just over 2 years of riding to weaken that snap ring into failure, then the high gear slid over as you described in the other video. Thankfully no internal damage with that clip floating to the bottom of the trans! On my next tear down, this car or the next, I will for sure install that spacer. I also 100% agree with upgrading as many bearings as you can!! I went with the Nachi as well (not cryo treated though). Thanks for the ton of info posted here!!

Can’t wait for part 3!

Great job with the transmission videos! I wish you guys would have continued with quality content like this.

Nicely done! Very informative. 👍🏻

Best RZR transmission video out there.

@SXSGarage

3 жыл бұрын

Thank you!

Great Vid! Lots of good information!

This is easily the best series of “how to” videos.

@SXSGarage

3 жыл бұрын

Thank you very much. We have plans for plenty of videos still.

Does installing the ace gears change your low and high or just the ratio in high gear? Thanks for the video 👍🏼

@SXSGarage

3 жыл бұрын

It effects high, low, and reverse. I suggest watching our previous video on how the RZR transmission works. kzread.info/dash/bejne/jKuYqbKsoa-rmcY.html

Cool video! You guys should start using microphones though

@SXSGarage

3 жыл бұрын

The audio for the first 3 videos is only the Gopro audio. The rest of the videos we have already filmed have microphones. Each video after the first 3 has better quality all around.

Could you recommend me gears for my 21 turbo s 4 seater? Running 35 xtr370 now. Also rvs stage 2 tune.

@SXSGarage

3 жыл бұрын

We do a ton of slow technical stuff and snow wheeling so we like our machines geared lower than most. The average person on 35's is happy with the Ace gears and Ranger low reduction which is what's installed in this video. They will work in your machine. You can find them on rockreadyutv.com.

@6669bj

3 жыл бұрын

@@SXSGarage thank you very much

If you only do the Ace 325 in a 900s, do you have to adjust the backlash if you do not remove anything else?

@SXSGarage

6 ай бұрын

No. However, the back lash from the factory is often wrong and the 4 bolt retainer plate is easily deformed and causes issues. It's best to upgrade the retainer plate and adjust the backlash. You would need an output seal to do that but that's cheap.

What do you recommend for a 2021 turbo S running 35” tires?

@SXSGarage

2 жыл бұрын

Most likely the two gear reductions in this video, the Ace 325 and ranger low. If you ever do dunes or put 32's on for desert it will be geared just a little low but tolerable.

@Tattedfire

2 жыл бұрын

@@SXSGarage no dunes. All trail riding and rocks. Could you send me or show the part numbers needed? I’m wanting this done soon. Thanks

Does doing the ACE gear change ratio in high, low & reverse? What does adding the Ranger gear set do?

@SXSGarage

6 ай бұрын

Yes, Ace gears changes high, low, and reverse. The ranger low gear set is just changing the 2 low gears.

@stevebollman

6 ай бұрын

@@SXSGarage thank you for the reply. I have a 19 XP1K 2 seater. I went with the 4 seater high speed reduction and the General low speed reduction.

Wanna do my turbo s4 ?

These gears work in 2021 Ranger 1000xp trans?

@SXSGarage

6 ай бұрын

The ranger has both of those gear ratio's from the factory. You could reduce it a little more by replacing the ace gears with the stage 2 gear set from the Turbo R. They are on the Rock Ready UTV website.

Does it reduce top speed in high gear?

@SXSGarage

3 жыл бұрын

The ace gear reduction does because it reduces all the gears. Any gear reduction after the input shaft gears will reduce top speeds. The ranger low only effects low gear.

Will this combo work on a non turbo xp4?

@SXSGarage

Жыл бұрын

Yes and no. The ace gears work fine. The ranger low does not. Depending on your year it could already have the ranger low ratio and if not, can possibly use the na ranger low off the Rock Ready UTV website which is from a General.

@SXSGarage

Жыл бұрын

The non turbo low gear is part of the input shaft like it mentions in the video.

@travisbarber8786

Жыл бұрын

Thanks for the response! Mine is a 2022 I contacted rock ready and got that I needed. Awesome video and how to!

What's a good way too contact you sir?

@SXSGarage

Жыл бұрын

Our email is sxsgarage@gmail.com

I got the 2016 xpt two seater with 32s do I just need to order the 325 ace thanks

@SXSGarage

2 ай бұрын

That depends on the riding you do. The 16 turbo has the 13% stage 2 and the ranger low gear ratio from the factory. Most people like those gear ratios for 32's in the turbo machines. If you primarily do rock crawling then the ace gears will lower you down some more at the cost of losing your top speed.

@6gatornation

2 ай бұрын

@@SXSGarage that's something I've been thinking about since I bought it new with all the added weight from after market suspension, front and rear bumper , custom roll cage, Stereo system, crypid tires That actually measures 31" in combination with 180hp tune belt smokes in thicker mud in low even though I'm easing the throttle And it must be getting hot because sometimes it explodes in high it hasnt been too bad i'm guessing six belts in 340 hours but I'm fixing to install the 2017 cam and injectors with the whalen 190 tune that goes up to 218hp but I will mainly run 190 mode i'm figuring my belt slippage is going to be worse in high So I'm trying to learn more about the gear and clutching before I start spending a lot of money on parts that don't work😂 i'm thinking that gear is the first place to start You have the best video on the gear reduction I appreciate you responding