thank you so much for not having loud annoying music!
@jortega2228 жыл бұрын
I liked the video, it's self-explanatory!
@atheerismail18389 жыл бұрын
Great video
@nn-js4yg8 жыл бұрын
Thanks great video.....
@kaducostavale3 жыл бұрын
Perfeito!! 👏👏
@Gmtail8 жыл бұрын
I've never seen those brand hand tools before.. What are they?
@marceldeleon12453 жыл бұрын
Cuantos nm se apreta el tornillo ?
@eostrow19638 жыл бұрын
so the supercharger flywheel should have no play whatsoever back and forth?
@VultchInc
2 жыл бұрын
Correct
@MrEvandroxd4 жыл бұрын
👏🏽👏🏽👏🏽
@TheKickBeck8 жыл бұрын
how do you check the slippage of the clutch?
@talusranch990
5 жыл бұрын
You don't need to...... Ha
@ddiana9774 жыл бұрын
bel video ma dovresti controllare con chiave dinamometrica la taratura della frizione dell'alberino
@baldysroost57579 жыл бұрын
A little commentary of what is going on would be helpful. There is no explanation of why or what you are doing to go with the video. I guess if you are a mechanic already, this would not be helpful. Do not understand why there is not a voice explaining what you are doing and why.
@derargentinier8879 Жыл бұрын
Exelente video 👏
@lucabacci62395 жыл бұрын
Lukely is not my supercharger, bearing wrongly installed and torque wrench is usless on that way... i hope it didn’t fail after few hours..
@darnice11255 жыл бұрын
Wathcn 10 min and realized this guy is a hack, Watchh the 3Ft Deep video instead, its done correctly there!
@Tassie19666 жыл бұрын
Do you realise that you have the bearing around on the wrong way on the shaft ?
@kenmanser959
6 жыл бұрын
And someone should tell him that when your torque wrench clicks that's when you stop! Unless it says Walmart on it.
@pauldeanmotorsports7991
3 жыл бұрын
He made a few mistakes not just bearing
@wmabde0
2 жыл бұрын
I agree he did make a few mistakes. One of which is you don't apply gasket silicon loop around the bolt hole, if you expect it to seal tight.
@florytolino39218 жыл бұрын
no he's telling you to send your supercharger to him so he can fix it because you will just f*** it up . they're all specialty tools just for that supercharger and nothing else . one job I do not want to do
@fakegibsonssuck7755
8 жыл бұрын
You can order them through the dealer, hardly special tools....
@glacier_official60017 жыл бұрын
This is NOT a very good video. No explanation at all. Its only a good video if you already know what you are doing. Beezness needs to do a voice over explaining what the heck he is doing.
@pauldeanmotorsports79913 жыл бұрын
Lots of mistakes made
@talusranch9905 жыл бұрын
Repleat with mistakes and hacks
@traviswagner98226 жыл бұрын
camera angle is awful
@MB-ib7pl5 ай бұрын
Horrible video but IF you are mechanically inclined it’s enough to get an idea
Пікірлер: 28
thank you so much for not having loud annoying music!
I liked the video, it's self-explanatory!
Great video
Thanks great video.....
Perfeito!! 👏👏
I've never seen those brand hand tools before.. What are they?
Cuantos nm se apreta el tornillo ?
so the supercharger flywheel should have no play whatsoever back and forth?
@VultchInc
2 жыл бұрын
Correct
👏🏽👏🏽👏🏽
how do you check the slippage of the clutch?
@talusranch990
5 жыл бұрын
You don't need to...... Ha
bel video ma dovresti controllare con chiave dinamometrica la taratura della frizione dell'alberino
A little commentary of what is going on would be helpful. There is no explanation of why or what you are doing to go with the video. I guess if you are a mechanic already, this would not be helpful. Do not understand why there is not a voice explaining what you are doing and why.
Exelente video 👏
Lukely is not my supercharger, bearing wrongly installed and torque wrench is usless on that way... i hope it didn’t fail after few hours..
Wathcn 10 min and realized this guy is a hack, Watchh the 3Ft Deep video instead, its done correctly there!
Do you realise that you have the bearing around on the wrong way on the shaft ?
@kenmanser959
6 жыл бұрын
And someone should tell him that when your torque wrench clicks that's when you stop! Unless it says Walmart on it.
@pauldeanmotorsports7991
3 жыл бұрын
He made a few mistakes not just bearing
@wmabde0
2 жыл бұрын
I agree he did make a few mistakes. One of which is you don't apply gasket silicon loop around the bolt hole, if you expect it to seal tight.
no he's telling you to send your supercharger to him so he can fix it because you will just f*** it up . they're all specialty tools just for that supercharger and nothing else . one job I do not want to do
@fakegibsonssuck7755
8 жыл бұрын
You can order them through the dealer, hardly special tools....
This is NOT a very good video. No explanation at all. Its only a good video if you already know what you are doing. Beezness needs to do a voice over explaining what the heck he is doing.
Lots of mistakes made
Repleat with mistakes and hacks
camera angle is awful
Horrible video but IF you are mechanically inclined it’s enough to get an idea