One of the Excellent video ever found in youtube regarding rx carb

@MotoTravelRide

4 жыл бұрын

Thank you, 🙏

Amazing quality and very educational!! Subscribed to you. Keep the good stuff coming!

@MotoTravelRide

4 жыл бұрын

Thank you for all your support ♥️

Very useful information for low acceleration and high acceleration. In simple words : 5 slots of pin are given, In race = put the pin slot in the bottom. In idle = put the pin slot in the top. In average ( i.e.- not low or high ) put the pin slot in the middle in 3rd slot.

Bro ur the RX god in this earth 🔥🔥🔥..never seen such an intresting and detailed information video..hope u make still more videos like this on Rx...Love frm Andamans❤❤❤

@MotoTravelRide

2 жыл бұрын

thank you brother

Thank you bro your information..it was gift for me in this lockdown :-) keep it up brother...

@MotoTravelRide

4 жыл бұрын

Happy to hear that..

Sir, it was a excellent video. Thanks a lot. Have a nice day.

Excellent brother .. you have given lot of knowledge which is means a lot to me n my rx Thank you.

@MotoTravelRide

4 жыл бұрын

Most welcome brother..glad to know that it helped 🙏

very critical and useful info!! Thanks buddy!!

@MotoTravelRide

Жыл бұрын

Glad it was helpful!

❤❤..correct answer.this is the theory which i was searched for.thynk alot. with well explaination

Lots of love & Thanks Bhaiya❤❤❤❤

One of the best video good luck 👍

Too good really helpful 👍👏🏻

Nice explanation and very proffessional

Praaji tussi samjaate bada accha ho , great hai ji , informative hai 👍👌

@MotoTravelRide

4 жыл бұрын

Thank you bhai, happy to know that informative hai 💐

❤️❤️❤️ Bro really appreciated 🙏🙏🙏

Sooo beautiful soo elegant just listening wow wooww wowww..crystel clear explanation...❤❤❤❤...nice broo...great information for rx 100 biker's thank you

Very informative video thank you

Very good information. Thanks alot

Well explained . Thank you

One of the best video 👌👌👌🙌

Nice breather 🎉🎉🎉 l am from Ethiopia. Tank u for your Sher your experience ❤❤❤

i have semi port so is it ok to increse needle to rich will i get more power

Bro your videos good and useful. Keep going bro.

@MotoTravelRide

4 жыл бұрын

Glad to know that bro..definitely will keep contributing 🙂

Very very helpful. Thanks God bless you

Excellent explanation bro😊

@MotoTravelRide

11 ай бұрын

Thank you 🙂

Good, informative video.Please advice on fluttering problem if possible.Thanks

@MotoTravelRide

4 жыл бұрын

Thank you... Taking note of your query, will soon make a detailed one about it

Superb video bro!🙌

@MotoTravelRide

4 жыл бұрын

Thank you brother... 💐

Super sir clearly u say.. but one doveit why and can we put in second line of thread needle please sir tell 🙏.

Excellent video! My Yamaha DT100 has an aftermarket expansion pipe. Should I adjust the needle position for the aftermarket pipe?

@MotoTravelRide

3 жыл бұрын

Thank you Graham You'll have to go step by step. As Expansion chamber needs carb returning,sometimes re-jetting or even a carb swap to a higher level. - Re-tune the carb after fitting chamber( compulsory) If runs good then fine.. Then go for needle slot adjustment .. seee the response and then adjust the air screw again. All depends on how satisfied you're with the performance.

Extremely nice ...i looking this vedio .. thankyou so much bro🎊🎊🎊🎊🎉🎉🎉🔥🎉🔥🎉🔥🎉🎇🎇🎆

@MotoTravelRide

Жыл бұрын

Most welcome 😊

Good video. Thanks.

@MotoTravelRide

11 ай бұрын

Glad you liked it!

Bro 1983 model Bullet which slot i put this clip in needle?

Great explanation

@MotoTravelRide

11 ай бұрын

Glad it was helpful!

Excellent accurate Information

THANK YOU BHAIYA FOR LIGHTING ....💖💖💖💖💖💖💖💖💎💎💎💎💎💎RX💯

Brother thanks for video , I have one question if I place the ring in second position , you said 3 is the optimum

@MotoTravelRide

3 жыл бұрын

3 is optimum.. . try other places and feel the difference . it's easy thing to to 😉

1 number bhai

Your handwriting is as good as your clear crisp way of explaining things. Thank you. If you can throw some light on the following trouble. Recently I installed VM26 carb on my RX135 (4-speed cylinder 5 speed gearbox and sprockets). It has 130 main jet 22.5 pilot. The bike runs fine at low to mid RPM range, may be even I notice little better performance in those RPMs, but once I blip open the throttle, the engine just behaves like it has been starved of fuel, but obviously more fuel should be the reason. So I changed stock CDI to single map racing CDI hoping to correct the issue. Air filter is UNI. My bike currently in running-in period so I couldn't open the throttle too much, but after the breakthrough, will the mods give better mid and top end performance? I'm not concerned about the fuel average.

@MotoTravelRide

4 жыл бұрын

Thankyou for appreciating the work,and detailed write-up 👌 AFAIK, VM26 has some 200+ size jets, you've got it lowered to 130.. well that's good, but not enough to match the need 4s cylinder with 26mm venturi . It's running lean. ( check the plug ). Up jetting may sort the problem, try switching to 165mains( rx1354s) and see the result. Another suggestion from my side, don't forcible go on high rpms,when you are unsure about the mixture that too under run-in period. Share some pics of plug on my instagram moto_travelxd

@MotoTravelRide

4 жыл бұрын

Switch back to stock cdi and fix the problem one at a time..else it's gonna be a mess.🙂. You already have 3 unsettled mods Carb, jet and Uni and 1 unsettled engine😉

@SuperParuthi

4 жыл бұрын

@@MotoTravelRide Ha ha true. It's three much at a time. Yes as per my limited knowledge the VM26 has a main jet size of 210, but when I opened I noted that it had only 130 main jet. (even our 5 speed carb has 135 main compared to 165 of 4 speed; however, the pilot is much bigger at 22.5, so I believe it's the venturi that makes the difference. You should know better). I bought it online from a reputed seller who claims its RXZ's carb (I believe Malaysian). Any way I exchanged it with 165 main from my 4 speed carb, but the trouble remained. That's why I guessed it may be because of ignition hence changed to the aftermarket CDI. The CDI works excellent combined with my stock VM 22 4-speed carb. Spark strength is very good. I'm riding the same bike for the past 2 decades and it runs on aftermarket performance filters for at least 18 years, K&N, Proton, Pipercross, and now UNI. Any way, lets see what happens after the breaking-in. Thanks again for reading my comment and suggesting :-)

@MotoTravelRide

4 жыл бұрын

You're a pro 😉 22.5 pilot is not problematic for rx1354s,so I suppose Pilot won't be creating any issue,moreover you've good ideling and initial . Primarily it has issues with the main jet or the needle jet which is creating scene .Try setting circle clip to on position down ( from where ever it is) ** before anything pls do plug reading..

@MotoTravelRide

4 жыл бұрын

Moreover I'll say use the stock carb atleast for the run-in period , any how the 26 is uncertain.so a bit risky..

❤ superb

@MotoTravelRide

3 ай бұрын

Thanks 🤗

I love your English dear elder bro

Very nicely explained..pls suggest.. I am using an Oko 28mm on my stock Rx135...I am getting amazing initial pulls..but getting stressed at top ends...mechanic suggests to go leaner as petrol is not effectively burning...will it help to change needle pin settings to leaner..Tnx

@MotoTravelRide

2 жыл бұрын

Hi.. Thank-you for appreciating the work. Will need few more details - jet side on that 28mm, air filter, block size.

@biswanathmohapatra1836

2 жыл бұрын

@@MotoTravelRide tnx for taking out tym for reply..its oko 28mm flat side carb(jet size I never checked)..air filter is moxi..rest all is stock...in general is it correct to set big size carb at lean so that it will act better for a stock engine

@biswanathmohapatra1836

2 жыл бұрын

Block is 2nd oversize of 5s

Nice information, also make video on how carburator work

@MotoTravelRide

4 жыл бұрын

Thank you so much.... I'll try to put it up someday.

For better performance in lower rpm in which slot should we put the ring?

@MotoTravelRide

8 ай бұрын

Above middle level.

Sir rx100 bike ke jeniune part khan Mil sakte h

👍👍Excellent explanation with practical application 👌Very nice video. If there is any video on RX 100 carburetor detailed cleaning, please share the link. Thanks in advance 🙏

@devendrabagul6613

3 жыл бұрын

Can I discuss you personally ? I have some problem with my recently restored RX 100..1990 model bike carburetor.

Can you please let me know how to check the leakage in choke of Rx100 carb?

@MotoTravelRide

Жыл бұрын

Soap water method

I own Platina 2006 model When I try to use choke in cold start bike turns off, while in other bikes rpm raises. By changing the slot will my problem get solved? Moreover while kick starting I've to raise the throttle to start up, Without raising bike does not turn on, and has a very rough idle & bogs.

@MotoTravelRide

Жыл бұрын

Changing slot wot solve this issue, this sound like more of something from the pilot jet circuit and the tuning screw. Get the carb cleaned check both mentioned above for any damages

@JosephJeffrey

Жыл бұрын

@@MotoTravelRide Thank you 🙂

Sir, i need help.some guys are increasing the atomizer holes .what effect will we get ?.do we get leaner or richer when we drill big holes in the atomizer

@MotoTravelRide

Жыл бұрын

we get poor mixture or infact incorrect ratio for proper combustion. NO point of doing those stuffs

Thanks bro ❤

Really informative video! Nicely done, and thanks a lot for making this in English!

@MotoTravelRide

4 жыл бұрын

Thank you 😊 glad to hear that it was helpful. Took note of your words in my earlier video.

@BrattyBiker

4 жыл бұрын

@@MotoTravelRide Thanks!

Rx 100 Ka light badhane Ka koi tarika hai ky plz reply

Very helpful boss

@MotoTravelRide

4 жыл бұрын

Thank You ,glad that it was helpful.💐

Bro super🥰🥰

Super bro

Can use in 4th slote for good performance

@MotoTravelRide

3 жыл бұрын

yes you can

6:15 race - top (top slot or ?), i don't understand, i have rx 135 4&5 speed, so i can beat the 4 speed, its amaze me.. Thank you for precious your video.👍

Bro 5speed chain sprocket vs 4 speed change sprocket video bana

Sir apne clutch bell uper jo video banaya wo bali video kaha gia sir rxg or rx135 ki clutc bell teeth ki uper

@MotoTravelRide

4 жыл бұрын

kzread.info/dash/bejne/moV7uqR9ipSYaJs.html

Hi bro My throttle piston valve is stuck inside ,so the rpm is very high ,.What should I do . Do I need to replace the pin or piston valve . Please help me

@MotoTravelRide

3 жыл бұрын

take out what is stucked ...and then sound why it was stucked .. if damaged then need to replace.

Bro 5s carb se 3 tread athahe Centre Rakna chayiye?

@MotoTravelRide

4 жыл бұрын

Yes bro..centre always. 3 thread centre always 2nd.

I need only milage not pick up ,Can i get some more milage when i place in first slot , is there any problem

@MotoTravelRide

3 жыл бұрын

Depends...mostly no. Whats the present mileage you're getting

@VISHNUGAMER

3 жыл бұрын

@@MotoTravelRide 45+

Sorry Just out of topic one question Does rxz 4 speed and rxz 5 speed have size difference in the that plastic rpm wheel (the wheel which is responsible for the working of rpm meter)?

@MotoTravelRide

4 жыл бұрын

I don't remember it exactly the teeth count difference at the moment.. will update in some time. One thing for sure, there is a quality difference on both the wheels.☺️

@MenofCourage

4 жыл бұрын

Yes,what i felt is teeth count was almost the same but a very slight size different for these plastic wheels

@MotoTravelRide

4 жыл бұрын

no Brigin Bs, It's the other way - a single tooth difference will not make a visible difference of size but it will make a huge difference in the readings..

@MenofCourage

4 жыл бұрын

i was unable to fit my 4 speed plastic rpm wheel in the rxz 5 speed clutch setup, as the 4s plastic wheel was a big one .thus fitted an 5 speed plastic wheel which is slightly smaller

@MenofCourage

4 жыл бұрын

Wot am thinking is if there is an difference in rpm wheels means dont the same difference be there in 4s and 5s clutch primary wheels (even if teeth are same the size would be different for primary wheels?)

It's the same for RX 5 speed carbs as well?

@MotoTravelRide

2 жыл бұрын

Centre one preferred.. there are 3slots in 5s needle.

@shakattakk

2 жыл бұрын

@@MotoTravelRide ok thanks! will performance be affected using a 5 slot needle in a 4tl420 carb? I understand there is a difference in taper.

@shakattakk

2 жыл бұрын

Can you make a video on how to tune the bike for optimum mileage sacrificing some power and also how to tune for optimum power sacrificing some mileage focusing on what could go wrong in both cases. Also which combination of jets to used for power or mileage based on the blocks being used on the bikes. Thanks for your videos, it's a big help for the 2 stroke community and for those of us who self wrench.

Rx100 My bike flattering on full throttle when in slow speed like when climbing hill road if it gain speed about 60/70 no problem....hits smoothly to 80/90/95 what will be do.....is it rich......

@Dead_soon

3 жыл бұрын

Rx100

@MotoTravelRide

3 жыл бұрын

yes rich... lean it by quarter turn. and check

@VISHNUGAMER

2 жыл бұрын

My bike also flattering what the solution

Brother what are the advantages of rich and lean fuel settings??

@MotoTravelRide

2 жыл бұрын

Both doesn't have any advantage... thats the reason we have a thing called as optimum setting..

@TheWess450

2 жыл бұрын

@@MotoTravelRide currently my needle pin is set in 5th slot(most bottom) i,e rich fuel.....will it affect my engine in long run??

My rx100not starting..

I need speed so put in the bottom slat

Bro it depends on piston size?

@MotoTravelRide

2 жыл бұрын

Yes,Piston size primarily. Every oil input is dependent on piston size only.

@salmanulfaris6202

2 жыл бұрын

@@MotoTravelRide my friend 135 4speed running on 1.5 over size piston Where is the position of needle pin ring at top or bottom?

@MotoTravelRide

2 жыл бұрын

Set the needle to 2nd from bottom( pointed side). Then tune the carburetor.

Brother..

Hi

Power section ok..

Hello bro good

@shamsu1003

4 жыл бұрын

Kasaragodian

@KLkl-nb8vs

4 жыл бұрын

U mobile number

Sir, I own aRX135 my bike gets jerk or feeling engine getting off when I speed up to 70-75Km, if I reduce the speed jerk stops and runs smoothly, upto 60 km., Speed no issue, Machanic checked the petrol flow it is working good, problem is not solved, can u suggest what is wrong with bike.. My bike have the another problem with bike running for about 10-15Kms and stop for a while, try to start, it takes 15-20 kicks to start, where as start with choke with one or two kicks. Can suggest to get out these above problems....

Without engine oil .. bike running.. wt happened..

@MotoTravelRide

2 жыл бұрын

Nothing will happen gears will be hard. Better to put oil immediately

Hindi

Bhai hindi me video banao na plz

@MotoTravelRide

4 жыл бұрын

Dono language me hai ye video.. dekho channel pe miljaega

Oo bhai hindi me bolo

English me bat karte ho hindi me bat karke samjo