Thank you for the great comparison! It would be better to stop music and talk a bit :)

Ultracut is awesome!

Konacnooo Alene kraljuuu

@Amddetailing

3 жыл бұрын

Hvala prijatelju😉

Thank you for another educational video; trust me I,m paying attention- I vote for the "EWOCAR PREMIUM WOOL PAD!! just my opinion" thank you, PJP

Great 👍 video

That Rupes DA Coarse cuts really hard. I get it to dust less by starting with four dots of compound on the pad - wool or foam. Microfiber I use eight. You might have been able to use their blue foam pad, or even their DA Fine with their yellow wool pad to remove most of the defects and create a really nice finish.

@JordanWells

2 жыл бұрын

After 8 drops on the fresh mf pad, how much are you using per reload? This stuff dusts like crazy with me, and caused me not to use it for a good while. I started doing 4 drops on a fresh mf pad, and 2-3 per reload and it helped but still dusts a lot for a new compound in this day & age.

@danlc95

2 жыл бұрын

@@JordanWells - Usually three drops. If you play around with amounts, work time, and pressure, you'll get the hang of it. It still dust a a bit, but nothing like when I first started using it. I hated it, but the speed of cut is what brought me back. Now that I gave it a better chance, it works so much better. Be sure not to over work it, and experiment with the amounts. Note that I avoid their priming recommendations, otherwise I have a bad experiemce with it.

@JakeyDill

2 жыл бұрын

@@JordanWells you're getting dust most likely from dirty pads, I use DA course daily at work with both fibre and foam with virtually no dusting.

Top

@Amddetailing

3 жыл бұрын

Tnx

For a heavy cut pad, how does the cool wool perform compared to Rupes wool pads?

@Nqmnqmiiii

Жыл бұрын

awful, worst pads are the hybrid wool and cool wool, no good cutting even worse finish

Pozdrav, može li se za neku budget varijantu koristiti carpro clearcut za poliranje farova(vodobrusni 800 1200 1500 2000 pa poliranje) ili biste preporučili neku drugu pastu u pitanju su farovi škoda Fabia 1

@Amddetailing

3 жыл бұрын

Mozes koristiti koju god hoces grubu pastu poslije brusenja farova

@nikotiin23

3 жыл бұрын

@@Amddetailing hvala na odgovoru

@dejanilibasic3316

3 жыл бұрын

@@nikotiin23 ako ćeš jeftino uzmi fareclu g3 premium i uradi dve ruke,jednu grubim a drugu finim sundjerom ili mf

Ja manje vise koristim Rupes plave wool pads ali uvek prime them na početku.. Jos nisam našao bolji pad za cutting. Imaš li neke druge sugestije za bolji cut? Videcu kako ovaj HC4000 i njihovi Zvizzer padovi rade..

@Amddetailing

2 жыл бұрын

pasta radi fenomenalno samo je moras pretvoriti u uljnu fazu i nemas problema ,nema prasine i lagana je za rad. Hvala na clanstvu i ako sta treba stojim na raspolaganju

@autoprofinish3453

2 жыл бұрын

@@Amddetailing ove nedelje sam uradio crni jeep sa HC4000 pastom i vunenim padovima i stvarno je fenomenalno.. Hvala sa predlog.

@Amddetailing

2 жыл бұрын

@@autoprofinish3453 nista sretno u daljnjem radu😉

Can you tell me if ewocar heavy cut plus performs better than both of these compounds?

@Amddetailing

2 ай бұрын

yes

form your video I would go for CARPRO just for the sake of the compound dust.

No second chance for the first impression.

Pozz alene koja bi bila po tebi najbolja razmera alkohola 96% I destilovane vode za odmascivanje panela od paste

@Amddetailing

2 жыл бұрын

Pozdrav 30:70(alkohol/ destilovana voda)

@bojangajic6762

2 жыл бұрын

@@Amddetailing hvala, živ bio 😁

@siki677

9 ай бұрын

​@@Amddetailing70% alkohol ,30% voda tako si mislio

@Amddetailing

9 ай бұрын

@@siki677 ako je 98% alkohol ide 30 ili 40% alkohola ostalo voda

@siki677

9 ай бұрын

@@Amddetailing imam i ja etanol 96% ,mislio sam 60% alkohola i ostalo destilovana voda ali moram te onda poslusati na ovakav nacin da pravim razmeru

Hoće li biti video za roto varijante? Pozz

@Amddetailing

3 жыл бұрын

Pozdrav,nevjerujem jer ce se opet testovi ponavljati skoro isti

Ovde nema greske sa obe paste, koju bi ti preporucio pre za pocetnika, kojeg proizvodjaca od ta dva

@Amddetailing

3 жыл бұрын

Rupes u poredjenju sa tom bolji je ,a mozes i zvizzer HC4000

With what product you degrese?

@omedonnie

2 жыл бұрын

I would suggest any IPA mixed solution. For example Carpro Eraser.

@dle9164

2 жыл бұрын

@@omedonnie thanks

As soon as I saw you not load the wool incorrectly I moved on.

@amounifnd

2 жыл бұрын

Thats video from Esoteric detailing is a great watch. Priming Vs No priming the Legs MF pad. The No Priming won out each time. Better Cut and higher gloss. This test was consistent and a great review.

@bluegrasskid4835

Жыл бұрын

Why don't you explain to him how he should have loaded the wool pad to be helpful instead of a douche.

No hay nada que pulir, 😅😅😅

As said before by others your test is wrong in so many ways. You overworked the rupes ( which is a short cycle compound, after 45s all there is nothing but carriers ) making it dust everywhere. You didn't prime the pads correctly and the test should be made with the same pad

Auuu al prasi Rupes... Ona stara nije toliko prasila...

@Amddetailing

3 жыл бұрын

Ne prasi ni ova nego nije pad bio dovoljno cist

Zasto rupes plavu ili nebitno koju boju fepa koriste vise mikrofiber,nego onaj obican sundjer da kazem,i dosta su odusevljeni i izgleda bolje daje rezultate sa mikrofiber nego sa obican sundjer od rupes pricam

@Amddetailing

2 жыл бұрын

Sve zavisi od tvrdoce laka tako se i bira sa cime poceti a spuzve ne mogu raditi dobro grubu fazu poliranja samo vuna

@nikolazivkovic9084

2 жыл бұрын

@@Amddetailing nista hvala drug,ce vidimo kako i sta 😁

completely wrong priming technique, completely different pads, not only used the DA coarse incorrectly, but overworked it as well... This test is 100% misleading.

@omedonnie

2 жыл бұрын

I agree this guy has no idea what he is doing.

Not quite precise as you haven’t primed the wool pads correctly

@amounifnd

2 жыл бұрын

Amazing how people skipped the fact that he cut the paint both times ??? Priming often just matts down the fibres quicker. This probably sums it up the best kzread.info/dash/bejne/dq5-rKOPXbOehdo.html

Stop with the terrible music. Seriously.

@Amddetailing

Жыл бұрын

okay, suggest the music that I should put without copyright

@statusquoreject

Жыл бұрын

@@Amddetailing I feel your videos would be much better with no music and more narration from you. I’d much rather hear you talking about your process, thoughts, tips & tricks as you work. I feel that would provide more value to your viewers than music and you won’t have to worry about copyright issues.