Nicely put together

@JOEZEP54

4 жыл бұрын

Much appreciated. Hope it is of help. Stay safe, Joe Z

Same thing happened to mine! just removed that kill switch wire and it fired right up. crazy. thanks for your video. saved me a lot of time

@JOEZEP54

3 жыл бұрын

Logan Cameron, You're welcome, I am glad this was of help .And thank You for watching and taking the time to comment. Logan Cameron I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links.*** Thank you for watching and I really appreciate your support. Stay safe, Joe Z

@jazalessandro3094

3 жыл бұрын

So how did you turn it off after then? lol

@JoseNunez-yn4tz

3 жыл бұрын

When you removed that kill wire did the muffler seem to get extremely hot quick or is that normal?? Because mine was having the same problem i removed the wire and it fired right up

If the wire is fine,all the way back to where it is connected,then its the coil pack! Good job Jo!

@JOEZEP54

3 жыл бұрын

Jaz Alessandro, Thank You for watching and taking the time to comment. . Constructive comments always welcomed & appreciated. Jaz Alessandro I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest Be sure to 👍, share and subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

thanks for your time and info much appreciated

@JOEZEP54

2 жыл бұрын

You're welcome, gad it was of help. And thank you for your support. Stay well, Joe Z

most lawn tractors have several safety switches couldn't it be one of those !! Thanks Joe !!

@JOEZEP54

4 жыл бұрын

Hi Jeff, Yes & it usually is. Sometimes though as simple as not having the brake on , the blades turned off or even having it in gear. This time for me it was the wire. Thank you for stopping by & adding information to this video. Stay safe, Joe Z

@davidjohnson4343

2 жыл бұрын

Absolutely, the first thing to check. Reverse switch, mower engage, switch, seat switch, and maybe a brake switch.

@Mike-su8si

2 жыл бұрын

@@davidjohnson4343 they are buttons though i removed all of them off of all my driving mowers because they're more trouble

@Mike-su8si

2 жыл бұрын

It probably was then if his coil is bad he'll know it when it shuts off while he's using it then let it cool down and quickly drive it back to the shed before it shuts off again from overheating

Great video Jo!

@JOEZEP54

2 жыл бұрын

Thank you Nate. I really appreciate your comment. Hope it helped you out. Nate I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share and subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Nate Polmateer I just want to mention If you haven't installed the TubeBuddy browser plugin yet, to help your channel grow Just go to my favorite tool for channel growth Tube Buddy. Now You can use it too, here's my affiliate link to the Free versionwww.tubebuddy.com/joezep54 Start with the free version, yes it is free to not only to down load but to use. Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

Thanks that’s exactly what was wrong with mine. Video helped tremendously

@JOEZEP54

4 ай бұрын

You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. @MichaelWilliams-cm4qo I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content would help me to reach other viewers that may also find this channel useful or entertaining. Stay safe, Joe Z

Thanks for sharing this

@JOEZEP54

2 жыл бұрын

Tom McLean, You're welcome, I am glad this was of help. And thank You for watching and taking the time to comment. Tom I read your "ABOUT" on your channel. I can understand your dislike for adds, and I do not care for them myself. That said I am trying to go fulltime with this & need an income not only for the obvious but to upgrade my equipment when possible. I mentioned this so you know the why. Hope you get to enjoy some more of my channel I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share and subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 >>>>>>>>>>>>>>>>Some more adds of sorts.

From Paul. Engine will turnover, but won't start. I replaced the ignition coil, spark plug, cleaned flywheel, adjusted everything, but no fire. Starter fluid doesn't help. 11 hp Briggs 35 years old.

@JOEZEP54

3 жыл бұрын

Hi Paul, Have you checked the compression. If you adjusted the vales your rings or valve guides may be shot. Also more of a push mower issue but if the flywheel key is slightly off it will affect the timing. Let me know if this was of help. Joe Z

thank you so much my mower has the same problem im 13 i have my buinuss going and this helped me a lot

@JOEZEP54

3 жыл бұрын

Glad it helped! metriox, You're welcome and thank you for watching and taking the time to comment. metriox I just want to mention If you haven't installed the TubeBuddy browser plugin yet, to help your channel grow Just go to my favorite tool for channel growth Tube Buddy. Now You can use it too, here's my affiliate link to the Free versionwww.tubebuddy.com/joezep54 Start with the free version, yes it is free to not only to down load but to use. Let me know if I can be of any help. Due to time I cannot always video projects that I am working on. If I do not have the video I may be able to direct you to another channel that does. Again I hope you get to enjoy other videos on my channel as well. . Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of the above affiliate links. *** Thank you for watching and your support I really appreciate it.*** Stay safe, Joe Z

Love the Boston Aaacent!

@JOEZEP54

10 ай бұрын

Thank you, Be sure to subscribe & ring that bell to hear more LOL Stay well, Joe Z

I took it for granted too

@JOEZEP54

Жыл бұрын

Thank you for stopping by. We are always learning something new, then we relearn what we forgot LOL. Stay well, Joe Z

It was the “spork” and you took it for “granite”... don’t forget the “wier”. JUst joshing, good video.

@JOEZEP54

3 жыл бұрын

So you were paying attention. Hope you were able to get you mower started.

good video ed

@JOEZEP54

3 жыл бұрын

ED EDMUND, Thank you. I appreciate you taking the time to comment. ED EDMUND I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. If your are inclined to do so be sure to 👍, share & subscribe Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

Thx did what you side and it work thx so much but what do I do with the plug now ?

@JOEZEP54

2 жыл бұрын

You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. The plug ??? BSM SPORT CARDS I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Your support is not required or expected but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and using the following links do help. Thank you for your support and using the links provided to make your purchases. Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

Same engine I have. What a piece of garbage. Nothing but headaches with this thing. Thanks for the pointer

@JOEZEP54

Жыл бұрын

You're welcome, I hope this was of some help. And thank you for watching and taking the time to comment. Some of these units need more attention than others. Even the higher price units have issues. @FaceForwardd I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content do help. This is always appreciated. ******* Thank you for your support ******** Stay safe, Joe Z

I have an old 2008 lawn tractor and it won’t keep firing unless I constantly run the starter. I’m getting spark and I’m getting fuel. After I attempt to start it a few time the cylinder and muffler gets hot, but it still will not start. I’m not sure what the deal is here but it has been some years since this mower has been used.

@JOEZEP54

2 жыл бұрын

I had one that had a valve stuck after sitting. I would first do a leak down test. My first thought would be the valves. Next it could be a shear pin Although you are getting gas the carburetor may need an adjustment. Do you have fresh gas? Old gas would have water in it & that would keep it from starting. Do not keep it going with the starter or it will burn the starter out. Let me know if this helped you out. Stay safe, Joe Z

I have acrank, but no start issue my self. i used it a few months ago and it ran fine. The next day it ran fine, but after a short while it really lost some get up and go by going very slowly back to the garage and now it won't start. My mom's got a large yard and the normal grass guy has been ill lately. Would dirt in the car make it act like this? Excellent video btw.

@JOEZEP54

2 жыл бұрын

poppaluv, It could be the cause hard to tell without being able to go through it. Check the fuel line, disconnect after the fuel filter to see if fuel runs out or just trickles out, BE CAREFUL. If the gas is running out freely your filter & line are ok. If it starts & then dies open the gas cap & put it back on loosely to see if it will run. If it does the gas cap vent is plugged. Check your spark plug. Look for oil or carbon build up or if it has a good spark. It can also be blown head gasket. If so this is not a difficult repair. You can check the compression with a pressure gauge, if you do not have one AutoZone, Advance Auto have lenders. Let me know if any of this helped you out Stay safe, Joe Z

What size of socket would I need to remove spark plug in a yard machine just like this one?

@JOEZEP54

5 ай бұрын

Thank you for watching and taking the time to comment. @bad_blue_3499 I no longer have this unit and sorry I do not remember the size. I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content would help me to reach other viewers that may also find this channel useful or entertaining. Stay safe, Joe Z

Thank you so much same situation changed everything new battery and I noticed that the battery shorted out so there ya go lol

@JOEZEP54

Жыл бұрын

You're welcome. Thank you for taking the time to comment. Be sure to visit again. Stay safe, Joe Z

That's so funny I had mice build nests in the same spot. So I changed the carb it's was 15$ on eBay but still nothing. It was that same kill wire.

@JOEZEP54

3 жыл бұрын

Those little buggers keep me busy. Working on a Snapper rider that has been sitting for a little over 2 years. You should have seen the condo they built in this one. But not 1 wire was chewed on. Just a big mess. Hey Mr. J if this video was helpful consider subscribing to my channel & hitting that 🔔 not to miss any of my new videos as I up load them. Thank you for watching & taking the time to comment. Stay safe, Joe Z

Yore Aksent has me homesick, dere. When you said you would "Sand Down" the contact, I heard you say "Sandown", which is in NaHampsha, by da way.

@JOEZEP54

Жыл бұрын

Hope this video was of help with your mower & brought you some good memories of home. Thank you for watching & taking the time to comment. Be sure to come back & visit my channel again. Stay well, Joe Z

Can I pull the kill wire, run it and cut the grass, and then worry about fixing it later? Can the thing mow my lawn for a few hours with a kill wire unplugged?

@JOEZEP54

Жыл бұрын

This would be a dangerous way to go. You will not be able to shut in down with the key & all the safety switches would be disabled. If you should flip the mower or start it with the blades on it would be a serious hazard. It will run but is dangerous. & I say do not mow with the kill wire unplugged. Thank you for stopping by. Stay safe, Joe Z

How can you find the numbers to buy carb. Kit or carburetor for 13.5 hp briggs and Stratton lawn tractor

@JOEZEP54

2 жыл бұрын

Check the carbureator, it will have the name & model # on it. If you cannot read it or do not have it, get the engine #s & go to the Briggs & Stratton site, this is the first place I would check out. Parts Tree or other sites that sell parts will also be of help. Let me know how you made out. Stay well, Joe Z

I have the spark and starter works fine , fuel is getting too but still no start

@JOEZEP54

2 жыл бұрын

Thank you for stopping by. A couple of items to check: is the spark bright, I had one drive me bananas, changed the plug & NP since. Is the gas fresh, make sure no water in gas. Did you check compression? Does your engine have OHVs? They may need adjustment. Next & often over looked is the woodruff key. Check to see if it is sheared. If it is you would still get spark but at the wrong time. Let me know if this was of help. Stay safe, Joe Z

Mine has been purring along all summer like a dream. Gassed up this morning started it up and ten seconds later it began to buck and snort and cut off. After several attempts to start now it's just spinning. Even starter fluid and gas in carb don't help. I'm stuck. Any ideas?

@JOEZEP54

10 ай бұрын

Hi Patrick, start with the basics. It is not starting with started fluid so I would next check for spark. If there is not any spark check the kill wire to the coil. Doing this you have to be very careful, disconnect the kill wire from the coil & then try to start. If it starts you will have to pull the spark plug wire to stop the engine. Use a pair of insulated pliers to pull the wire. If it does not start change the spark plug. If still no start / no spark I would next change the coil. Let me know if this was of help. Stay safe, Joe Z

So if it is that wire, ( haven't checked mine yet) is it ok to run it without that wire on?

@JOEZEP54

2 жыл бұрын

DANgerus 1399, Thank You for watching and taking the time to comment. It will run without that wire on but all the safety switches will be disabled plus you will not be able to shut the engine down with the key switch. This would be a very dangerous condition. Repairing or replacing that wire is not difficult & is the safe way to go. DANgerus 1399 I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share and subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

Do anyone know what the oil capacity on these engines. because I bought one and the dipstick is missing.

@JOEZEP54

Жыл бұрын

They're all about the same but to make sure get the model & serial #s. Then we can get the accurate capacity. These units can have different engines. Stay well, Joe Z

Hi, my tractor will only start when I put gas in the carburetor. Any idea why? Thanks

@JOEZEP54

3 жыл бұрын

It sounds like the engine is not getting gas to it. Check the easiest first. Fuel filter--fuel line-- if all ok & fuel is flowing then a good carburetor cleaning. How old is the gas in the tank? Let me know if any of this helps.

my yard machine will start with starting fluid but cuts off as soon as the starting fluid burns out, but wont start without it?

@JOEZEP54

2 жыл бұрын

Antoine Finch, Thank You for watching and taking the time to comment. It sounds like it is a fuel flow issue. First check to see if gas flows out of the fuel line. If it does, I would then pull the carburetor to clean it out. I am "assuming" the fuel is fresh & your choke is working properly. Let me know if this helps Antoine Finch I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share and subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Antoine Finch I just want to mention If you haven't installed the TubeBuddy browser plugin yet, to help your channel grow Just go to my favorite tool for channel growth Tube Buddy. Now You can use it too, here's my affiliate link to the Free versionwww.tubebuddy.com/joezep54 Start with the free version, yes it is free to not only to down load but to use. Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

Happened to me. Cranks but no start. Very dirty air filter. Changed and stared right up!

@JOEZEP54

7 ай бұрын

Thank you for watching and taking the time to add this additional information. There are several causes for a Cranks but no start and we just explained 2 of them. I hope your comment & this video will be of help to some that may view this video. @wvahillbillyok I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content would help me to reach other viewers that may also find this channel useful or entertaining. Stay safe, Joe Z

I'm looking for some input if you'd be kind enough to give me your opinion. It's a briggs and stratton single cylinder. When I crank I'm not getting spark however when I let go of the key and the momentum of the engine continues to spin it begins to spark. So no spark in start position do have spark in run position. Checked all safety switches (good), pto switch new, ignition switch new, carb solenoid functions normal. Any thoughts?

@JOEZEP54

2 жыл бұрын

This one has me stumped as well. One suggestion is to compare the ignition switches. Even though the tabs fit the wire end make sure they are for the same functions. I never ran into this & will ask around. I will let you know if I fine any solution for this. Also let me know if you find out first. Stay safe, Joe Z

@tntrackey

2 жыл бұрын

@@JOEZEP54 just an update because I'm stupid. The pto switch was bad at one point and I swapped it and fixed this problem once. Long story short I parked it in the garage without setting the parking break. No brake no spark apparently.

@JOEZEP54

2 жыл бұрын

@@tntrackey I am glad you figured it out. Like I mentioned earlier, it had me stumped. Thank you for the update 👌You should be able to start it by just pressing the break down when starting. tntrackey hope you get to visit my channel again. Your questions/comments are always welcomed. Enjoy this summer, Joe Z

I picked up a free John Deer riding mower. I need to fix it, the previous owner said they took it in for a service and it ran for about an hour and just quit, then the owner took it apart (mainly wiring ) and it has been sitting in their garage for a few years as they never fixed it... L+

@JOEZEP54

3 жыл бұрын

This could be a project, 2 cases of it being "worked" on. If you can get a wiring schematic it may pay just to rewire from scratch. Also if yo disconnect the kill switch wire you can check to see if you have spark by jumping the starter then proceed from there. Let me know if I can be of help.

smart to check your plugs.

@JOEZEP54

2 жыл бұрын

Thank you for watching & taking the time to comment. I hope this was of help. king james488 I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Your support is not required or expected but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and using the following links do help. ******* Thank you for your support ******** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

@kingjames4886

2 жыл бұрын

@@JOEZEP54 did you copy and paste that? lol. didn't help much really, but I thought I'd stay positive. my problem was just some water in the carb or something... cleaned it out and it worked... for about 10 min until a spindle fell out... more things to fix!

@kingjames4886

2 жыл бұрын

@@JOEZEP54 also there's another weird issue I've had that this wouldn't have covered which you may want to look out for... if your battery is half-bad is will act as a massive capacitor and totally drain the electrical system. I've had them charge up to like 11.5-12v and when you hook it up it only has enough juice to click the relay, even hooking up booster cables won't get it going as long as it's connected to the bad bat.

@JOEZEP54

2 жыл бұрын

Thank you for staying positive 😂 I use Tubebuddy to help with the videos & one of the features is a section that you can type in your replies. I change it around from time to time. But I always try to respond to the replies I get as soon as possible. My take is if a viewer can take the time to comment I should do in kind. Spindle fell out or broke off? I have gotten several that the spindles broke off. Some had a 3 bolt mounting others a 4 bolt.

@JOEZEP54

2 жыл бұрын

@@kingjames4886 Thanks for the tip. I had one that would not start with the jumper pack attached to the battery, but when I disconnected the battery it started with just the jumper pack attached to the wires. This confirms you statement.

Water will not hurt that engine.

@JOEZEP54

5 ай бұрын

@charleskuder3968 Thank you for watching and taking the time to comment. Water usually not an issue. These engines can & do take a lot of abuse. Thank you again for your support. Stay safe, Joe Z

If you don't live in Boston I'll eat your lawnmower's air filter.. Thank you for a very helpful video.

@JOEZEP54

2 жыл бұрын

You're welcome & thank you for watching & taking the time to comment I am not from Boston but from the Bronx NY. Funny a couple of other subscribes thought I was from the Boston area. Oh I need your mailing address to mail you my air filter LOL. Wayneasiam62 I have other videos on my channel that may be of help or just entertaining. Your comments, likes, sharing & subscription are a big help & appreciated if you are inclined to do so. Stay well, Joe Z

I have a Briggs & Stratton platinum 21 hp craftsman mower and I have checked a couple things like it said to spray starting fluid and if it starts but does that means that you have compression and spark and that it’s in your fuel system so I replace the fuel line, the fuel line cut off valve fuel filter and still the same thing. Any suggestions on where I should go from here? Thank you very much.

@JOEZEP54

Жыл бұрын

I would look into the carburetor. Check for old fuel with water in it. Debris or corrosion if it is a metal carburetor. Do a through cleaning. Yes you have compression & spark, but this does not mean you have have sufficient compression. If it starts after cleaning the carburetor & runs right you're good to go. If it smokes or lacks power you may have other issues. Let me know if the carburetor cleaning got you going. Stay safe, Joe Z

@carolinewells4355

Жыл бұрын

@@JOEZEP54 Thank you so much Joe for your thorough reply. It makes sense, its hard for me to lean toward the carburetor because I had it replaced with a new one. stuff that you winterize your gas with, and ran it through the motor like it instructed before storing. Also I removed the part that is under the carb(prevents backfire I believe) that has a tendency to get gummed up and it was perfectly clean as was the metal shell that covers the bottom of carb. Looked brand new, is the fuel line or whatever line it is, that runs from the fuel pump to the carburetor looks very worn and degraded. It is a size smaller than the 1/4 inch fuel line I used. Didn’t notice the size of the line because it was so degraded.

@carolinewells4355

Жыл бұрын

@@JOEZEP54 my comment was supposed to say my carburetor was replaced last year with a new one. Can I get gummed up in one summary of mowing?

@JOEZEP54

Жыл бұрын

You're welcome. Caroline, it may still be the carburetor. But do this with caution, disconnect the fuel line from the fuel pump to the carburetor. Leaving the fuel line connected to the fuel pump and into a container. Again use CAUTION!!! start the engine & check the flow from the fuel pump. If it is strong you eliminated 1 possibility if not you need a new pump. You can remove the anti backfire solenoid and connect it to the battery. Check if the little plunger moves down when charged & up when you remove the batter. Let me know if any of this was of help. Stay safe, Joe Z

@carolinewells4355

Жыл бұрын

@@JOEZEP54 I’m thinking that I may just call the mobile mower mechanic because it might be above my expertise lol thank you so much for the help so far I’ll let you know what it is when I get it fixed

U can use a piece of milk jug plastic to set the coil width if u didn't no

@JOEZEP54

2 жыл бұрын

Thank you for watching and adding a tip. I usually use a business card but will check that plastic jug. Stay safe, Joe Z

I got the same mower… my problem is basically the same. I would cut the lawn after I was down Id shut it off then if I seen I missed a spot and wanted to go over again it wouldn’t start. Yet it ran fine for 45 mins. Now i started cutting lawn after 1 month or so without use, and it stalled 1 minute in and won’t turn over. ??? Could it be same issue ?

@JOEZEP54

Жыл бұрын

It could be but from what you described it sounds like a bad coil. Next time you try to start it check for spark or if it starts then stalls check for spark. A coil that is on its way out may run for awhile get hot then shut down or not start at all. If you have spark & it will not start check fuel delivery. A clogged gas cap can cause a stall when air cannot be replaced into the fuel tank. Let me know how you did with this. Stay safe, Joe Z

@crokkadoodledoo9956

Жыл бұрын

@@JOEZEP54 eh … brought it to shop. Said it was ignition module ??? Charged a shit load. Better off with a tune up > new belt, new fuel filter, carb clean, oil change would of cost less.

@JOEZEP54

Жыл бұрын

@@crokkadoodledoo9956 It gets expensive at the shop. Like any other trade some are well worth it & some not so much. That said did this take care of the issue? How is your mower running?

there is a small groment plugs into plactic fuel tank that hose connects over time they get gloged new one about $2.00 causing fuel issues to check disconect hose from tank to fuel pump fuel will flow freely if ok reconn hose now remove hose from pump to carb spin eng fuel will flow good from pump if ok if not replace pump some also have a filter check too some people have flooding after altering solenoid reather than a cut off switch just put a loop in fuel line pump to carb

@JOEZEP54

Жыл бұрын

Thank you Frank for stopping by & adding this information. Stay safe, Joe Z

So how did you replace the kill wire?

@JOEZEP54

2 жыл бұрын

Hi Bob, Thank you for stopping by. On That mower I just followed the wire back to find the short. Did not have to replace it. There was plenty of wire so I cut where it was shorting out. Spliced it together & used heat shrink tubing then made sure it was not rubbing against anything. That kill wire goes up to the ignition switch. When you shut the mower down it shorts the coil to ground. Stay safe, Joe Z

@vtwin03

2 жыл бұрын

@@JOEZEP54 thank you . Hopefully my issue is as simple as the kill wire. Thanks for the video and follow up

@JOEZEP54

2 жыл бұрын

@@vtwin03 You're welcome. Hope this helps you out. Let me know how you make out with your mower.

i have a riding lawn mower crank and it has spark but dont star

@JOEZEP54

Жыл бұрын

Manuel, are you getting gas into the engine, if so is the gas fresh? Check the bowl under the carburetor to see if there is any debris or water. Let me know if this was of help. Stay well, Joe Z

I have a 2014 yard machines start with starting fluid but dies right away. Is the bowl on the botton of the carburetor should be full of fuel? When i disconnect the hose fuel comes out but the carburetor is dry. Can you help me

@JOEZEP54

9 ай бұрын

Just want to make sure I understand. 1) when fuel line is disconnected fuel flows from it 2) there isn't any gas in the carburetor bowl. If this is correct is the fuel flowing after the fuel filter or before it?

@omarargullin2313

9 ай бұрын

@@JOEZEP54 1)yes fuel flows from the line. 2) NO Gas in carburetor bowl. 3) and after the fuel filter.

@JOEZEP54

9 ай бұрын

Sounds like the fuel is block from going into the carburetor. When you remove the bowl inspect the float, more than likely the needle is stuck, or just may be some small piece of debris stuck, If not any of the above check the seat. Look to see if it swelled closed. Let me know what you find.

@omarargullin2313

9 ай бұрын

@@JOEZEP54 and to add a little more to story. It only starts when i put some starting fluid liquid other wise it just cranks but not start. The more fluid i put in the little longer it last running and is not even more than 2 seconds.

@JOEZEP54

9 ай бұрын

@@omarargullin2313 This shows you have spark & compression. Fuel just not getting to the engine. Do the checks I mentioned earlier.

Joe I subscribed but it won't let me get notified of new videos. I'll keep a eye out for em anyhow

@JOEZEP54

4 жыл бұрын

Thank you, your support is much appreciated! I should have a video up in a day of so. Working on a couple of projects & which ever-one gets done first I will post. If you still do not get notified let me know & I will see what can be done.

Thanks Joe this video helped me out. I may grow hair back on my head where I scratched it bald. 😂

@JOEZEP54

Жыл бұрын

LOL You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. Zombewerks I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content do help. Another way to Help Support The Joe Z Channel at no cost to you is by using my affiliate links or just go to: www.amazon.com/shop/joez An affiliate advertising program is designed to provide a means for sites to earn advertising fees by advertising and linking to amazon, that helps me to continue producing videos. Thank you for your support and using the links provided to make your purchases. This is always appreciated. ******* Thank you for your support ******** Zombewerks I just want to mention If you haven't installed the TubeBuddy browser plugin yet, to help your channel grow Just go to my favorite tool for channel growth Tube Buddy. Now You can use it too, here's my affiliate link to the Free versionwww.tubebuddy.com/joezep54 Start with the free version, yes it is free to not only to down load but to use. Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

@jabsjc

Жыл бұрын

@@JOEZEP54 I’ll hit ya with h a sub

That it Joe , always test , never assume .

@JOEZEP54

4 жыл бұрын

You'd think I would have learned by now LOL. Hey Chris thanks for viewing & taking the time to comment. I am always looking for other channels to correspond with. Do you post any videos? If so maybe we can collaborate on a few together. I did go to your channel but is has ''"This channel has no videos."" If you do have some videos this may be due to how you have your channel set up. Stay in touch & be safe, Joe Z

buy a can of starting fluid (auto stores) find filter on carb put a squirt into filter dont need to take filter off now try it it starts running about 1 min then stops it a fuel problem it could be fuel pump or fuel filter also some carb. has a wire to a small solenoid bottom of carb if that wire is off it will not start no fuel in carb when you turn switch on 12v operates that small solenoid to let fuel in carb this is what stops engine when you turn switch off if you have this problem may need help with carb. repair nd replace

@JOEZEP54

2 жыл бұрын

Hi Frank thank you for adding this information, Even though the problem was not with the carburetor in this video it maybe for another viewer. Hope you get to visit again. Stay safe, Joe Z

@timothyholmes9556

2 жыл бұрын

My John Deer, been sitting all winter in the garage in New York State. Cranking but won't start 👀 did is sparkplug test and everything was sparkling...🤔 the carburator

@JOEZEP54

2 жыл бұрын

@@timothyholmes9556 Thank you for stopping by. It may be the carburetor. Follow the comment above from Frank Davidson . If you do not have starting fluid, gas, carb cleaner just about anything flammable will work. You are just checking to see if it will fire up. Be careful, Joe Z

Hi my mower would not start it just clicked so i replaced the solenoid and now when I turn the key it cranks but wont start and the fan spins really fast what should I do.

@JOEZEP54

3 жыл бұрын

Did you check to see if it has spark? You can spray a little carb cleaner into the carb & try starting. If it runs until the little carb cleaner is burnt up you have a fuel delivery issue. Stay safe, Joe Z

I'm kinda in the same position, but I have spark. Cleaned the carb, changed gas, plug, fuel filter, air filter etc. Still not turning over :( it's louder than normal, but I just figured the muffler finally rusted out, no holes on the outside. Not a knocking, just like glaspacks lol

@JOEZEP54

2 жыл бұрын

RagingKoala, When you say not turning over, what do you mean? Cranking & not starting? Not cranking? I am confused because you say it's louder than normal.

@lynx50187

2 жыл бұрын

The shaft key had sheared so it was out of time I found. Put a new key in it and the flywheel snapped (but it did start lol) think I am just gonna take it in.

@JOEZEP54

2 жыл бұрын

@@lynx50187 Even if you hit something solid, tree root, stump, brick pipe the belts should have slipped before the pin went. Unless you hit it really hard & it jammed up, maybe. Flywheel snapped reinstalling? Look around on face book, craigslist whatever is in your area. You may find a decent rider for less than the repair or a decent engine you can swap. Let me know how you make out. Stay safe, Joe Z

@lynx50187

2 жыл бұрын

Didn't hit anything either. Seems the key sheard after I reinstalled the flywheel. After replacing the alternator. Installed a new key,started it and it must of backfired hard enough to break the flywheel. I will let you know what they say

@JOEZEP54

2 жыл бұрын

@@lynx50187 If you did not torque the nut holding the flywheel tight enough, that could cause the key to shear.

98% of the time with no start issues they are electrical. I learned this the hard way and costly as well.

@JOEZEP54

4 жыл бұрын

Joseph M Than you for stopping in & taking the time to comment. Yes the issues are usually between electrical or the carburetor. Hope this was or help. Stop by again when you get a chance & stay safe. Joe Z

@dukeman7595

4 жыл бұрын

@@JOEZEP54 Yes it was Joe Z thank you..

@JOEZEP54

4 жыл бұрын

@@dukeman7595 You're welcome 👍

@MB-pt3gt

3 жыл бұрын

I have a craftsman riding mower, cranks but won’t start, even after a new carb and a new coil pack and new gas , has spark and oil and gas. Must be a electrical issues? Not the kill switch , that’s good

@matthewgarrett3432

2 жыл бұрын

I have a craftsman new carburetor and fresh gas. Plenty of spark. New flywheel key. I just don't understand anymore. I have adjusted the valves and got it fired right up before I shredded the flywheel key. Now I can't get this thing to do nothing but crank.

i keep a spray can starting fluid very use full will usual start a balky eng -- no need to remove filter just spray 1 shot into filter try you will love it

@JOEZEP54

Жыл бұрын

Just be carefull not to use too much too often, it can cuase engine damage.

Ran riding mower out of gas, put more gas in and won't start. Drained fuel with new fuel and still won't start. My son pulled off air filter and put his hand over the opening and it tried to start but when he removed his hand it died. Fuel solenoid maybe?

@JOEZEP54

2 жыл бұрын

Check if the choke is engaging. Next check fuel filter. Next remove the fuel line, let it pour into a container, is gas running freely or just dripping? If all is ok there may be an issue with the carburetor. Sediment in the bowl, blocked jet, bad o ring or seat. Let me know how you make out with this. Stay safe, Joe Z

@meintsgwen

2 жыл бұрын

It was the fuel solenoid

@JOEZEP54

2 жыл бұрын

@@meintsgwen Glad you got it worked out. What threw me was it started but when your son removed his hand it died. Did you replace the solenoid or modify it?

@meintsgwen

2 жыл бұрын

Modified it. Put a shut off valve in gas line and removed rubber ring from solenoid

@JOEZEP54

2 жыл бұрын

@@meintsgwen The shut off valve is a good idea even if you put in a new solenoid. I add them to all of my units. Keep in touch & stay well, Joe Z

My brother-in-law has a Bolens riding lawn mower that is super loud and he had a brand new muffler put on it. Is it a gasket or what? Sounds like a helicopter. He uses it and he has to cover his ears with ear covering to mow with it. I may not know exactly what part you're talking about - too bad we can't use pictures.

@JOEZEP54

Жыл бұрын

If if is a head gasket it would be lacking power & if you remove the dipstick while it is running you will get oil splashing from the oil tube the stick was pulled from. Stay safe, Joe Z

@icemancometh8679

Жыл бұрын

@JOEZEP54 Someone said it could be the gasket by the muffler or a loose spark plug. I just know it sounds like a Harley - real loud!

@JOEZEP54

Жыл бұрын

@@icemancometh8679 Start with what is the easiest for you & track it down. You will find it..

@icemancometh8679

Жыл бұрын

@JOEZEP54 It's funny he won't let me near it unless he's there. I think it's because he wants all the credit for fixing it. But could be because he don't want me to break it, ha ha. So next time I get a chance I'll look at it. Bolts that need tightened down maybe - but which ones?

@JOEZEP54

Жыл бұрын

@@icemancometh8679 Not sure where to direct you. Did you change a head gasket before?

Came for the mower stayed for the accent no homo

@JOEZEP54

3 жыл бұрын

Francisco Curiel, Thank You for watching hope this was of help. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

A bad ignition switch could be the problem since it grounds the coil upon turning the switch off

@JOEZEP54

2 жыл бұрын

Thank you for watching and taking the time to add another cause for this.. Viewers adding useful comments like yours may help other viewers solve their issue. richard t I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Your support is not required or expected but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and using the following links do help. This is always appreciated. Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

Ain't no gas in it.

@JOEZEP54

2 жыл бұрын

Hi Jeff, thank you for stopping by. Although this may seem like a no gas issue, watch this video to the end to see why it would not start. Stay safe, Joe Z

@jessisdad

2 жыл бұрын

@@JOEZEP54 It was a Sling Blade reference.

@JOEZEP54

2 жыл бұрын

@@jessisdad Man I got to get with it LOL

Or. A. Tailim box ba

@JOEZEP54

3 жыл бұрын

Maybe, have to check it out.

@alexbradley7517

2 жыл бұрын

@@JOEZEP54 ain’t no way you deciphered what that guy tried to say

@JOEZEP54

2 жыл бұрын

@@alexbradley7517 🤔

@alexbradley7517

2 жыл бұрын

@@JOEZEP54 lol just teasing with you. phenomenal video by the way it helped me out today

@JOEZEP54

2 жыл бұрын

@@alexbradley7517 Thank you for watching & commenting, glad it helped. Nothing bad poking a little & having a laugh. Hey hope you visit again and be sure to comment. Stay well, Joe Z

Explain kill wire.

@JOEZEP54

2 жыл бұрын

Thank you for stopping by. Are you asking about the kill wire or stating this is the kill wire?

@jennyandrews1671

2 жыл бұрын

What is a kill wire. Been watching about stuff to understand it.

@JOEZEP54

2 жыл бұрын

@@jennyandrews1671 When you turn the key to off, a wire that is connected to the coil shorts/grounds out the current. This will prevent any spark. A wire is also on the safety devices. For instance if you do not step on the brake you will not be able to start. In this case usually it prevents current going to the starter. On push mowers this short/grounded coil happens when you release the bail. Let me know if this is of help. Joe Z

/you took it for granted took it for granted took it for granted took it for granted took it for granted?

@JOEZEP54

3 жыл бұрын

Thank you for stopping by & commenting. I hope this video was of help. If nothing else you have learned " not to take it for granted " LOL I guess I repeated myself a few time here 😟. Hey check out the rest of my channel, you should find some helpful videos and keep me on my toes. Stay safe, Joe Z

It may be a bad carparader. Pistom

@JOEZEP54

3 жыл бұрын

Could be.

Just say diag :D

@JOEZEP54

3 жыл бұрын

Jamie "diag" ?? At the University of Michigan in Ann Arbor, the Diag is a large open space in the middle of the university's Central Campus. Originally known as the Diagonal . LOL Hey thank you for stopping by. Hope this video was of help. Jamie I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Stay safe, Joe Z.

BOHHHSTON

@JOEZEP54

Жыл бұрын

LOL about 4 hours south. Thank you for stopping by. Stay well, Joe Z