Rent this machine at Gap Power. To view specs, prices, or to request reservation, click here: www.gappower.com/Rent-a-Pipe-T...
Жүктеу.....
Пікірлер: 30
@DD19582 жыл бұрын
i think you did a great job on this video.
@michaelcooney76874 жыл бұрын
Fantastic vid... Used one today.... completely baffled me but had enough "bush" experience to get the job done...🤓🤔😉😎
@brianjackson38857 жыл бұрын
i learned how to do this almost 20 yr ago workint at the hardware store
@joseluisverasegovia80792 жыл бұрын
Excelente
@cynz42992 жыл бұрын
3:50 threading starts
@khalidtauhid53672 жыл бұрын
You should use hand glove brother
@mdmomen7185 жыл бұрын
Nice 👍💖💖
@Mjknapp227 жыл бұрын
The 914 diehead is only used for British BSPT & BSPP threads. Your video actually shows the 714 diehead used for NPT threads. Also, at the 6:36 mark you should point out that for straight threads NPSM the release foot & sine bar have to be set according to steps 2 & 3 on the die head setup chart. You have them set properly but didn't instruct to do so. Otherwise great video!
@GapPowerRental
7 жыл бұрын
Hi Michael, great critique of the video, you know what you are talking about. You are correct, it is a 714 die head being used for NPT and NPSM, not the 914 - function is exactly the same for the sake of instruction on this video. Thanks for pointing that out. We do start out the segment at the 5:30 mark on straight threads mentioning that we are now illustrating straight threads but do not specifically mention that they are NPSM, which they are. I usually reference pages 10-12 on the 1224 Threader User manual for instructions on the 714 die head. You can find the manual here: goo.gl/wgsQvH
@adidevkids6587
4 жыл бұрын
Uae price how much
@adidevkids6587
4 жыл бұрын
Dai
@ringodingo6 жыл бұрын
7:30 remember to ream the pipe end before threading it. : )
@jeffreyrichardson
4 жыл бұрын
wrong
@brandonmurphy4657
4 жыл бұрын
Actually that's right . Cut team then thread
@brandonmurphy4657
4 жыл бұрын
*ream
@juninhotedlogam Жыл бұрын
Bacana demais
@lakshmannair36823 жыл бұрын
Can use this mechine for to thread stainles steel pipe
@samwalls4253
3 жыл бұрын
Yes
@mkgaming30392 жыл бұрын
Havtu bai
@user-un9ui6te8y2 жыл бұрын
ماهو الزيت المستخدم والمخصص للتبريد
@gunaseelan7891 Жыл бұрын
how to procure these machine spares in Tamilnadu ? any supplier is there?
@JhonnyDegracia6 ай бұрын
Como roscar tubo de 1pulgadaun cuarto
@candyman57493 жыл бұрын
The video isn't much of a help. I need to figure out why the machine is producing screwed up threads. The die is somewhat new, but it produced chewed up threads half of the time, and won't thread unless constant pressure is kept on the die, for some unknown reason. The machine is very old.
@user-cf2iq1lc8w3 жыл бұрын
Bangladesh delivery sistem
@francisleblanc32162 жыл бұрын
en
@jeffreyrichardson4 жыл бұрын
theodore bosse sharons donna camossee lauries cup of tea
@greenhunter523 жыл бұрын
how about teach people the proper way to use these tools by wearing gloves and protecting your fingers from infection due to the cutting oil and sharp edges. Also the wheeler x 6790, oils through the die head, has been a much more versatile and maintenanceable machine that I've used in house for over 20 years. Your technician used bare fingers to pull metal shavings out of the pipe...
@candyman5749
3 жыл бұрын
Its probably not wise to wear gloves around rotating equipment.
@Zacharyr222
2 жыл бұрын
OSHA forbids wearing gloves on rotating equipment so you don’t rip your arm off because a little cut is better than a missing arm.
Пікірлер: 30
i think you did a great job on this video.
Fantastic vid... Used one today.... completely baffled me but had enough "bush" experience to get the job done...🤓🤔😉😎
i learned how to do this almost 20 yr ago workint at the hardware store
Excelente
3:50 threading starts
You should use hand glove brother
Nice 👍💖💖
The 914 diehead is only used for British BSPT & BSPP threads. Your video actually shows the 714 diehead used for NPT threads. Also, at the 6:36 mark you should point out that for straight threads NPSM the release foot & sine bar have to be set according to steps 2 & 3 on the die head setup chart. You have them set properly but didn't instruct to do so. Otherwise great video!
@GapPowerRental
7 жыл бұрын
Hi Michael, great critique of the video, you know what you are talking about. You are correct, it is a 714 die head being used for NPT and NPSM, not the 914 - function is exactly the same for the sake of instruction on this video. Thanks for pointing that out. We do start out the segment at the 5:30 mark on straight threads mentioning that we are now illustrating straight threads but do not specifically mention that they are NPSM, which they are. I usually reference pages 10-12 on the 1224 Threader User manual for instructions on the 714 die head. You can find the manual here: goo.gl/wgsQvH
@adidevkids6587
4 жыл бұрын
Uae price how much
@adidevkids6587
4 жыл бұрын
Dai
7:30 remember to ream the pipe end before threading it. : )
@jeffreyrichardson
4 жыл бұрын
wrong
@brandonmurphy4657
4 жыл бұрын
Actually that's right . Cut team then thread
@brandonmurphy4657
4 жыл бұрын
*ream
Bacana demais
Can use this mechine for to thread stainles steel pipe
@samwalls4253
3 жыл бұрын
Yes
Havtu bai
ماهو الزيت المستخدم والمخصص للتبريد
how to procure these machine spares in Tamilnadu ? any supplier is there?
Como roscar tubo de 1pulgadaun cuarto
The video isn't much of a help. I need to figure out why the machine is producing screwed up threads. The die is somewhat new, but it produced chewed up threads half of the time, and won't thread unless constant pressure is kept on the die, for some unknown reason. The machine is very old.
Bangladesh delivery sistem
en
theodore bosse sharons donna camossee lauries cup of tea
how about teach people the proper way to use these tools by wearing gloves and protecting your fingers from infection due to the cutting oil and sharp edges. Also the wheeler x 6790, oils through the die head, has been a much more versatile and maintenanceable machine that I've used in house for over 20 years. Your technician used bare fingers to pull metal shavings out of the pipe...
@candyman5749
3 жыл бұрын
Its probably not wise to wear gloves around rotating equipment.
@Zacharyr222
2 жыл бұрын
OSHA forbids wearing gloves on rotating equipment so you don’t rip your arm off because a little cut is better than a missing arm.