RFID Programming Guide
** EDIT **
Managed to find a copy of the instructions and uploaded here. Enjoy!!
www.yorkshireautomation.co.uk/...
This is a short video describing how to programme the RFID keypads in preparation for inclusion in a Z-Wave system. Visit www.yorkshireautomation.co.uk or just email me info@yorkshireautomation.co.uk for more information.
If you enjoy watching these videos then please show your appreciation by making a small donation:
www.paypal.com/paypalme/yorks...
Many Thanks
Пікірлер: 164
Thank you for taking the time to make and share this. There's a funny, benign background to this story, but the short version is that with this video and a Cyrillic instruction manual I now control access to a 20+ apartment building in Eastern Europe.
Thanks to share this information. Great job!!!! Once again thankssssssss
Great video. Thanks
Great job .. thanks ...
Excellent
I added a new RFID Keyless Tags with the same frequency so both old and new tags are working. I was able to open the door using those tags but it never goes back to lock mode itself. It usually goes to lock mode after a few seconds. Instead I have to de-energize the unit so it will lock again. Also, adding a tag number 2 doesn't work I used the number "5" instead. We have the same RFID Controller but I don't know why the difference. Your feedback is highly appreciated. Thanks!!!
@YorkshireAutomation
3 жыл бұрын
Thanks for your message. I have posted the instruction manual in the description. Best is to read that. I'm not an expert in these keypad but was demonstrating how to integrate with fibaro in that video. Unfortunately I don't know the advanced details for this device. Only thing I can suggest re lock issue is to check the 'auto lock' time settings
THERE IS SOME GOOD INFORMATION IN THIS VIDEO - HOWEVER IF YOU TOOK SOME TIME TO EDIT THE GAPS - WHEN YOUR TRYING TO THINK OF SOME INFO, IT WOULD MAKE THE VIDEO MORE EFFECTIvE. THANK YOU FOR THE VIDEO EITHER WAY :D
@BrytonLifts
4 жыл бұрын
Chill
Hellped Heaps thanks Ross NZ
Hello... I want to know something about this device... Can we attach electric gate lock with this?
@YorkshireAutomation
4 жыл бұрын
Yes
Hi. Anyone know how can I buy the replacement sticker for this model?
Anyone that uses this RFID system shown is asking to have whatever it protects access to, accessed, you might as well put a key under a plant pot. All the control on the back, easily accessible to anyone who levers it off the wall.
@YorkshireAutomation
5 жыл бұрын
Not quite. The keypad in my scenario is designed for indoor use. Unless you know which wires to short out you won't disarm the alarm. This video is only to demo the turning on/off of an alarm system and not door entry system.
@randyclark583
2 жыл бұрын
Qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq
Could you tell us some more about what power source you are using?
@YorkshireAutomation
6 жыл бұрын
Robin Kaiser I am using this keypad as a home automation alarm keypad. So I have a basic 12v 2A power supply
@robinkaiser3252
6 жыл бұрын
Thanks m8 :)
Hello, please could you tell me how to change the time between door unlock and lock, because I have an equal device, but its time is 1 minute, it is a long time waiting for the door to lock again, and the LED is red again. thank you very much
@YorkshireAutomation
7 жыл бұрын
hi. according to manual i have this is what you do: '*' then 'your password for config' then '#' then '3' then '2 numbers for your new time eg 10 for 10 secs' then '#' then '*' to finish. this would change your unlock to lock time to 10 secs. hope this helps
We have this unit and everything works great. However, when I purchased extra FOBS, they can't be programmed! How can I ensure I am getting the correct FOBS when I order additional ones? As it turned out, the new ones are larger, but thinner than the original ones that came with the unit.
@YorkshireAutomation
5 жыл бұрын
Hi, im sorry i dont really know as i use the keyfobs that came with the unit. also i only use this in the z-wave modified version as part of my home security system.
@nazreenbuang3966
2 жыл бұрын
psutisfifsifsifis
Hi, could you help me? When I try and add a tag it continuously beeps. Not sure what I'm doing wrong
@YorkshireAutomation
5 жыл бұрын
Hi I'm sorry I dont know too much about this keypad as I was only modifying for smart home use. I would try and reset the keypad and start again. Failing that get in touch with the manufacturer. Thanks
if mode blink continuously, what is problem?
hello, can yo tell me please, how modify delayed time to open de door, ? thank you.
@YorkshireAutomation
5 жыл бұрын
Hi I'm.sorry I dont have instructions anymore for this model
Did the manufacture code is fungction for all type of acces control?
@YorkshireAutomation
4 жыл бұрын
No. Each panel is different
Hi, i have the same device, but I need the explication in spanish or a user manual in pdf. Would you mind helping me ??
@YorkshireAutomation
4 жыл бұрын
Sorry I don't have pdf anymore
Hello. Can you please tell me, if this device can be used like timed locker? i mean from morning like 7am to 8pm it would be unlocked and from night till morning should be locked. Is it possible? thanks for an answer.
@YorkshireAutomation
6 жыл бұрын
MultiDreamer21 No I'm afraid that this lock doesn't support that.
@MultiDreamer21
6 жыл бұрын
maybe can you tell me which china made device can do this? i mean, i can connect different type of rfid box reader to lock and power cable. i think.
@TheRonDoc
6 жыл бұрын
you can buy a power supply timer used for sprinkles or Christmas lights. they are around $10
@MultiDreamer21
6 жыл бұрын
yeah i was thinking about it, thanks.
@YorkshireAutomation
6 жыл бұрын
Im sorry guys, i only modded this device to use as part of my home automation security keypad. i dont use this for its intended purpose as a door lock and therefore dont know much about that side.
Hi, My AD200-M, does not have a reset button on the board but it has the jumper, Pin1,2,3. to reset it do i have to jump pin 2 &3 and continue following your resetting instructions by powering the device till you hear the bleep?
@YorkshireAutomation
5 жыл бұрын
to be honest im not sure mate
@colinfernandes9552
5 жыл бұрын
@@YorkshireAutomationThanks i found a PDF catalogue online, posted on my previous post
Hi I have a question. What will hapen if the electricity stop. Is the locker automaticly unlocked?
@YorkshireAutomation
6 жыл бұрын
I'm sorry I don't know as I have modified the keypad to use as an alarm keypad in a fibaro home automation setup
@ivozax
6 жыл бұрын
Tnx anyway. HNY!
@StereotypedMe_
6 жыл бұрын
ivozax unfortunately it does :( .. So manual door lock is needed for it. Possibly got another method how to not unlock when no power, dont know how for now..
When hash key is pressed nothing happens what might be the problem
Hi..Brother! Do you have any show about Sebury UReader-D ? Thanks.
@YorkshireAutomation
2 жыл бұрын
I'm sorry I don't
What if you lose the tags?
im install a rfid like that. but when i put the power direct to the power socket. it only beeps, red light only. is that normal??? i hope u can help me. thanks.
@user-gi5tj3yg4g
2 жыл бұрын
The same to me ? Did you find any solution?
Hello, I have same with troubleshooting all light are on when i power ON , light Power ,Ok and modes all toghter ON when i power supply is ON.
@YorkshireAutomation
Жыл бұрын
try reset. otherwise could be an issue with the keypad
Idol pwede din bang nag set up ng card kahit hindi mo na babaguhain ang lock code at system code?
the red light is solid.
@YorkshireAutomation
7 жыл бұрын
in some models the red light is solid. in some it flashes. i have both types. if nothing happens on keypresses then try resetting the keypad. there is a jumper on the circuit board. see instructions on how to reset. failing that contact where you bought from. thanks
You can attach any device with this with the appropriate hardware
How can i convert this device to anti copy device , 😊
I tried a factory reset but now my keyboard is in a constant solid beep and will not stop or reset!! Nothing seems to help even with a power disconnect button reset. Help !!!
@YorkshireAutomation
4 жыл бұрын
Hi If the factory reset doesn't work then that indicates there could be a fault with the keypad.
my red led isn't blinking at power up. subsequently it's not allowing me to program it.
@YorkshireAutomation
7 жыл бұрын
please check the power supply to see if you have power. also could be a faulty keypad
@rafasierra5750
5 жыл бұрын
christopher ayarza me either
can i install one of these on four different doors and use the same pass codes and tags to open doors?
@murtazarafi
3 жыл бұрын
Yes u can
@williamboman8927
3 жыл бұрын
@@murtazarafi can you tell me how to use the same tags with the four controllers
@YorkshireAutomation
3 жыл бұрын
you just add the same tag to all 4 keypads and set the same codes when you are programming the keypad
We are moving into a warehouse that has one of these. I do not know the management code. How do I reset it not knowing the current one so that I can use it?
@YorkshireAutomation
11 ай бұрын
Hi There is a link at the beginning of the description to the manual. That will let you know how to reset it
Is there a way to remotely deactivate a “lost/stole” FOB? Or how can one secure the lock from this rogue FOB?
@YorkshireAutomation
5 жыл бұрын
Hi The only way to remove a fob is to swipe it after entering 'remove fob mode'. If you haven't got the fob then the only other way is to remove all fobs and re add the individual fobs back in.
I recorded the same code for programming and the opening of the door. when I start recording a card I start by entering the programming code. but I always listen to a signal and the door opens and the programming does not start. is there a solution
@YorkshireAutomation
Жыл бұрын
yes, and that is to reset. you cannot have the same codes
hey pls help me fbd-006 access controller user guide give me?
@YorkshireAutomation
5 жыл бұрын
sorry dont know that one
@0:58 standard mode @1:05 bell button / alarm @2:37 factory default / changing admin-code @4:00 register key-fobs to unlock @6:05 register keypad-code to unlock @7:40 delete tags / codes @9:12 FULL RESET @10:16 conclusion
@pastelarianelita9113
3 жыл бұрын
Źz,
@hiukwanpang6622
2 жыл бұрын
Gyghhhhhguuuuuuuuu
@user-tc5jv7uw5d
2 жыл бұрын
How can i turn it off
D0 D1 for what ?
My controller is not giving beeps at all. Please suggest how to activate buzzer
@YorkshireAutomation
5 жыл бұрын
Hi. I'm sorry I don't know how to do that.
hi..if we reset the code, will the tag also be reset?
@YorkshireAutomation
3 жыл бұрын
Yes as it resets the whole thing
how to increase time of opening door ? it is too quick to get lock before someone comes in
@YorkshireAutomation
3 жыл бұрын
Hi Download the manual from the description. It will say in there how to increase. Thanks
Hello i want to ask something in my device i can added 2 card and when i want to add the third one it does not work do you have any information about this could help me please ? Info > the card is working but the device doesn’t allow me to add more than 2 help please):
@YorkshireAutomation
Күн бұрын
@blue7334 it has capacity of the 3rd card is not adding. Try to do a reset and add the cards again. Otherwise you may need to change the key pad
what is this universal sensor you refer to ?
@YorkshireAutomation
2 жыл бұрын
Back in 2016 it was a Universal Binary Sensor. Now they have been superceded by Smart Implant
How about if you wnt to add a new pin password
@YorkshireAutomation
6 жыл бұрын
its in the video mate
What if I had the image of the card in my phone, could i be able to open the door 🚪 using the image of the card on my phone?
@YorkshireAutomation
16 күн бұрын
no. rfid is a radio frequency
@saliaaugustine932
13 күн бұрын
@@YorkshireAutomation Thank you dear
This is the equivalent of using a padlock made if wood instead of metal. Any crook can just shirt out all the cables and open the door
Can u program 2 doors with 2 of these units to share key phobs or is it one phob per unit
@YorkshireAutomation
6 жыл бұрын
hi you can have 1 key fob and program them for 2 different units
I have the same I powered it and it makes a continius sound .How can this stop!
@YorkshireAutomation
2 жыл бұрын
Try and do a factory reset
Assa Abloy aperio mortis wiring diagram
@YorkshireAutomation
7 жыл бұрын
wiring diagram for what please?
My key pad is alarming and can not clear it but can use my passcode to enter but not key fob?
@YorkshireAutomation
Жыл бұрын
It means that the keyfob hasn't been programed in correctly. Need to do again
Hi what do I do if I can’t remember what’s the factory password?
@YorkshireAutomation
3 жыл бұрын
Use the link above in the description to download the manual and factory reset the keypad
Yupt
how to remove the master card assignment I've assigned bunch of master card
@YorkshireAutomation
2 жыл бұрын
You will have to reset I'm afraid
Its not working to my doorlock. The management mode with * and # its not working
@YorkshireAutomation
2 жыл бұрын
Try resetting the keypad. The instructions are on the download link
How to change public open pin ?
@YorkshireAutomation
2 жыл бұрын
in the EDIT section i have posted an image of the instructions that will show you how to change pin
Mine keeps making high pitch sound non stop, anyone know how to fix it?
@user-gi5tj3yg4g
2 жыл бұрын
Mine too ? Do you have any clues!
@nickl.2565
2 жыл бұрын
@@user-gi5tj3yg4g I dont remember what I had done, I think it was something with the connectors inside or turning it off and on again...
Is it for human implants as well
@YorkshireAutomation
5 жыл бұрын
? You can use the fibaro smart implant and still use the same wires
@chetnapatel9700
5 жыл бұрын
Same wires?
@YorkshireAutomation
5 жыл бұрын
Human implants?
@chetnapatel9700
5 жыл бұрын
Yes is it correct to use for human implants as well
What is the model number of this system???
@YorkshireAutomation
4 жыл бұрын
The keypad is a generic keypad, but the home Automation system I use with it is a fibaro system
And how to hack the rfid implant and set new password.
@YorkshireAutomation
5 жыл бұрын
I think I have already shown how to factory reset. Unfortunately I dont have instructions any more for this keypad
How to delete everything to factory settings?
@YorkshireAutomation
Жыл бұрын
there should be a jumper setting or pins which you short out to reset to factory. see link in description for the manual
My pad doesnt have a star button
@hussbarada1
5 жыл бұрын
same here, from outside its there, but when opened to check nothing down the button, is it a malfunction device?any help? email: hussbarada@gmail.com
How to change passwords to open door
@YorkshireAutomation
3 жыл бұрын
take a look at this: www.yorkshireautomation.co.uk/downloads/RFIDmanual.jpg
Waterproof?
@YorkshireAutomation
4 жыл бұрын
No
When i press the star button it does not light green why?
@YorkshireAutomation
3 жыл бұрын
try resetting the keypad. or it could be a faulty keypad
@elias.assaad
3 жыл бұрын
@@YorkshireAutomation done 👍 thank you 😊
Hi, how to change the passcode?
@YorkshireAutomation
2 жыл бұрын
In the description is the link to the instruction manual. Use that to change the passcode
is it possible can you reset just one task?
@YorkshireAutomation
6 жыл бұрын
as far as i know you have to reset the whole keypad. you cannot reset 1 element
HOW MANY TIMES PASSWORD CHANGE IN THIS SYSTEM SIR PLS TELL ME🙏
@ahmermohammad2556
Жыл бұрын
You can change the password as many times as you like. I don't believe there is a limit
Can you just delete 1 tag and not all
@YorkshireAutomation
5 жыл бұрын
From memory I believe you can. I will need to check. I'm away at the moment and will update when I get back next week.
@colinfernandes9552
5 жыл бұрын
@@YorkshireAutomation To delete individual cards watch this video kzread.info/dash/bejne/pKZopc-iZcTKYMo.html
Where is J2?
my door lock opens automatically after power supply goes off and on. Can you help me please?
@YorkshireAutomation
3 жыл бұрын
Download the manual from the link in the description to change the parameter settings
@replay.gaming
3 жыл бұрын
@@YorkshireAutomation Not able to find. Can you help me please?
@YorkshireAutomation
3 жыл бұрын
@@replay.gaming www.yorkshireautomation.co.uk/downloads/RFIDmanual.jpg
@replay.gaming
3 жыл бұрын
Thank you for the pdf. I switches to NC port but now the gate is just opposite. When i enter passcode it closes and after 5 sec it opens. Do i need to change any other wires?
@YorkshireAutomation
3 жыл бұрын
@@replay.gaming I think a change in wiring is required for that
Only Legends use RFiD access control for Safety. Saya dah pernah install dekat toilet. Puas hati member nak pakai kena bayar rm1.