Thank you for taking your time on the taillight you are a blessing

I live in a country where Cadillacs aren't available and I have never even laid eyes on an XLR before but I still found this video fascinating. Good job.

Fantastic video! Thanks for sharing and saving people thousands.

This was an awesome video! Watched almost all of your tuning videos and i thoroughly enjoy the passion you exude through them. I dont own any chevys i just genuinely enjoy the content and want to learn to tune! keep up the great work!

Thanks for the video I got my led for $12 eBay and my brakes works great thank to this great video 🤙🏼

Why did I watch this video? Never buying an XLR but it was very interesting - great work!

I don't have an XLR but know about the rear light issues, love this video, great job! Hats off!

@GoatRopeGarage

2 жыл бұрын

Thanks! 👍

@jackdaniels2657

Жыл бұрын

@@GoatRopeGarage is it possible to program the XLR ecu as an e40 I got a Gen 3 lsx engine md I wanted to see if it's possible to use XLR ecu on my Gen 3 swap

Great tutorial, Thank you!!!

Just curious... in the video you said 5mm led.... the link you posted is 3mm..... jus checkin before I order and thank you for showing how to do it

great vid.thanks

My driver side outer strip went completely out. I see a little moisture condensation on the inside lens. I’m assuming it’s the control board inside because it happened suddenly in the rainy humid weather here in Florida. Im good at electronic repairs it’s the separation of the lens and housing that has me nervous. Would you recommend the heat gun or oven technique now that you have done the repair. That’s the only part that I question on what’s best without damage. I have a heat gun already.

I have an 06 that has no lights in just one column of the passenger side light. The other column in that light functions well. Would that be the controller? Are there 2 controllers per tail light, one for one column of lights and another for the other column?

I have an ‘08 XLR that the turn signal lens on the passenger side head light came off. Any advice on a repair?

Hey do can you fix these and how much?Only left tell light out , brake lights still work.

Interesting video. I have two questions... Who gave you the instructions of 220 temp for the "Oven Method"? and Why do your hands shake so bad?

Any substitutions for the Permatex black rubber sealant. That seems to be out of stock or no longer produced.

I decided to restore my 05....my tail light has been repaired BUT it got moisture in it after the repair and now the whole thing only lights up when the alarm sets....even then it's weak. I suspect it's the pwr supply/control board thing. I don't mind attempting to do it myself but I worry that the sealant used from the led repair will make it a bad challenge.

What year srx should I ask for on ebay, we have a 05 xlr

Nice video I watched it three times and read all the comments. I've decided it's worth paying $500 to have a professional repair and refurbish the entire lamp with warranty. Besides If I break it trying to fix the lamp, my list of : broke things while trying to fix would become even longer.

@GoatRopeGarage

3 жыл бұрын

Nothing wrong with that, if it showed you how in depth it was and helped with the decision is still doing it's job!

@Dafs193

3 жыл бұрын

@@GoatRopeGarage Thanks for the info. I just bought one off facebook marketplace for $450, it looks great but has one strip completely out. Also noted by my wife it has water trapped inside. Hope the repair place in California doesn't reject the lamp due to water inside. My original lamp works completely but has cracks on the lens. Wife said swap the lens, but risk of breakage is doubled.

@Dafs193

3 жыл бұрын

And also thanks again for the terrific video keep up the great work.

@Dafs193

3 жыл бұрын

Well I did it, got the lens cover off using a small hair dryer, a plastic pry tool and patience. It was full of water that's why it was flickering. Dry it out, hook it up to the car and bingo everything worked, no soldering needed. Thanks again for the most excellent video.

link on ebay to buy the 100 pcs bag thing?

In the Video you stated that you were using the 5MM LED replacement bulbs, but the link is for the 3MM bulbs - which should be ordered? Thankyou so much!

@briandoty229

2 жыл бұрын

following.

Thank you for the video, please text me the name of the glue you used. Thanks again.

Great video! What heat gun do you recommend?

@GoatRopeGarage

2 жыл бұрын

Any heat gun will work, heck a hair dryer might work for splitting them, just be careful with a heat gun as it can warp the lens.

Did you make a video on how to take the third brake light out?

@GoatRopeGarage

Жыл бұрын

I bought a new one, they were still cheap, not sure now

Where are you located?

I just bought one of these cars and was suprised at how expensive the taillights are. My LEDs are out in the white section of the lights. Is it the same bulb, expect for being white?

@GoatRopeGarage

3 жыл бұрын

Think they are all the same, the reds are just behind a lens

Is it 5mm or 3mm? U said 5mm in video but linked 3mm ??

Question: My left tail light has dim/flickering parking lights, but the turn signal and brake light works fine. Is that the controller?

@GoatRopeGarage

3 жыл бұрын

Most likely

just make sure you people are aware. When you replace one or two leds and not all of them, in a few weeks or months others will start going out .that is why people that do them for a living replace all the leds and the control board with a NEW ones. This is a good patch job if you have an old beater and just want to get by and don't mind a warped lens or possibly breaking it. if you have what looks like cracks on the top area that you can see you will most likely have many pieces when you take it apart .at best the cracks will open up enough to leak moisture into the light

@GoatRopeGarage

4 жыл бұрын

How much do you charge for the service, Mike?

@mikeripley3266

4 жыл бұрын

@@GoatRopeGarage I don't do them. I have been sending them all to one guy who gets 400. he has done about 25 over the last 4-5 years . replaces all the leds wit ha later upgrade found on the 2015 and up cars. never has a failure. I am really watching the tune video. I have a belt supercharger I have all lined up on one of mine. I can make it fit , I just cannot make it run.

So...I paid some guy I found on the XLR forum....he scratched the top of my light and I overlooked it.....the first rain I had.....there was condensate forming in the light....could never reach the guy again so fast forward a couple of years.....I let the car sit and decided I'm going to drive the car......nope...lights not working now. My question is.....I don't know what the guy used to glue it back together.....do you think heat will still open it up?

Hey question for you! I have a 2016 xlr v where the passenger side light doesn't light up at all. Does that mean I have to buy a 2010-2016 srx taillight an steal the control board out of it? Thank you.

@GoatRopeGarage

4 жыл бұрын

Yep! But they are pretty cheap

@ryandecker2693

4 жыл бұрын

@@GoatRopeGarage yeah was just looking. I guess you could by one that just has some leds burnt out or do you recommend like a new one.

@GoatRopeGarage

4 жыл бұрын

@@ryandecker2693 I'd get a cheap one, couple LEDs burned out are just bad LEDs

@ryandecker2693

4 жыл бұрын

@@GoatRopeGarage yeah that's what I was thinking. Does it matter if you get a passenger side or driver side.

@GoatRopeGarage

4 жыл бұрын

Hmm, that's a good question and I don't know the answer, I'd probably try and get the side that's burned out to be safe

Yeah you referred to them as a tremor, was curious myself. If this is an inappropriate question, please disregard.

@GoatRopeGarage

4 жыл бұрын

Not at all! I have essential tremors, had then since I was about 12, nervous system thing, kind of like Parkinson's, but they are an at rest tremor where as essential tremors are a motion tremor that show up when you're trying to do something. Can barely solder anymore because of them but it's one of those things where the medicine to help is as bad as just dealing with them. It's much less debilitating than Parkinson's and usually gets to a point of severity and levels out, mine haven't gotten much worse in the last decade. Mine predominately appear through my hands and my vocal cords.

@jdoe880

3 жыл бұрын

@@GoatRopeGarage Great video TY. In regards to your tremors, have you seen any of the treatment that uses the deep brain stimulator?

@garyblomstrom1556

3 жыл бұрын

@@GoatRopeGarage I don't suppose you're in a cannabis legal state? Anecdotal results are mixed but some successes are incredible.

@GoatRopeGarage

3 жыл бұрын

Not an option

I have a buddy that has one of those Cadillacs and he bought HP tuners and then he found out they don't support his vehicle he was unable to tune his vehicle how are you tuning yours?

@GoatRopeGarage

4 жыл бұрын

Holley Terminator X and a PCS transmission controller

@mannyr.2756

4 жыл бұрын

@@GoatRopeGarage thank you for the reply, Okay so how did you get your instrument cluster to work and things of that nature reason why I'm asking is because I have a 2010 Camaro originally a 6-cylinder car I threw in a 5.7 and a 4 L70 transmission and of course my cluster didn't operate among other things so I had to reinstall the factory PCM that way it will communicate with all the other modules in the car that way my dash for instance where work how did you overcome that?

You said 5mm but the link shows 3mm?

Hey dude thanks for sharing I had no idea those lenses at that expensive that is crazy, and are you okay what's with the shaking hands?

Anyone else have issues with the drivers side headlight? Our turn signal bulb overhead and melted the yellow cover. All the replacements I've found have the same issue and run between $4-7k. Thanks...

@johngatsby1473

Жыл бұрын

That was supposed to have been remedied by the 2005 year model but mine had it too. Fortunately mine did it while the XLR was still in production and I got it fixed. The best you can do is perform the resistor fix that will at least stop it from melting more or buy some used ones for major money.

It took about three hours to work the lenes off using a heat gun , after that it was a simple process. You must go slow!

hi i have tail light can you reper for me?

What what...I paid 80.00

If you purchased the tail light, why not just use that tail light, why do you have to repair it?

@GoatRopeGarage

3 жыл бұрын

You don't purchase these tail lights, they go for $3k, you can get an SRX taillight for cheap and harvest the controller