Thanks so much! Saved me a lot of headache as I bought the car with the small cap missing on the passenger side, had a replacement cap and did not understand why I can't fit it. This video made me realize I still had the black part of the cap inside the door, and I had to remove it to fit the new part.
@marcus_motors_
2 ай бұрын
It's one of those where you don't know what's in the inside till you take it out haha
@chipbutty4460 Жыл бұрын
Brilliant video, thanks.
@marcus_motors_
Жыл бұрын
Thank you, glad it helped. Did you change for standard or paint them?
@girbilmusic3446 Жыл бұрын
Precise work, can you make a video for the other side and back doors as well?
@marcus_motors_
Жыл бұрын
I'm painting the replacement at the moment where the old one snapped, I'll do a short clip at the end of the video showing how to do it but it's practically identical 👍
@goldytwatus1674 Жыл бұрын
Very nice, definitely an improvement on the chrome
@marcus_motors_
Жыл бұрын
Yes definitely imo, the chrome look is very dated now
@sogi5559 ай бұрын
Hey, I was able to uninstall the driver side handle, but on the passenger side I don't have a screw behind the rubber. I tried to pry the "cap" part of the handle from outside, no luck, no clue how to move on. Any tips? Many thanks!
@marcus_motors_
9 ай бұрын
Hi, not saying you wouldn't have thought to check with a torch 😂 but is there definitely no screw? If there's not I'd try giving it a push to knock the barrel out of its seat, as I did in the video after I unscrewed it. But then you run the risk of the barrel being loose once you've pushed it out of its seat and not having a screw to hold it back together again. You're welcome to send me a video on Instagram if that doesn't work
@sogi555
9 ай бұрын
@@marcus_motors_The barrel was fixed with some kind of silicone / glue, I guess something fishy happened by the previous owner, that's why I didn't have a screw either... I applied a little bit more force than the "comfortable" amount and it finally popped out. Too bad the void of the door swallowed one of my bithead in the process... I'm going to try to fish it out somehow later. Many thanks for your help and for your videos!
@marcus_motors_
9 ай бұрын
Ahhh right, didn't think it sounded right that it was still being held in position. Wouldn't know where to look for a spare but at least you know silicone would be enough. Maybe a magnet on the inside of the door and slide it back up the hole? Thanks mate, see hoe you get on
@blueyesITA Жыл бұрын
Hello, on the passenger side is ok, but on the driver side I cannot pull out the cover with the key hole,is there any tip?
@marcus_motors_
Жыл бұрын
Hi mate, did you give the bolt a little tap back in once you wound it out? That loosens the barrel
@blueyesITA
Жыл бұрын
@@marcus_motors_ what do you mean exactly? screwing it back a bit or beating it?
@marcus_motors_
Жыл бұрын
Don't like knock fuck out of it 😂 just push it back in with out screwing it. Watch from 1:00 and you can see I don't push very hard at like 1:10 mark 👍
@blueyesITA
Жыл бұрын
@@marcus_motors_ yes "beating" was not the right word I guess 😀, anyway it worked perfectly! It came out with no effort in this way and did all the job in 5 mins. Thank you again! Best video on YT, other guys broke some parts in this process in their video and that did not make me comfortable at all.
@marcus_motors_
Жыл бұрын
Haha surprising hoe tight it feels until you give it a little tap! Thank you. The little tabs do break like I showed on my passenger, but for the price and how quick it is to sort, its not a big problem. Thanks again for the comment man, appreciate it
@AS50uk Жыл бұрын
Hi can you show us how to remove/replace center wheel hub caps please also what mm I'd need
@marcus_motors_
Жыл бұрын
Just the badges in the centre? When I changed mine, I pierced the badge with a hook tool and just pulled them out. Rather than mark your alloy by going in at the edge.
@AS50uk
Жыл бұрын
@Marcus Motors I'm not sure what size I'd need is it 60mm? I have a 2016 Giulietta. It's the same process - they have a sticky back?
@marcus_motors_
Жыл бұрын
I completely missed that bit 😂 I had 60mm, I've got the standard turbines, haven't seen a difference between specs. Be safe and measure them. No not sticky back, you want the one with white plastic tabs, not the metal rings
@AS50uk
Жыл бұрын
@Marcus Motors oh in that case I think I'll leave it as I have no idea what I'm doing haha. Thanks for the help appreciate it.
@marcus_motors_
Жыл бұрын
If you don't want to ruin the old ones for whatever reason you could take the wheel off. But I've never needed the cap off for anything other than changing them, so the easiest way is just break them apart staying away from the actually wheel and pop the new ones in.
@christopherhall3645 Жыл бұрын
Stupid question time because I can see, but to be sure... Door card doesn't need removing?
@marcus_motors_
Жыл бұрын
Nah mate don't need to touch anything on the inside of the door, just the screw along the side, then the rest from the outside
@christopherhall3645
Жыл бұрын
@@marcus_motors_ Hero. Thank you. Even for driver's side no door card off?
@marcus_motors_
Жыл бұрын
Yeah exact same mate. I did a clip of thw driver sides at the end of the plastic painting video because someone had asked me to show them fitting it
@christopherhall3645
Жыл бұрын
@@marcus_motors_ will watch now. Thanks so much.
@marcus_motors_
Жыл бұрын
Let me know you get on. The only difference is the cap and barrel are separate 👍
@renemorales23615 ай бұрын
Same for alfa romeo 159??
@marcus_motors_
5 ай бұрын
I don't think so mate. Same principles might apply, as in access from the spine of the door but I can't help with that one mate
@malandro26 Жыл бұрын
Sounds so good, looks easy, but it's not: by holding the torx screw to maintain the inner part of the handle in position, the whole part can falls down into the door. Besides, it's easy to loose it inside the door when you're trying to put the handle. I had to replace a broken handle due to an assault and this video tutorial only presents the "happy path"... I recommend to leave the car in a workshop.
@marcus_motors_
Жыл бұрын
That assault probably broke something making it hard work for you. The job can't be any easier
@KingAndaval11 ай бұрын
I followed this (to replace a broken handle) and the bloody screw thing fell down in to the door 🥲
@marcus_motors_
11 ай бұрын
You animal! 😂 I've done it a few times and would struggle to wind mine out. Magnet wrapped in a cloth and drag it back up to the hole?
@KingAndaval
11 ай бұрын
@@marcus_motors_ It’s gone right in to the bottom corner, no change of getting it, I don’t think. I’ve managed to secure it with a screw right in to the plastic where the barrel would otherwise be… will probably just 3D print a replacement. Took the door card off and tried to spy it through the opening for the window clip but no joy. Guess the only way would be to drill out the rivets behind the door card and then reattach but not worth the effort haha. Thanks for the video though - would never have attempted this myself, otherwise! Most importantly I was able to fix the broken handle for no cost by gluing it :-)
@marcus_motors_
11 ай бұрын
If I had a 3d printer, I don't think I'd be drilling out the rivets for that 😂 feel like I did more damage than good on this one 😂
Пікірлер: 46
Thanks so much! Saved me a lot of headache as I bought the car with the small cap missing on the passenger side, had a replacement cap and did not understand why I can't fit it. This video made me realize I still had the black part of the cap inside the door, and I had to remove it to fit the new part.
@marcus_motors_
2 ай бұрын
It's one of those where you don't know what's in the inside till you take it out haha
Brilliant video, thanks.
@marcus_motors_
Жыл бұрын
Thank you, glad it helped. Did you change for standard or paint them?
Precise work, can you make a video for the other side and back doors as well?
@marcus_motors_
Жыл бұрын
I'm painting the replacement at the moment where the old one snapped, I'll do a short clip at the end of the video showing how to do it but it's practically identical 👍
Very nice, definitely an improvement on the chrome
@marcus_motors_
Жыл бұрын
Yes definitely imo, the chrome look is very dated now
Hey, I was able to uninstall the driver side handle, but on the passenger side I don't have a screw behind the rubber. I tried to pry the "cap" part of the handle from outside, no luck, no clue how to move on. Any tips? Many thanks!
@marcus_motors_
9 ай бұрын
Hi, not saying you wouldn't have thought to check with a torch 😂 but is there definitely no screw? If there's not I'd try giving it a push to knock the barrel out of its seat, as I did in the video after I unscrewed it. But then you run the risk of the barrel being loose once you've pushed it out of its seat and not having a screw to hold it back together again. You're welcome to send me a video on Instagram if that doesn't work
@sogi555
9 ай бұрын
@@marcus_motors_The barrel was fixed with some kind of silicone / glue, I guess something fishy happened by the previous owner, that's why I didn't have a screw either... I applied a little bit more force than the "comfortable" amount and it finally popped out. Too bad the void of the door swallowed one of my bithead in the process... I'm going to try to fish it out somehow later. Many thanks for your help and for your videos!
@marcus_motors_
9 ай бұрын
Ahhh right, didn't think it sounded right that it was still being held in position. Wouldn't know where to look for a spare but at least you know silicone would be enough. Maybe a magnet on the inside of the door and slide it back up the hole? Thanks mate, see hoe you get on
Hello, on the passenger side is ok, but on the driver side I cannot pull out the cover with the key hole,is there any tip?
@marcus_motors_
Жыл бұрын
Hi mate, did you give the bolt a little tap back in once you wound it out? That loosens the barrel
@blueyesITA
Жыл бұрын
@@marcus_motors_ what do you mean exactly? screwing it back a bit or beating it?
@marcus_motors_
Жыл бұрын
Don't like knock fuck out of it 😂 just push it back in with out screwing it. Watch from 1:00 and you can see I don't push very hard at like 1:10 mark 👍
@blueyesITA
Жыл бұрын
@@marcus_motors_ yes "beating" was not the right word I guess 😀, anyway it worked perfectly! It came out with no effort in this way and did all the job in 5 mins. Thank you again! Best video on YT, other guys broke some parts in this process in their video and that did not make me comfortable at all.
@marcus_motors_
Жыл бұрын
Haha surprising hoe tight it feels until you give it a little tap! Thank you. The little tabs do break like I showed on my passenger, but for the price and how quick it is to sort, its not a big problem. Thanks again for the comment man, appreciate it
Hi can you show us how to remove/replace center wheel hub caps please also what mm I'd need
@marcus_motors_
Жыл бұрын
Just the badges in the centre? When I changed mine, I pierced the badge with a hook tool and just pulled them out. Rather than mark your alloy by going in at the edge.
@AS50uk
Жыл бұрын
@Marcus Motors I'm not sure what size I'd need is it 60mm? I have a 2016 Giulietta. It's the same process - they have a sticky back?
@marcus_motors_
Жыл бұрын
I completely missed that bit 😂 I had 60mm, I've got the standard turbines, haven't seen a difference between specs. Be safe and measure them. No not sticky back, you want the one with white plastic tabs, not the metal rings
@AS50uk
Жыл бұрын
@Marcus Motors oh in that case I think I'll leave it as I have no idea what I'm doing haha. Thanks for the help appreciate it.
@marcus_motors_
Жыл бұрын
If you don't want to ruin the old ones for whatever reason you could take the wheel off. But I've never needed the cap off for anything other than changing them, so the easiest way is just break them apart staying away from the actually wheel and pop the new ones in.
Stupid question time because I can see, but to be sure... Door card doesn't need removing?
@marcus_motors_
Жыл бұрын
Nah mate don't need to touch anything on the inside of the door, just the screw along the side, then the rest from the outside
@christopherhall3645
Жыл бұрын
@@marcus_motors_ Hero. Thank you. Even for driver's side no door card off?
@marcus_motors_
Жыл бұрын
Yeah exact same mate. I did a clip of thw driver sides at the end of the plastic painting video because someone had asked me to show them fitting it
@christopherhall3645
Жыл бұрын
@@marcus_motors_ will watch now. Thanks so much.
@marcus_motors_
Жыл бұрын
Let me know you get on. The only difference is the cap and barrel are separate 👍
Same for alfa romeo 159??
@marcus_motors_
5 ай бұрын
I don't think so mate. Same principles might apply, as in access from the spine of the door but I can't help with that one mate
Sounds so good, looks easy, but it's not: by holding the torx screw to maintain the inner part of the handle in position, the whole part can falls down into the door. Besides, it's easy to loose it inside the door when you're trying to put the handle. I had to replace a broken handle due to an assault and this video tutorial only presents the "happy path"... I recommend to leave the car in a workshop.
@marcus_motors_
Жыл бұрын
That assault probably broke something making it hard work for you. The job can't be any easier
I followed this (to replace a broken handle) and the bloody screw thing fell down in to the door 🥲
@marcus_motors_
11 ай бұрын
You animal! 😂 I've done it a few times and would struggle to wind mine out. Magnet wrapped in a cloth and drag it back up to the hole?
@KingAndaval
11 ай бұрын
@@marcus_motors_ It’s gone right in to the bottom corner, no change of getting it, I don’t think. I’ve managed to secure it with a screw right in to the plastic where the barrel would otherwise be… will probably just 3D print a replacement. Took the door card off and tried to spy it through the opening for the window clip but no joy. Guess the only way would be to drill out the rivets behind the door card and then reattach but not worth the effort haha. Thanks for the video though - would never have attempted this myself, otherwise! Most importantly I was able to fix the broken handle for no cost by gluing it :-)
@marcus_motors_
11 ай бұрын
If I had a 3d printer, I don't think I'd be drilling out the rivets for that 😂 feel like I did more damage than good on this one 😂