Great explanation only thing I find weird in any of these videos is the 1/8” everyone states but it’s more like 1/2” to 3/4” of play

Best video yet on the subject!

Best Video you guys have explaining this subject!

Clear instructions, I like this. Always wondered if I had everything set up correctly, now I know. Thanks

Great video!! I’ve been running Rekluse for years with several different bikes and still didn’t understand how it all tied together. Thank you for simplifying it!

I've only got two rides on a Rekluse on my CR500 but it has been awesome. No longer fear hitting the rear brake too hard and can concentrate on turning rather than managing the clutch in ruts.

Excellent explanation. Thank you!

Excellent video that helped me resolve an issue I was having with my Radius CX which was dragging. Ended up moving increasing the set gap and swapped out the springs to the all Silver springs. Works perfect now.

Thanks for doing this video. Clear, concise and gives the best explanation yet.

Good clear explanation. I figured there was something wrong with mine as when it's hot it feels like the engine is hunting but it's the rekluse pulsing. I don't like it but at least I know what it is now 😃

Great video but your idea of an 1/8 inch is wrong. When you adjusted it to where you said it wasn't enough gain you were close to an 1/8 inch. Where you said it was correct it was probably around a half inch.

Is the inner clutch on a z start pro suppose to sit flush inside the basket? And when I say flush I’m saying or asking does the inner clutch sit all the way back on the inner basket. I’m having a problem where it sticks out from the basket just a little bit and I’m not able to get any clearance between the top most friction plate and the pressure plate causing the clutch to not disengage.

My bike pulls me forward while just sitting on it to the point where you can't start or stop it gear without stalling. So I probably just need heavier springs and adjust free play.

All these videos is on dirtbikes I wish you would on my yamaha yfz450r

I have the Core EXP 3.0 installed on my 2013 KTM 350 XC-F. After setting the free play (1/8 in) and with 3 red and 3 blue springs, it is still pulling when in gear. RPM is around ~2200. Tried lowering the RPM, but still drag. Should I upgrade to all 6 blue springs? Any advice or tipes would be appreciated.

@RekluseMotorSports

2 жыл бұрын

Hello, thanks for your question. For assistance, could you please send your question to customerservice@rekluse.com, and a technical associate will help you out. You can also reach us at (208) 426-0659 8AM - 5PM MST.

How long (hours of use) will the clutch plates work before being replaced? Any signs of when it would be time to put in new clutch plates?

@RekluseMotorSports

3 жыл бұрын

Thanks for your question. The exact interval for clutch maintenance will vary based on several factors such as riding style and conditions. Here is a link where you can find more information on when it's time to perform clutch maintenance for auto clutches; however, many of the same concepts carry over to our manual clutches. If you have any questions, please contact customerservice@rekluse.com or give us a call at (208) 426-0659. blog.rekluse.com/how-to-properly-maintain-your-rekluse-auto-clutch

We see alot of how to set up FPG, but what about how the clutch should behave when we pull the lever in? I am having issues getting the clutch to disengage when I pull the lever in. I have to pull it almost all the way to the bar for full disengagement. It's risky when riding.

@RekluseMotorSports

2 жыл бұрын

Hi Kristina, thank you for the reply and using our products. Can you please give our customer service team a call @ 208-426-0659? We want to make sure we get you taken care of. Our team is here Mon- Fri 8-5pm Mtn. time. Thank you so much!

Do you have to use the clutch lever to shift gears with the Rekluse radius cx clutch?

@dill5500

Ай бұрын

You don’t have to do that on any dirtbike

I think I have an odd presentation. It appears that I have more free play gain (lever moves more than the 1/8-1/4") but with bike on stand and put in first gear the wheel is turning fast with loads of drag. Even if I pull the clutch in the rear wheel is hauling and I cant hold it with my hand to stop it.

@bboydawgy

3 жыл бұрын

Adjust your free play gain to the correct amount first. If you put any bike with a rekluse on a stand with the properly set FPG, the rear wheel will spin. As long as it’s not pulling you away with the wheel on the ground, you have the correct amount of FPG

Ciao mi chiedevo se la fatto anche x 250 2t yz ,, e come dove la posso comprare

What is free play gain is good. Dosnt "walk away" but bucks just a tiny bit. But it very hard to find neutral now. Is this a common issue? I've got a 2020 yfz450r with rekluse radius cx.

@tron121

2 жыл бұрын

My 06 YZ bucks in gear clutch out also. No problems with neutral though. i've not tried to solve it, the behavior changes with trans temps too. Mostly i just put it in neutral or pull the clutch if its annoying, in gear and riding is perfect though.

Why no one is talking about down shift (engine breaking) with rekluses clutch, is this a secret until you have to buy one?

i have about 1/4 inch of freeplay gain but bike still stalls when stoping in 1st gear. also it chatters/shutters went getting moving from a stop.

@RekluseMotorSports

11 ай бұрын

Hello throttlefilms, thank you for reaching out. Can you please contact our Technical Support team at 208-426-0659, Mon-Fri 8-5pm MTN. They can also be reached at customerservice@rekluse.com. They will be able to get you taken care of. Thank you!

I wish you would do this on a yamaha yfz450r qaud

@RekluseMotorSports

2 жыл бұрын

Thank you for your interest in this video for your YFZ450R. We take customer feedback into consideration when prioritizing new videos. The function of auto clutches and auto clutch drag for ATVs will be similar to dirt bikes. If you have any questions about your setup, please give us a call at (208) 426-0659 8AM - 5PM MST, or send us an e-mail at tech@rekluse.com.

Saya dari Indonesia berapa dana yang di butuhkan untuk jadi otomatis pada Yamaha yz250f tahun 2013

Looks more like an inch of movement. Where is the measurement done? End of the lever?

I had one on my 1090R for only 8000 km...most of which was a big trip to Yukon and about 500k of more hard core offroad (KTM rally in Vernon, BC). Near the end of me using it, the clutch would stick "on" meaning I could not pull the clutch in to disengage it. Caused a few crashed on the trails. No one could give me an answer as to how this was happening. I was sent some new teflon pads but that made no difference. Had to remove it and now it sits in a box...a huge waste of money. Any input as to how to solve this issue would be appreciated.

@RekluseMotorSports

Жыл бұрын

Hi Derek, Thank you for reaching out and commenting. We would love to dive in and get you help. Could you please shoot us an email to customerservice@rekluse.com. Our team will be more than happy to get you taken care of. Have a great night!

need video on how to adjust free play gain on a yamaha without the slave...internal adjustment....where is that video?

@RekluseMotorSports

2 жыл бұрын

We appreciate your input. We don't currently have a video for this subject, but the instructions can be found in your clutch installation manual here: rekluse.com/support/

@thepatternforms859

2 жыл бұрын

@@RekluseMotorSports thanks! Get that video created ASAP. They help the stupid people like myself who can’t read worth a damn :)

Does anyone know where I can get a new throw out washer from the radious x kit? My engine guy lost it lol

@RekluseMotorSports

Жыл бұрын

Hello Nick, thank you for your comment and running our products. Please contact our customer service department at 208-426-0659 Mon-Fri 8-5pm MTN. You can also shoot us an email at customerservice@rekluse.com. They will get you taken care of. Thank you.

@G1bson258

Жыл бұрын

@@RekluseMotorSports I have sent y’all three emails lol never got an answer on any of them and I’ve called too, that’s why I came here to see if y’all would reply. Did find the washer on there tho and ordered it

ha, the auto clutch gets drag... man i cant stand auto clutch on dirt bikes!

Dreadful clutch system and design.

@RekluseMotorSports

Жыл бұрын

Hello Blake, thank you for watching our video and leaving a comment. We would love to get additional feedback on our clutch system. Could you please shoot our customer service team an email at customerservice@rekluse.com. Have a great day!

@Skizm_admin

Жыл бұрын

@@RekluseMotorSports you don’t reply to emails, you’ve tried this “thanks for watching bull crap” on 2 previous comments and you don’t ever reply to the emails I send.