Regenerate the tattered plane with outstanding sharpness
Тәжірибелік нұсқаулар және стиль
Thank you for watching.
This time, I got an old canna with tattered and rusty rust, so I took a total of 50 hours to repair it until it could be used.
Personally, I like videos that play old tools, so I tried it for the first time to try it myself.
As expected, it was used by professionals, and I am very satisfied with the finish and sharpness.
When I examined the paper (an old leaflet of Higeta Shoyu) that was sandwiched between the plane blade and the plane in the video, I found that it was the leaflet used around the 1970s.
We are very grateful to Higeta Shoyu for the direct confirmation and the very polite response from the person in charge.
I was deeply moved when I learned that the plane was used before I was born.
I would like to continue uploading videos related to woodworking, so please subscribe and rate if you like.
#plane
#Restoration
#repair
#Woodworking
#Rust
Пікірлер: 28
色々参考になりました 私も倉庫の奥にねむる古い道具を治して使おうと思います 素晴らしい動画でした♪
@KITUNEBI-ch
Жыл бұрын
ご視聴ありがとうございます そう言って頂けると嬉しいです！
12:24 切れ過ぎw気持ち良い👌
鉋かける時は、刃ではなく台を持つと良いですよ。 台は平らでも削れないので、台直しする事もお勧めします！
@KITUNEBI-ch
Жыл бұрын
ご視聴ありがとうございます😊 裏金の調整や台直しは一応しましたが、動画がとても長くなってしまったのでカットしてしまいました。 最後辺り、駆け足な動画構成になって申し訳ないです、、
Good sprit, good work. Congraturations！
I think you might want to add thickness on the bottom of the plane, the mouth of the Dai is quite wide now
@KITUNEBI-ch
10 ай бұрын
Thank you for watching. Thank you for the wonderful advice 😊 I will use it as a reference.
カンナをよみがえらせるよりカンナのつかえる家を作らせて欲しい！そう思うのは私だけ！
なんか、海外の方の動画を見ているようでした。w
@KITUNEBI-ch
2 жыл бұрын
ご視聴ありがとうございます🦊 海外のrestoration動画を見るのが好きなので、真似をして作ってみましたw 楽しんで頂けたなら嬉しいです😃
木 すりかわってる 継ぎはぎの材料は どこに
@KITUNEBI-ch
10 ай бұрын
ご視聴ありがとうございます^ ^ 木 すりかわっていませんよー
Practical
最近大工道具を触り始めた者です。 #3000の時なぜ最初少し引いていたのですか？
@KITUNEBI-ch
Жыл бұрын
ご視聴ありがとうございます😊 3000番の仕上げ用砥石の時少し引いていたのは、刃先（鋼の部分）を鋭く整える様に引いて研いでいました。 正確な角度と、刃先の鋭ささえ出せれば抜群の切れ味になりますよ^ ^
@Gqze
Жыл бұрын
@@KITUNEBI-ch 次回からやってみます！ありがとうございます😭
PLease, next time you do one of these do not use abrasive brushes or chemicals to remove the rust, convert that rust into ferro ferric oxide (BLUING) by boiling all of those items in water. This restores some of the oxidised steel into bluing which can hold oil and prevent further rusting. grinding off or etching off the rust means you LOSE all that protective potential.
@KITUNEBI-ch
5 ай бұрын
Thank you for watching. Thank you for the wonderful advice and comments. I'll try something like that next time.
@markmanning2921
4 ай бұрын
@@KITUNEBI-ch I learned this by watching all of Mark Novak's videos here on youtube, he is probably the best gunsmith in the entire united states and he is very articulate and has a good way of explaining things. rust bluing is how the old timers would blue guns, they would do something to make them rust then boil them in water.
初めましてこんにちは。 鉋の刃机の上等に置く時は鎬が下になるように(刃先と机等が接触しないように)置く方が良いですよ◎ 台治し、裏馴染み等も治すと更に良くなると思います🙏
نعرف الضرب فوق مش المؤجرة
@KITUNEBI-ch
Жыл бұрын
Hello Thank you for watching
@ibrhemahmed170
Жыл бұрын
@@KITUNEBI-ch thanks
Can I propose to you a recipe to remove dust? Bicarbonate of sodium plus white vinegar.
@KITUNEBI-ch
Жыл бұрын
Thank you for watching. I remove dust and dirt with a surfactant. Rust is removed with a rust remover, but recently I've been using strong citric acid.
最後のカンナかけでエッとおもいました。