I had this problem with an AVR 1804 receiver. This video was the first I came across when searching for an explanation and a fix. Although the detail and layout of the internals are different to the AVR488 shown here, the cause and solution are the same. I replaced the two 15V regulators which are attached to the heatsink. Receiver works fine. Most of the time was spent dismantling the unit in order to get the main board out. Thanks for posting this fix on KZread.

@databits

7 жыл бұрын

Hey! Glad the fix worked for you on a different model.

DB: So far, so good, after holding in the two speaker buttons while concurrently holding in the power button. Who knew? You. Thanks for sharing. I've had this piece for some time and got it from a guy who looked like he wanted to take an ax to it - kind of like the out-of-shape guy who rids himself of the row machine because it reminds him he never used it. For that reason while picking up furniture from him for my wife, I offered him $20. Faces' "Long Player" is just that as we move into side two on this Thanksgiving weekend Sunday. Thank you, sir.

Great video! I have an AVR-588 that had the same problem, but switching the power regulators didn't fix it. So now it's a doorstop. I'll do some more research next time I shop for a receiver... Denon is out for me.

Even though this is an awfully old video, it helped me fix my receiver. I didn't think about factory resetting it, d'oh. Thanks!

@databits

4 жыл бұрын

YAY! Glad it worked for you.

Thank you sir, you just make my day. My denvor avr-1603 had standby problem which is fixed by your tips.

@MikaelStalhammar

11 ай бұрын

I have the "red light blinking" issue with my AVR-1603 as well. Do you mean you replaced parts in yours to fix it? Which parts? Or did you just do the reset?

Thanks for your comment Michael about the Denon receiver. I totally agree. Yamaha or Pioneer would be my next choice.

I had a Denon AVR-1707 and the man who bought it from me told me it happened to the receiver. I'm telling him about this vídeo. Thanks.

Thank you very much sir....I just pressed the power button and held it for about 5 seconds and it seemed to reset. Time will tell but A BIG THANKS TO YOUR VIDEO, YOU TUBE, THE INTERNET! I must have music or my life is not the same. Thanks again to you for helping me.

@databits

5 жыл бұрын

Thanks for your comments!

@Buick_the_rd.master

4 ай бұрын

Thank you!!! I was so disappointed I hadda go out tomorrow on my day off and buy all these supplies to fix my stereo. But your power button trick WORKED!!!

Thanks for this - I have (4) of these units, of which (3) doing the same protect thing. They were all thrown out for this reason, so hope the fix is as simple as this! Thanks!

@databits

7 жыл бұрын

Did it fix it?

@robydany8749

5 жыл бұрын

No update

Awesome info. I was about to junk my receiver, did the reset and it work Thanks.

I tried the “holding down buttons reset” option. The glitched looking screen didn’t pop up like it did in this guys video.. thought it didn’t work. But it came to life! - I have my receiver in the same room at 2 fish tanks. So I have 3 lamps, 2 aquarium air pumps, 4 aquarium lights, 2 filter systems, and more. So I’m drawing a lot of power.. so this is why I believe it went into stand by mode, to many things was plugged into the power box it’s hooked up too

Thank you . It works . Demon AVR 1312.Thanks for your video . I just resets it to factory settings.

Hey thank you for sharing your finds, it is a very informative video..

I've ordered the parts to fix my Denon AVR-588 as a result of this video. I'll be posting a comment next week to let you know how I make out.

@londonpinball

8 жыл бұрын

+London Pinball No go. Replaced the two regulators and it did not solve the problem. This receiver may hit the river soon. The research continues...

@DarkerEmpathy

8 жыл бұрын

+London Pinball Thankyou for updating us with your results! :) (I have the same issue)

@londonpinball

8 жыл бұрын

+Zoloft, Montreal I never solved the problem and instead tossed the unit from a very tall building. No more problem!

@eman59461

6 жыл бұрын

Some times the output transistors go bad it can cause this too. I repaired a few with this problem

@eman59461

6 жыл бұрын

u can test them with a meter if u get volts in not out that your bad chip.

I have the same receiver and the reset worked on the 5th try. Thanks

My power "halo" would not even light up. I pushed the three buttons and it fired right up. Thanks so much!!

totally worked mine was not turning on the red light would come on and after clicking the button to turn it on it wouldn't so thank you totally worked

Thanks for the video very helpful. I have the avr-488 also. Just replaced both the parts on the heat sink and it didn’t fix the problem. Wondering if the second heat sink part needs to be replaced or the capacitors. No issues with the fuse either.

Good job. I've posted a number of repair videos and repair the stuff for a living. One thing i worry about is people attempting this stuff who really have no business doing so. We both should probably warn people more severely. There's really a potential for a lot of trouble with unknowledgeable people attempting this stuff.

@404010ful

2 жыл бұрын

that's what I said in my comment I would take it in if my issue didn't solve .

Thanks!! I powered off my Denon AVR, held both speaker buttons down and turned it back on. I found out that by default the volume is turned completely off. As soon as I turned up the volume I heard music. Thanks, that's a great unit and I'm really glad to have it working again!!

@databits

7 жыл бұрын

Glad this helped!

Hi, I have the same model like your and have same issue, I will try this and hopefully it will help, Thank you for the video.

Thanks now I am going to connect mine to my kenwood power amp..so it will not cause too much stress on the amp itself.

Great video. I got my AVR 941 from the dump, so, back it goes. I can't do all the above because I have fat hands. Time to buy MORE audio equipment.... yaaaaay !!!

Hey thanks for sharing. I have a 589 and it’s doing the same thing. Just replaced the 7815 transistor and the two capacitors. Didn’t fix it. I noticed the two transistors you pointed at are on the side of the head sink. Mine has those two plus two on the ends of the heat sink. So now I gotta pull the CB out again and tackle those two transistors. Question though. How does that other CB unplug. I tried for ages to get the two sockets to release and I could not get them separated. As you,know it’s impossible to get the transistors off with the other CB in the way. I don’t want to pull too hard in case I break something. Cheers

Because I have the electrical soldering skills of a moose I shall try the reset option only ! If that fails its in the trash. Great video by the way . I agree with the other guys comments what type of person leaves a thumbs down ????

My AVR-5800 just went out today. Went into protect mode. Already have in the shop. It is indeed a beast and I don't want no new one!

@ahsanafzal48

6 жыл бұрын

Jay G. What did they say the problem was n is it fixed and how

@gosman949

6 жыл бұрын

I paid $300 and a capacitor was shot on one channel. And oddly the other channels had loose capacitors too. I heard on one youtube site that these receivers had poor solder joints. Well after 17 years, I guess my solder joints cracked! But I'm a up and running now blowing the house down!

@ahsanafzal48

6 жыл бұрын

Jay G. Hood job. I am from london and bought one from a guy near my house. I bought a marantz sr6008 av. I saw it working at his house. When i brought it back to my house.. it turns on then off after few seconds. Seller wouldn't provide refund. I dont make much money and can't afford to get it fixed. Hate my life

@gosman949

6 жыл бұрын

Probably a capacitor or resistor came loose from a solder joint in transport. Easy fix if you can find someone that works on electronics. I'd recommend my man but he is in Dallas! Sorry to hear this but save your pounds, you can fix someday!

@ahsanafzal48

6 жыл бұрын

Jay G. Thanks jay.. you are a good man 👍🙄

Great Video. Unfortunately, the repair did not work on my AVR-588 (I see I'm the second one who was unsuccessful attempting this repair on this model.) What a PoS.

I have a different year. An little older, but my Denon is flashing red without any LED screen. I was listen to my reciever a little to loud and a burnt smell and smoke came from it. I need to get it fixed, I noticed there is a fuse blow in the back where you were pointing about to much soder. But great video.

I like the vid. Could you direct me to the blog that you referenced? I have a Denon 689 which has been shutting off for a couple of years now. I put a fan on top of it blowing down into it and that remedied it for quite a while. Now it is shutting off more frequent. I got a bigger fan, which helped, but with it being summer it's out of control. I took mine apart, removing the boards. Mine's a bit different with 2 large heat syncs and 3 regulators on each. (Yours has one large and one smaller heat sync) One of them is the 15 volt 7915 regulator. Just wondering if that's the one that needs replacing. That's why I wanted the blog you referred to in case there was any additional hints there. Thanks

you fixted it thanx

I love there power supplys in there . Mine had the same issue its the 7200 WA model from 2014 to 15 it came out with the W and there was a HDMI board upgrade a year later so I bought the A version . Mine kept shutting off with blinking standby If I raised the vol it went off. I checked all my connections did notice I wasn't getting enough output from my surrounds L and R aparantly the terminals were touching the metal stand I moved it away and the output is normal. the AVR has not shut off I lthink it was protecting itself. So good video . A guy like me would take it in I thought a fuse was going .

nice work sir, gotta learn a lot from you

So I think I overheated mine and this is happening now. It’s blinking red and when I press Power it shuts down after a few seconds. Think there’s any hope in it being on after it cools down?

Thanks!

I have Pioneer VSX921, suddenly notices there is not audio from SBR and SR channel; I checked that there is audio at relay PIN. Other channels are working fine. could it be a problem with relay? any logic that is not turning relay on. Thanks in advance

Yep, the reset tip works on my Denon I rescued from the tip. Using a different set of buttons labelled surround located in the same spot. Thanks mate!

I it worked on a two channel model with only a reset thanks for sharing

You are amazing

Does this work for AVC-1800, with the same 'Red Blinking'? And what are the two buttons you press to reset it?

@vincentdelacruz8001

7 жыл бұрын

Tom Elliott ... I have an 1801i recently picked up @ a thrift store for $ 14.99 . I reset mine using ( after going friggin nuts with all the buttons and videos), by pressing...Memory+ Mode+Power...At the same time,but release the power button 1st, when it changes on screen, release the mode/ memory buttons...mine says "Auto Preset"..blinks a few times then says ,"Completed". Check it out if you haven't figured it out yet. Peace...

THANK YOU!

Hiw do you do a factory reset on a demon AVR -4800 just forget how to do the factory reset on this unit any help would be appreciated

Reference my last comment. I held down the buttons and tried to reset several times . On the last attempt there was a loud popping noise and a small puff of black smoke. It safe to assume the thing is toast .

Hi, do you k ow how to fix the same problem for harman kardon AVR-151. Power indicator keep blinking or goes off can't start up.

Do you think this would work for a AVR-688?

my denon avr-2105 was playing music through my speakers then it made a loud crack and smoke came out of the top and it then went into standby then u turned it back on and there was a even bigger bang and way more smoke now when i turn it on it just shuts off again. I don't know what to do.

hi iam an engineer thanks that advice was correct thank you. ihave had alot of denon for repairs 1 star dont like it. this unit is good when they work when they dont bin job thanks.

Great. It worked. Thanks.

@databits

9 жыл бұрын

Francisco Goitia - Glad it worked for you!

I have an AVR-487 and I have the same issue. However, my circuit board looks a little different and I’m not sure where the transistors are that need to be replaced. Any suggestions?

Hey did you notice any corrosion after you took off the voltage regulators? I replaced the two and it didn't work but there is a third I see on a different aluminum heat exchange on the same circuit panel that also seems to have corrosion. I will replace that and hopefully that will do the trick

@databits

10 жыл бұрын

I don't recall seeing any corrosion, just some black or brown discoloration on the circuit board.

Databits, Are you in StL still? What would you charge to do this repair? Thanks!

@databits

9 жыл бұрын

probsn - Yes, I am in St. Louis - can you message me?

u just clutched thank u

thank you

Thank you so much...

Thanks for the guide. I'd attempted this repair and two times I witnessed the new capacitor blowing. Not sure where to go from here and am thinking a new amp is in my future.

@databits

9 жыл бұрын

Bill Flemming Good idea!

@ralphbonser736

9 жыл бұрын

Bill Flemming Hi; If you are referring to the electrolytic capacitor(s) on the voltage regulator inputs, I would check them to make sure they have greater than 35 volt working voltage rating (marked on side of electrolytic capacitors), and for reverse installation. The tricky one is the electrolytic capacitor connected to the minus (-) 15 volt (7915) regulator. On this one, the positive (+) side goes to ground, and the minus (-) side goes to the regulator input (pin #2). This is how a polarized electrolytic capacitor is connected for negative voltages. Good luck.

@ralphbonser736

9 жыл бұрын

Ralph Bonser Not sure why part of the text has a strikethrough. It is applicable. Thanks.

Thank you.

Hail, fellow St. Louisan! Ok, I have a AVR-1604 I have located the heat sinks and the Capacitors that may fix it I have not attempted this yet. I ordered the Caps but you mention some kind of "washers" do those go between the caps and the board I assume? Again I have not taken anything off I wanted to buy all the parts I need before moving forward.

My denon avr-s510bt has a similar problem. It keeps shutting off if the volume was too high. I put it on eco mode and turned the volume way up which caused the unit smoke. Something was smoking at least.

I have an older integrated amp that banks on startup for maybe 2 secs then turns solid and is fine. Is this normal.

hi came across your video after searching for possible solutions. I have this same problem only I also know why. I am renovating and living in a semi building site. I had the misfortune of having a speaker fall from a shelf above while trying to fix an unrelated network issue. The speaker cable came loose and fell onto the chassis of my Denon AVR 4310 and shorted something out. Given the cause is likely or possible the solution will be the same or similar or is the damage likely to be more severe?

@trustnoone3795

5 жыл бұрын

I don't know. Having been a consumer electronic repair tech. 40 or so years, when you have a foreign object fall into an uncovered, unprotected receiver (or anything for that matter) it can cause almost as much damage as a severe, direct lightning strike, providing it was powered up at the time. Unless you saw where the wire landed & saw anything spark, smoke, etc., it may have caused the same type of chain reaction damage a lightning hit can do. Basically, that means getting ahold of a ''good'' schematic diagram that shows the proper voltages in particular areas or circuits of the receiver so you can take voltage readings (you do have a good volt/ohm meter? I use a digital & analog both when troubleshooting) in areas the wire landed. If yours is completely dead (no blinking light), I'd check all the fuses you can find 1st. You might get lucky, find a blown 1, replace it & you're off & running again. I'd do that before trying to get that schematic. Otherwise, it's ''good'' schematic time. I've got an AVR-1609 that's blinking & I've just let it be for 2 or 3 years until I saw some helpful tips on here. Although I've read a lot of negative comments on here about it being made in China or other things, I really want to fix mine. It was a ''machine''. Not only was the sound quality was excellent, the video circuitry in this thing cleaned & sharpened up the picture on my TV (I still have the old CRT TVs) so much, I couldn't believe it. After having worked on so many ''shut down'' situations over the years, I've learned they're a real pill to work on since nearly any component in any circuit can cause a piece of equipment to go into shut down. I truly wish you all the luck in the world in your repair conquest. Hopefully, a popped fuse will get you going. Again, good luck & take care.

@trustnoone3795

5 жыл бұрын

I don't know. Having been a consumer electronic repair tech. 40 or so years, when you have a foreign object fall into an uncovered, unprotected receiver (or anything for that matter) it can cause almost as much damage as a severe, direct lightning strike, providing it was powered up at the time. Unless you saw where the wire landed & saw anything spark, smoke, etc., it may have caused the same type of chain reaction damage a lightning hit can do. Basically, that means getting ahold of a ''good'' schematic diagram that shows the proper voltages in particular areas or circuits of the receiver so you can take voltage readings (you do have a good volt/ohm meter? I use a digital & analog both when troubleshooting) in areas the wire landed. If yours is completely dead (no blinking light), I'd check all the fuses you can find 1st. You might get lucky, find a blown 1, replace it & you're off & running again. I'd do that before trying to get that schematic. Otherwise, it's ''good'' schematic time. I've got an AVR-1609 that's blinking & I've just let it be for 2 or 3 years until I saw some helpful tips on here. Although I've read a lot of negative comments on here about it being made in China or other things, I really want to fix mine. It was a ''machine''. Not only was the sound quality excellent, the video circuitry in this thing cleaned & sharpened up the picture on my TV (I still have the old CRT TVs) so much, I couldn't believe it. After having worked on so many ''shut down'' situations over the years, I've learned they're a real pill to work on since nearly any component in any circuit can cause a piece of equipment to go into shut down. I truly wish you all the luck in the world in your repair conquest. Hopefully, a popped fuse will get you going. Again, good luck & take care.

I watching this video and start thinking, hey! I can run down to Gateway Electronics and pick up these parts. Low and behold a few seconds later you echoed what I was thinking. Hilarious.

@databits

7 жыл бұрын

You must be in St. Louis?

@moosejaw50

7 жыл бұрын

databits Yes I am. My brother used to shop at Gateway in the 70's. Great place.

@moosejaw50

7 жыл бұрын

I have one of the popular X1200W models that has the blinking light. You have given me a good starting point to troubleshoot the error.

@craigneversleepssleeps2329

3 жыл бұрын

@@databits Same here....I was crushed to hear that Gateway Electronics has closed. :-(

Who the f..k dislikes this kind of video ?

@fx45june

9 жыл бұрын

A demon I mean a denon service tech who wanted to make $200 + dollars for this simple repair . 😂

Using the reset procedure on the Denon X520BT worked as a temporary solution. Will update here if I get to replace the power regulating transistors.

Not sure if your still around.. but I have a denon 3200 and it overloads every time bass hits volume is almost on quiet also

Kenwood AV reciver was giving clicking sound from the poweron relay to supply power to the main transformer. I found that the input to the relay comes from display unit after pressing the standby mode. I checked the input and it was a bit fluctuating which drives a transistor base to give a 12V output to drive the relay coil. The output is fluctuating from 9V to 12.4V. So I replaced the 4.7K ohm resistor with a 3.9K and still it is fluctuating. then I removed the transistor and shorted the collector and emitter which now supplies 12V directly to the relay when power on instead of standby button. The clicking sound went away but the display is flickering. Do you know what should I do.?

kenwood audio/video surround receiver kr x1000 and I am having the same issue but have no clue on what it is..could it be a transistor? It turns on then off and red "CLIP" light comes on and I see no videos on this specific model. Somebody please help

I hope I can fix mine :( thank you for the video. Water got dripped inside while on. Now its on protect. I tried this. Thought it worked. Didnt :( thanks anyway.

I have a Denon AVR 1908 that had the same problem. That repair WORKED. Mine had 6 of the black plastic resistors ordered from Denon$30. PROBLEM now is I have no picture on the TV but I have sound. This is connected via HDMI cable. Anybody have any advise on this repair. Great video btw and thanks, at least I can listen to the radio.

I have a very old AV A1D amp. Moved house. Plugged everything back up and pop. Amp blew out with smoke. Quickly shut it down. unplugged opened up and saw how much circuitry there was inside could not see a blown fuse anywhere. My guess is something got bumped in the move.

at 4:17 you mention the "two power regulating transistors attached to the heat sink." It looks like there are two big one's on the left and x2 smaller ones on the right. Which ones are connected to the heat sink?

@databits

8 жыл бұрын

+anasazi09 - this is explained in the video, there aren't two smaller ones on the right

Do you know why can not work red power indicator in Denon avr-2311? Thanks.

@databits

7 жыл бұрын

I do not, sorry!

YOU'RE WELCOME ticklemebrown52!!

@anthonyslopes3780

4 жыл бұрын

Hey man same problem but avr-3801 don’t look the same. You think you could help me out

great vid. After resetting mine a few times using the speaker a&b+power it would run for about ten seconds and continue to shut off so kept turning it on and off using the standby as you would normally because i was listening for what sounded like a relay killing the power and eventually the problem stopped. Sorry i dont have any clue how many times i did this, also i thought the sound was coming from somehwere near the rectifiers next to the capacitors.

Hallellujah Hallellujah !! This has worked PERFECTLY with my old Kenwood Audio Video Sterep Receiver KR V7060 whoa whoa I cant believe it yet. In a matter of seconds pushing the two buttons as told by DATABITS and Voilá! the Dead is walking again"! Thanks a lot, man, you are a genius!! PD: My middle finger (.i.) goes 2 the writer of the user manual who did not tell nobody nothing about it . "Amplifier Simptoms: the STAND BY indicator blinks and sound is no output. Cause: speaker cords are short circuited Remedy: turn the power off, eliminate the short circuiting , then turn on the power again" YEAH , RIGHT...

Hi. I have a Denon AVR1612 with a similar problem. But the receiver does not turn off. Instead, it restarts several times and will not turn on (start). This only happens if the power conditioner is already connected. If both are off and I turn on the conditioner and then the receiver, the problem does not occur.

havin the same issuew with the AVR s900w...any ideas?

Can you add an arrow or something that point to the two transsistors to be replaced?

@databits

9 жыл бұрын

Francisco Goitia I use my finger in the video to point to the transistors. Best I can do.

Hello everyone, I'm repairing a Denon AVR-1509 amplifier, I can't find the specifications of the D534 diode anywhere, I know it's an AX52 diode, but what kind of diode is it, what specification, what specification? Please help

My advice? Fix your Denon and sell it. Then don't ever buy a Denon again until they start making them in the USA or Japan.

@bombermannbelgium

6 жыл бұрын

Good Idea. .I paid already twice about $800 for a Denon Amplifier, and now the second one is dead too... So, this time it will be a normal cheaper brand...

@diegocanale1124

3 жыл бұрын

Buy Marantz

Hey I have a problem with my AVR-688 where it will run from a varied time range of about 2-12minutes, then it clicks and the red standby light will come on and flash, tried the reset, didn't work, any suggestions? There's also two fuses in it but they look fine.

@databits

10 жыл бұрын

No other suggestions other than what I include in this video. This was my only experience with a Denon. Good luck!

@LarawayS

10 жыл бұрын

Okay thanks.

Denon's quality control has gone way down. It's not rare.

I have had the Ceoln10 for 7 over since months now. This happened to twice already. Not sure why. I just unplugged the power for a few minutes and plugged it back again. I had to do this two times, the red light blinked again after the first unplug, then it worked.

Denon used to be a high quality equipment, I can believe they are doing in china with a chinese low quaity parts

I bought a denon on Craigslist it works but I can’t get my speakers to play out of it Idk how to set it up pleas help

Gateway electric is closed now. I’ll miss seeing Doug!

@databits

Жыл бұрын

Same. It’s so sad.

I’m close to STL myself over in Illinois I’ll pay you to fix my Denon I have the same same model

hello Data bits! how r u ? i have a issue regarding my AV Receiver ,i m also a technician,i have a AV Receiver )DENON AVR-3312 few day back i saw a movie on it it works perfectly next day when i power on the receiver after some time it shuts off and ON automatically and shuts OFF again and again what is the problem kindly guide me where to start the dignose

@ahsanafzal48

6 жыл бұрын

aamir khan start by looking at recycling center

by transistor do you mean capacitor?

Hi Where From I get Circuit diagram ??

How do I unlock the panel on my AVR-1708

That are regulator chips, in a transistor case.

Hi I unplugged my sub and when I plugged it back into a wrong input its blknkin and won't stay but a sec now I thought it was a fuse but thy look OK no broken filament now wen I play it it stays on but low volume.if I try turn it up pow off it goes. I feel dumb cause I paid retail new 599.00 for it and now saw a better model on web for 50 bucks. It was working fine but now I just have sound on thee right speaker and its all plugged up OK. I have 2 Yamaha's for backup rxv model I had an Harmon kardon avr 65 that was aces, an marantz makes some great gar. Model demon DVD player broke to and it was a great sound in DVD 910. Guess I'm done with demon. Hate to throw away but can pay a repai for it. Can get a more powerful modr for 50 bucks . So not worth sinking money into

I did and sold my denon got a new onkyo from hh greg 500 bucks and I can stream music from the internet now .I had a problem with the front panel and sold it

i got a avr 3805 and i got the same problem what can i do😭 havent lisend at music in 6 months soon on it

@foyheathermacdavis6598

3 жыл бұрын

Did you ever get yours fixed? We have the same one with the same issue

@jonasrn1420

3 жыл бұрын

@@foyheathermacdavis6598 u need to go to io do some public and thn go to the drifter

Porqe mi ampli es un denon prende el boton verde pero no prende la pantalla no se qe es si me pueden echar la mano

Check the speaker connections. The protection circuit may have been activated because speaker cable core wires came in contact with each other or a core wire was disconnected from the connector and came in contact with the rear panel of this unit. After unplugging the power cord, take corrective action such as firmly re-twisting the core wire or taking care of the connector, and then reconnect the wire. This fixed the problem for me.

I have a Denon AVR4800 and it is exhibiting the same symptom - shutting down after a few seconds withe the power red light blinking. I tried the hard reset by unplugging and holding down two buttons according to the manual, got the whole screen blinking, but then had the same shutting down problem. Any one out there has the same experience and have been able to recover from it? Thanks.

@tarunsri6023

Жыл бұрын

How did u rectify thn

How normal is the regulator get hot?

Not all Denon avr are bad I have the 1603 after 20 years it's still running

Pretty sure my Denon avr-791 just did this......pounding Elvis-Burnin Love.... Just shut off red light blinking... click goes away click agn comes back on but for for abit then shuts offf after start bumping ... few times in a row now uh ohhh had it for like 3 years

@databits

10 жыл бұрын

Time to purchase a new receiver?

@bcwestcoast3632

10 жыл бұрын

I'm was thinking. .. but now it hasn't done t since so its still bumping on about 3 years strong.. well see thou hopefully doesn't mess up now, knock on wood aha . Cheers

Pay you to fix Mine... St Louis as well AVR 400

@databits

7 жыл бұрын

Okay, but I charge $100. :)