so refreshing to see old school repair rather then just replace

One of the best instruction videos I have seen.

Thank you, really appreciate you taking time to make this video. Feel better knowing how it is supposed to come off and go back to gather.

Thanks a lot - a really helpful video and very well done. I am just rebuilding my tractor water pump and your video is perfectly on target!! George Rutherford in New Zealand

Thank you for a good video that explains how to actually rebuild a water pump. Many other YT videos are fluffed with nonsense about what a pump is or how coolant works. :)

Man, it is great to know how to do this. My water pump on my car just went bad. It costs about 189.00 dlls. This could definitely save me some money. Thank You very much for this video.

Great video and thanks for taking the time & sharing.

Thanks for the info. I knew all that. I just need to know how to get the pulley off without breaking it.

Man. I gotta rebuild my water pump on my excavator John Deere. Sure glad I found this. Thanks.

thanks for your patience many countries of south, america do not manufacture spare parts for vehicles, so we have to repair, thank you for your videos ..

Awesome video Brother! About to do this on my 96 Chevy K1500..Been 12 years since this video,I hope all is well!

Great Job on this video, as you do on all of your videos !

First class video a man that really knows his job

Very informative vid. Thanks!

Cool video, really informative. i think people should overhaul water pumps more often. what would you commend I use to remove a pulley hub for a spin on clutch.

I have your video series and they are great. You do the best job I have seen in explaining what you are doing that I have seen. If you would really get into various repairs on different makes of tractors you would have a tremendous following.

Nice work there

If the impeller or pulley flange of your pump has pulling holes, best plan is to pull them first. Sometimes there’s something hidden behind the pulley that’s important to know before you break the housing! Most water pump housings aren’t all that strong. when you get to pressing and the impeller is stuck, you can crack the housing. Sometimes you have to do it that way, but it’s best to pull impeller if there’s a provision to do it.

Great video! I work on lots of old obsolete stuff. Usually the housing and impellor is fine and all I need to do is replace the bearings and seal. Who is a good supllier of bearings and seals? I'd like to order by dimentions if possible

Thank you for the video👍🏽

Great video

Thank you, sir! You have helped us immensely!

great video, thanks

thank you great video awesome explanation thank you

Nice job. Where can I order seals for my water pump (2004 chevy silverado, 6.0 L. gas engine)?

I have a John Deere 1050 tractor it overheated. It was the first time it is overheated that I know of. I just checked the thermostat and it opened in boiling water. So here's my question. It has a direct fan yamar three cylinder Diesel engine. If I spin the fan fast enough with the top radiator hose off (and the thermostat out) would I be able to identify if the pump is working by the water sucking or shooting out of the top?

Great video, thx My pump shaft broke. What's the best way to get the outer race out?

This is a great vid, but your particular seal style does not contact the impeller shaft as you indicate with a clearance fit, however there are ones that are an interference fit on the shaft and need to be pressed on. The pressed bushing of the seal will turn with the shaft in that design. You should have mentioned the press fit design as well in the video to avoid confusion to the assembler when they go to "slip" the seal over the shaft and it interferes.

Great information. Is that a JD RE41897 excavator water pump?

wow, i actually learned something on youtube!

Good Video ,thanks

Not all bearings get pressed out the pulley side. I did it your way, inside to outside, and the Impeller broke. The pump is an F2244R. On this one, once the pulley is removed, and the hairpin keeper removed, I press the bearing to the inside, and then block the impeller and press the shaft out.

What's a good online source for kits (bearing and seals) for auto water pumps?

Great video. Should help me in rebuilding a Chevrolet truck pump.

this guy is good...

my car has a special water pump that costs over 400$ I found the same pump but not the same cast, the internals are identical, can I simply press the 68$ rebuilt pump's internals out & install them in my old pump?

Where to find bearing and seli kit for waterpump mopar 383, 1967?

How about showing the pulley removal? that IS part of the process!

waw that was a good info

Nice info I'm mechanic auto Can u change water pump move not from crankshaft but into turbines using turbocharger it will increase enggine power also reduce enggine baggages.. and oil pump also Re.. Andy

I missed out on the gasket installation and rebolting

Found this video after I rebuilt my JD pump. I did not put any sealant on the seal housing, now I am worried. I hope it still works........blah.

what is the type of sealant you used for the seal ? who makes it and what is it ? thanks

@123ABC-Machine-Basics

2 жыл бұрын

That is the Permatex Aviation 3D sealer

im gonna be doing this job next weekend does anyone know if you have to pull radiator or can waterpump be removed with radiator still in place thanks

@rgnichols567

3 жыл бұрын

I have an old 5020, & I didn't have to pull the rad. Its tight, but was able to get it out without damaging the rad.

Wrist pin off of what?? lol Nice video

Just wondering how you got the pulley off of the shift? Mine is frozen on pretty solid, might have to get the torch out on this one

@HarveyHamilton

3 жыл бұрын

With a bar type puller.

Can you tell me what this sealant is that you are using on the seal. And also who makes the sealant.

@harveyhamilton9997

Жыл бұрын

The Right Stuff by permatex

I do not order by dimension so I don't have supplier. OEM suppliers many times have kits or aftermarket kits are sometimes available. tiredirontractorparts . com

My Mercedes’ pulley is sticking out 1/4 inch. Can I just smack it back In?

You must be a fellow Pennsylvanian...I heard a "warsher" in there.

The was all pump and no pulley. I want my money back.

but you started after the pulley was of and skipped over pressing the shaft out of the impeller those are the are the things people need help with without it the video is worthless.