Mechanical Seal Repair on a Goulds MCC Series Pump
Chris repairs the mechanical seal (shaft seal) on a Gould's MCC Series transfer pump.
Subscribe & “Ring the Bell”: bit.ly/2CpXSsv
Have a question or need help selecting equipment?
Live chat with us on our website: www.rcworst.com
Call our experts: 855.329.4519
Email: Customer.Service@RCWorst.com
----------------------------------------------------------------------------------------
Our Social Media
Facebook: / rcworst
Instagram: / rcworstcompany
Twitter: / rcworst
LinkedIn: / r-c--worst-&-co--inc-
----------------------------------------------------------------------------------------
We are a distributor of pumps, packaged pumping systems, on-site wastewater treatment equipment, on-site wastewater treatment systems, and custom electrical control panels for water and wastewater applications, water well supplies, drilling supplies, and water treatment equipment.
Пікірлер: 61
My pump was apart for a week or 2 then I ordered the correct parts. Took 3 weeks after that to get a new ceramic shaft seal, spring etc... . Thanks for showing how it all goes together. By the time the parts got here, I forgot.
Thanks, you helped me replace the seal on a much bigger water pump. Never done it before :).
Replacing seals on a 5hp pump tomorrow. Your video helped give me some confidence. KZread University! Thanks!
Great video!
nice tutorial it helps a lot
Thanks young man
Do a no load run on the motor. If it isn’t butter smooth and quiet then you need to be figuring out which bearing is bad. If it is smooth and quiet then put the pump back together. But if the motor has a bad bearing it will ruin the seal fairly quickly.
Hey Chris! Like usual your videos are awesomely terrific! Can you pretty please do a video on how a Venturi (or jet valve located inside the well) of a two pipe well system works? This system uses a jet pump. Inquiring minds want to know. :)
@chrisworst8353
6 жыл бұрын
Robert, I will work on this for you! Great request :)
i have the same issue with Pedrollo water pump ... it starts leaking water and had awful and noisy sound, thnx for the video
@williambrown3388
3 жыл бұрын
I would be looking at the bearings in the motor. If you have a failing bearing in the motor it will cause the seal to fail.
I have a Gould JRS7 and it has a flat head screw instead of a bolt where the propeller is… I am having the hardest time trying to get it off. It’s ridiculous. Any tips for that particular style?
That nut on the impeller is always striped out a spanner wrench works the best just hope the shaft is okay if it's bad it will still leak. the white ceramic It best to silicone the rubber in cheap insurance. lube the seal with soap most likely it for drinking water. when pushed on make sure the seal dose not roll or it will also leak of course keep clean the most common reason it brake like that is from air hammering from a air pocket the impeller being unbalanced/bent wouldn't brake the seal it would have to be bent really bad and if that was the case it would most likely lock the pump end up right away first. Ps. I've been building pumps and booster for way to long it seems like now 17years so I think I done quit a bit of them. for 8 year at least 99 percent of the boosters that have come to our shop have been done by me the only time I have a problem is when the seal is cheap or low quality. I would always pick the highest quality seal if you don't want any leaks. My opinion👍👌✌️💯🥂💦🌊⛲
Good video..👍
@RCworstwater
3 жыл бұрын
Thank you 👍
Put a dial indicator on motor shaft will tell you real quick if it's out.
our J10S does not leak, new impleller, doesn't appear to pump water from one bucket of water to the other bucket of water How to determine why???
Changing a seal but not bearings is like wiping before you poop. The seal doesn’t hold the shaft straight. Time will not tell. You me issue is already clear and should be fixed.
Hey brother, just curious why you didn't show how you removed the front housing from the seal housing...if yours just simply pulled apart, that's awesome. I've never seen the cast iron housing separate easily from the stainless steel housing without using a homemade bearing puller tool. The water is pretty hard and/or corrosive in the high desert where i live and was just curious if you used any technique to separate the housing or not. Thanks, Justin Henry
@RCworstwater
5 жыл бұрын
We had taken it off once before this, and it took us nearly 2 hours. We ended up wrapping chains around it, hoisting it up, and used a forklift to pull down on the chains. It was tough.
@josephsaucedo8691
3 жыл бұрын
It called a hammer give it a good quick smack or use a old screw driver and hit it in between the housing opens every time 👍👌✌️
What is the maximum psi that this type of pump can generate and run at? On a system with a expansion tank.
@RCworstwater
5 жыл бұрын
The flows and pressure capabilities depend on the pump model and HP. Here is a link to the brochure for the Gould's pump MCC series in the video: documentlibrary.xylemappliedwater.com/wp-content/blogs.dir/22/files/2012/07/BMCC-R5.pdf
Very nice and good . I 💕 your video. and you?
I have a Gould J7 that came with my house. I noticed a decrease in pressure and started troubleshooting with your videos and noticed that the motor was set to 230 and there is only 115 that it has been running off of. Is the damage down or would wiring it correctly help to fix the problem?
@RCworstwater
2 жыл бұрын
Only one way to tell - set it to the correct voltage and fire it up!
Why don’t you go with tungsten seals, I work on t-30,t-60, and t-75 rossi and catteli circulation pumps and tungsten material seals seem to work better
@josephsaucedo8691
3 жыл бұрын
That why you use that seal because of hot water and those are perty expensive seals to just put it in because you fill like it. They are a lot better seal though
Hello Where can we find in the Philippines, spare parts for the gould model J5S pump. photo attached. Thanks for your feedback Best regards.
@toptoolclub9780
3 жыл бұрын
Nice 👍🙂
I actually wanted to see the water test
hi buddy ive got a Goulds 1 H.P 2 stage jet pump mounted above ground the well is about 150FT deep im having a hard time finding parts every one wants to sell the whole pump and i have a new motor on it just need to rebuild the pump part leaky seals & o rings ni might as well change the 2 impellers can you help me in any way ? i thank you very much sir .
@RCworstwater
5 жыл бұрын
We sure can! Give us a call at 855.329.4519 or email us at Customer.Service@RCWorst.com. We will need to know the model # of the pump to get you pricing on parts.
@raymondj8768
5 жыл бұрын
YAWZA THANKS A BUNCH THATS OUTSTANDING !!!!
It can be lost the prime because of that seal?
@toptoolclub9780
3 жыл бұрын
I can do see me.
How long do the seals last more or less?
@justinwerner779
Жыл бұрын
Loaded question. Totally depends on run tim, media, lubrication, seal material etc.
You put the seal in backwards, that’s why you got movement.
@frankscarfone7957
4 жыл бұрын
The seal is on correctly. It has to mate against the carbon component
Are there any USA pump Companies left in the USA?
@RCworstwater
5 жыл бұрын
AY McDonald is the preferred water pump brand we sell and install because they are 100% USA made. Check out their products here: www.rcworst.com/A-Y-McDonald-Mfg-Co-c207.html
@lucascoulton
4 жыл бұрын
@@RCworstwater , I just called AY McDonald. They stated only SOME of their pumps are USA made. The rest are imported (Italy and Taiwan were stated). Thought you may want to know that they changed!!!
Preze
Ever hear of an impact wrench?
@RCworstwater
5 жыл бұрын
I think you'll enjoy this video we did on removing a VERY stubborn impeller: kzread.info/dash/bejne/qax82a57kpvKf8Y.html
@robertcerda92
5 жыл бұрын
I would also use another socket to hold the impeller to avoid stripping.
Hi .where can buy a pump parts .?
@RCworstwater
3 жыл бұрын
Give us a call: 855.329.4519
Need illustration to be on the j15s ¬ the j10s they are built differently
Can i work with you
Please help me... I have need to leo Ajm75 pump repair Videos
@toptoolclub9780
3 жыл бұрын
I can bro .
Why did you skip part of the rebuild watched the first video and then you go to this what about the stuff I'm the pump hosing
Hi sir you have mor vdos
Why big box, USPS will choke hold it and body slam it just like the cops if it was in a smaller box!
This video was sponsored by hammer in the background
@RCworstwater
3 жыл бұрын
😂😂
your shaft is bent
Are you chewing gum?