I say hi from Sweden, great video, I follow your channel and like the hole content. Keep up the good work and take care 😀

One area they messed up on was the flashing navigation lights are in the forward direction and the solid white lights are on the outter wing tips. so i plan on swapping the position of those 2 lights on each side

@azzir325

Ай бұрын

Did you figure this out yet? I seem to have lost my flash capability. Not sure what I did but I did get the navs to stay on solid but can't seem to get the things that should flash to do so.

@looneytunes47

Ай бұрын

@@azzir325 Jon from 2 brothers rc shows how to do it in one of his video,s

Thanks for the video, I broke down and bought one even though I really couldn’t afford it yet. Also you gained a subscriber in me 👍

@RCINFORMER

2 ай бұрын

Thanks for buying one thru my link!

Once the rx is installed under the floor you cannot see if you lose bind. To negate this I have placed the rx satellite on the passenger seat. This way you can check that all is OK just be looking at the orange light through the cabin window.

@RCINFORMER

18 күн бұрын

@richardwoods1739 Good Idea!

I missed you man ,im glad to see you again❤👍

@RCINFORMER

2 ай бұрын

Thanks for watching! Been busy at work and prepping the new field! Once we get everything set up, we will be doing more videos from there:)

@Elisrc.

2 ай бұрын

@@RCINFORMER good to hear that👍👍

Just a side note....people sometimes order items based on your review. The dimensions you approximate for the wheels are inaccurate. There is no way the front wheel is that large. In fact, if you remove 3 screws you will find that it is actually a 2" wheel. A 2 1/4" (57mm) will not work. I know because I waited a week only to find out it was wrong. Dubro low bounce 2 1/2" works great with some modification, but no way the dimension for the front works.

@stevehelton3457

Ай бұрын

2 1/2" for the mains. Drexel the pants some and sand down the hub. I also used 2 small washers to center wheel in pants. Tighten all screws and very quiet!

@RCINFORMER

Ай бұрын

I indicated in the video that the nose wheel was approximately 1-7/8".... so I was about 1/8" off, just eyeballing it, when in fact it's really 2".... I indicated that the mains were 2-3/8" to 2-1/2" ...so I was about right on the money by eyeballing it.... I will usually go lower than higher when guesstimating so as not to mislead anyone... my guesstimate numbers were good:)

Did you figure out the lights yet? I seem to have lost my flash capability. Not sure what I did but I did get the navs to stay on solid but can't seem to get the things that should flash to do so.

Lol, they finally found a use for all those VGA connectors since monitors went HDMI

@RCINFORMER

2 ай бұрын

Yep! They are probably getting a deal on them.... but they work well:)

Nice to see finally somebody got this airplane scale proportions right'

@larryblanks6765

Ай бұрын

They had them right when Top Flight built their 182 at the right dimensions, I know I have one!

To bad FMS can't get the stickers straight on the tail like the Cessna and Skylane

Where u at??

Can the tail be removed and put on a new fuse

@RCINFORMER

18 күн бұрын

@@jeffreysmith5825 You should be able to do that as long as there was no damage done to the mounting area.... The tail simply removes with two screws

@jeffreysmith5825

18 күн бұрын

I understand that the tail boom can be removed but dose the tail itself come out​@@RCINFORMER

@jeffreysmith5825

18 күн бұрын

Not sure you answered me

@RCINFORMER

18 күн бұрын

@@jeffreysmith5825 I'm not sure if I understand your question.... Each elevator half comes off and is connected with a spar... Also, the vertical stabilizer comes out as well

@RCINFORMER

18 күн бұрын

@@jeffreysmith5825 None of the tail is glued on.... The vertical stabilizer does go on with a piece of double sided foam tape

Uauuuuuu

Echo makes listening hard 😢

@RCINFORMER

2 ай бұрын

Sorry, we got rid of the echo at about 11min

But what you indicated won't work. Just trying to help others to not waste money and order the wrong wheels.

@RCINFORMER

16 күн бұрын

What did I indicate? My measurements were mostly correct. In fact, I slightly under estimated the size of the wheels so as to not give a falsely larger size. In the future, I will just remove the wheel pant to give a more exact size.... However, this is why I used a ruler in the video....