The knee trick is everything. Thank you again. I didn't have to remove the brake drum. I used a 90 degree allen key with a wrench as extension. It worked flawlessly. Thank you again

I've been struggling for a great while, trying to figure out how to remove the tire. Thank you mate for posting this video.

Wow, I never thought that the drum brake can be removed. I was struggling with that goddamn wheel for two hours, and finally found your video. Thank you, I replaced inner tube in 15 minutes

@jeffs3810

Жыл бұрын

All good, cheers

@krisztinacadwell8602

6 ай бұрын

My son and I are trying to use his technique, but to no avail!! I’m beginning to wonder if maybe in the northern hemisphere it tightens and loosens the opposite direction than it does down under! Just kidding! But really, we’re feeling pretty weak and now our hands are buzzing with the vibration of constantly banging the hammer on the screwdriver. Maybe just a few more whacks will do it. 🤞🏻

Thanks heaps bud, been working on it for hours was about to give up when i saw your video.

this technique works so well it's almost effortless thank you so much for posting

Great video - while you change the tire, also change the tube at same time.... and reverse it so the valve sticks out on the other side - easier to then fit a car pump fitting to pump instead of the stupid little plastic RAZOR extention.

The knee on the tire worked! Thanks buddy

I was convinced that brake drum was pressed on. Had to cut an old Allen wrench to get the wheel bolts loose and was just about to make a tool to remove the ratcheting mechanism on the other side when I figured there must be a better way. Thanks for the vid.

I figured the drum was threaded on! Your vid confirmed it. I plan on changing it to a disk brake. This will make that easier as well. Thanks.

@jeffs3810

4 жыл бұрын

All good ,let me know how the upgrade goes I may do the same , cheers jeff

Mine is stuck and the screw driver and hammer method isn’t working so far, but I will try with some sort of solvent to loosen it up a bit, thanks for the video!

@jeffs3810

Жыл бұрын

Hopefully you got it

@calebm7181

Жыл бұрын

@@jeffs3810 I got it by now, just needed my dad to help me

Tried with a screwdriver and a hammer, but a rubber strap wrench worked really nice for me for getting the drum off the spindle!

Thank you so much you saved my day spent two hours trying to fiddle around with it the other way from some other KZread video watched yours and it was off in 10 minutes

@speedsterh

4 жыл бұрын

Yes, thanks very much for the time saved ! I wish the Razor was designed differently though so you could inflate the inner tube more easily and change the tyre...

@jeffs3810

3 жыл бұрын

@@speedsterh sweet

@adam3842

3 жыл бұрын

I second that! Probably I 16000th that!

I just KNEW somebody had figured out how to remove that brake drum! This screwdriver hammer method worked perfectly. Thanks for the tutorial.

@jeffs3810

3 жыл бұрын

Cool bro

Thanks, Took me longer to get the tube out with the drum in place

@jeffs3810

Жыл бұрын

Yep all good

Hey Jeff, Fantastic how-to video! Thank you so much! Cheers from USA! Duane

@jeffs3810

4 жыл бұрын

Hi Duane your most welcome , stay safe friend , cheers jeff

@jeffs3810

Жыл бұрын

Thanks man

thank u very much ! very clear tutorial here !

Thanks jeff your are the best👍

@jeffs3810

Жыл бұрын

Thanks bro appreciate it

Jeff, thanks so much... I was dreading changing the tire until I saw your video 👍

@jeffs3810

4 жыл бұрын

Most welcome

@jeffs3810

Жыл бұрын

Happy to help

Thanks for your video you solved my problem keep up the good work!

@jeffs3810

Жыл бұрын

Thanks bro

that first step is what put a lot of these things in the trash I bet. I figured it out years ago but wow what a pain to figure it out. Great video!!

@jeffs3810

4 жыл бұрын

Cheers for comments

Thanks to you I was able to change the tube. I have a problem with the tube spinning inside the tire though. The valve stem even gets sucked inside the tire. Everything is tight but I've disassembled and reassembled it twice. Razor sells the whole rear assembly.

@jeffs3810

Жыл бұрын

Ok cool

fantastic help; thanks for producing vid 👍😊👍

@jeffs3810

2 жыл бұрын

Thanks

Thanks for the video

Thanks for the video mate atleast I know what's coming to me waiting for intub tire from ebay and can start working on it

@jeffs3810

4 жыл бұрын

All good mate

Thank you very much. Very helpful.

@jeffs3810

4 жыл бұрын

most welcome cheers

Thank you. I couldn’t figure out how to get it off.

@jeffs3810

4 жыл бұрын

All good cheers

This is great. Thanks so much!

@jeffs3810

4 жыл бұрын

Cheers mate 👍

Cool I went through the trouble but I'll go your way seems pretty easy cheers

@jeffs3810

Жыл бұрын

Thanks bro

Thanks. Our E200 is the same w/ screwheads under the drum rather than on the sprocket side like earlier E200. No room to work an allen-wrench in. It appeared the drum was just pressed on, but now I see it is threaded. Good I didn't try pressing it off. I wondered what the 2 holes were for, to unscrew it with a proper tool like a spanner wrench. Thanks.

@jeffs3810

Жыл бұрын

All good

Wish I would watch this video first!

@jeffs3810

Жыл бұрын

Lol cheers

Thanks...saved me all kinds of time and wasted energy. I owe you a beer sir.

@bjornmartin6480

3 жыл бұрын

Dont know if you guys gives a shit but if you guys are stoned like me atm then you can watch all the new movies on InstaFlixxer. I've been binge watching with my gf for the last few days =)

@seanvance3393

3 жыл бұрын

@Bjorn Martin Yup, I've been using InstaFlixxer for years myself :D

Jeff, I found a Razor E300S setting in a trash can. After getting air in the tire and charging it, it ran fine, except the tire in the rear went flat again. Two things: I didn't know about the extension to inflate the tire and question: can the tube be repaired. I haven't started this project yet, but your video is #1! Waiting for a response in the US! DDK

@jeffs3810

4 жыл бұрын

Hi sure can watch vid on how to remove tire , then fix puncture there might be more than one so submerg in water the iner tube , put on patch then reassemble if you want I will puta vid on puncture repair , good luck let me know how you go

The other side of the rim. The one opposite the sprocket also has a slot for the tube nipple. You can put it that way and then those holes our friend used to bang out the brake drum are for fishing in the air extension adapter through.

Thank you!

Thanks mate!

@jeffs3810

Жыл бұрын

Sweet

Thank you EZPZ

@jeffs3810

Жыл бұрын

All good

My friend thanks so much, im tired take out this boolsheet, your realy halp me!!! Thanks

@jeffs3810

5 жыл бұрын

All good my friends

Thanks!

@jeffs3810

3 жыл бұрын

Cheers bro

@jeffs3810

3 жыл бұрын

Most welcome, cheers jeff

Bang good!

@jeffs3810

Жыл бұрын

Sweet

Jeff is the fcukin Man! Don't you forget it.

@jeffs3810

Жыл бұрын

You are really kind cheers bro

U my man are a fkin legend

Do you know how to get the bearing off?

Hi Jeff, I need your help, if you can help me. I watched your changing the back tire vidio many times, it helped me alot. However, I have a 2012 Razor E325. I took the back tire off, pulled the axel out. It took me a couple days to fix my problem, but I fixed it. My question is, putting the back axal back in, I have 2, spacers, that look like, carbon fiber ? One is about a 1/2" long, and a slight cone shape. The other, in the same material, is like a washer. If I don't put all this back together correctly, it's not going to work. Which spacer, fits where ? Like, does the 1/2" cone shaped spacer, fit on the brake side, or the sprocket side, same with the skinny one. Which side ?

@jeffs3810

Жыл бұрын

Hi bro , look I haven’t pulled a e 325 apart , but I’m going to so I know what you are doing, all I can surgest is you try and search goggle or you tube for a manual that shows a exploded picture of the set up, so sorry I can’t help I’m a single dad with a 16yr old son if I had more cash I would buy all razors and pull them to bits they are really cool bits of kit just need some love to keep them working

Mate! I wish we could video message you to find out what we are still doing wrong. It’s so frustrating that we can’t get this drum brake to loosen after all this banging away with the hammer on the screwdriver. So discouraging!!

Okay so now I need to put the bar back in.. but I don't remember how the nuts and bolts are supposed to go back in. Lol

Been banging this thing mate for 5 mins anticlockwise and it's still seized...any other suggestions?

@jeffs3810

3 жыл бұрын

Maybe put some crc or similar product on it to help free it up , it will eventually undue, cheers jeff

You mention hub comes off clockwise but yet the video shows you removing counter clockwise. Can you verify?

video part 2....how to put air in it.hahahaah!!!!!!!!!! most people never knew how.

What if the first thing doesn't want to come loose?

@jeffs3810

4 жыл бұрын

Hi hit it harder it will loosen cheers jeff

I broke my screwdriver.. now what do I use to open it up? Lol I was hammering on it and it just broke right off from the handle. Lol

If if would of watched the vid. I wouldn't have drilled 2 more screw access holes in the break drum...lol

thetire is already off im trying to take it off

@jeffs3810

4 жыл бұрын

Ok cool what stage are you up to the vid how’s each step , hat are you having trouble with, cheers jeff