This is very cool. I just found my brother in laws E300 that he played with once when he was little. The batteries were completely bloated and it makes a lot of sense to replace it with li-po batteries. I can do everything you describe except except wire the batteries in parallel so I'm very much looking forward to your future videos. You're doing the internet an incredible service. Thank you.

@ebikerich

7 жыл бұрын

Bob Scott thanks. Good luck with your mods if u go ahead

Can someone please give me a link to all the parts needed to get this work

Iam using lipos on my ebike using lipo buzzers what's the best cell voltage to set the alarm at

My e300 always cuts off easily do to hitting bumps but I find that it cuts off to easily and more often how can I turn that option off?

please teach us how to install everything. I need to upgrade my e300. do a tutorial step by step for dummies like me. thanks

@ebikerich

7 жыл бұрын

Ras anal Ghul & The Shadow League yes you can use the key switch in place of the scooter ON switch or have it as well. I didn't use the circuit breaker as it may have tripped with the extra power. Just fit a 30-40A fuse in line with the Lipo positive to the controller. Your controller should have a power input wire coming from the original switch to turn it on, just wire this via the key switch which is built into the throttle assembly. Then wire positive to one side of the key switch, other side of the key switch to the controller. Now the controller won't turn on until the key switch is in the on position.

@mz.l3ul3l3lez8

6 жыл бұрын

Richard Talbot make a video you'll get more subs

@trophix

5 жыл бұрын

Yea please make video... I want to get mine modified.

@TheCaffeineRacer

4 жыл бұрын

Yes that would be great or maybe links to buying the controller etc

quick question, wont adding and extra 24v (48v total) to a 24v motor kill it ??

Hi Richard Talbot I like the build very much, I’m thinking of modifying my e300 would you be able to offer me some advise before I start my project? I would like more power to climb hills I’m not really after speed 15 or 20mph would be ok I already have a 36v 350w controller a 36v throttle and I will get 1 hoverboard battery 36v 4.4ah would this be enough? Should I get a different battery? I am 90kg

"Big motor Razor" by TK is very informative. I watched all of his vids before purchasing 500wt 36v motor,variable speed controllers with voltage readout, new 36v/500wt control module,15T/38T T8F sprockets and chain... inbuilt mine in about 4 hours and it's FAST!!!! Waiting for 10ah Li-Ion battery pack consisting of 18650 Samsung Batteries ( the kind that is used in Tesla Electric Cars)

@Hamid9e

6 жыл бұрын

ragsandrufus how is your experience, has the motor survived from 500w? :-)

@ragsandrufus

6 жыл бұрын

Hamid9e Motor handles all the power that the 500w controller can dish out! Plenty of torque for my 180lb weight but because I wanted more torque I recently installed a 38T rear and a 12T motor sprocket with T8F chain. Now it only goes 16-18 mph top speed Maybe faster If i pointed the scooter downhill LOL

@Hamid9e

6 жыл бұрын

cool, i just installed 500w controller, but the top speed is only 15.5 mph, but great torque! the sprocket is stock. what do i need to change to get more speed?

@ragsandrufus

6 жыл бұрын

Hamid9e i upgraded to T8F chain size and use 11t/38t sprockets The chain will NEVER break now, and she can top at 18 mph

@ragsandrufus

6 жыл бұрын

Hamid9e 10ah + battery capacity in either LiPo or Li-Ion T8F size Chain T8F sprockets... 11T /38T made my Razor go 17-18 on flat... for about 30 minutes

How do I set up a lipo batterys on my e300 im not electrically inclined. Do u know anyone that can make it for me. I have a,speed controller w a,key switch only and qwvot bt 12,ohm batterys. But I need to increase speed by getting lipos and maybe a new sptoket like,a 44 tooth. Let me know if u can help me out. Thanks dovu know were I can buy em and the charger unit and if I need a new controller too. Barry's.

Hello, please help me. I bought an controller and i have 2 wires on throttle called battery + and lock line and i dont where to put them in controller . Thanks In controller i have 2 called lock line and 2 called power display.

Has the motor survived from 800w? 500w then shouldn't be any problem for the motor?

Is there a way to charge without taking out all the batteries?

Please can you link to website products that I will need to give this a go. Exact setup as you have. Thanks

I have the same set up.did you install the sport mode wires,brake wires,and what size fuse are you running? Thanks for sharing this video and information!!

Have you done installation video ? Or can you supply part list

Can you link the parts you purchased please or tell me exact parts

Hi, just got my scooter. Is there any chance you could a video on how exactly you extended the range?

@ebikerich

8 жыл бұрын

I will do a video once I get another scooter to repair. Please subscribe for more up coming videos

@harryfp1494

4 жыл бұрын

Do you use stock break wires or no

burn out the moter very fast?

i took off my brakes and did the controller shunt mod and with fresh SLA, she moves plenty quick. Plus, for the same price, i get 7200 cycles with twice the range, coz its 24V. Best of all, super cheap. Like practically free.

@longcrawler

Жыл бұрын

Not sure I understand what all you did, can you explain better??

I want to make this! Where can I buy everything?

Would like a step by step on wiring it all up.

How do you install the throttle?

Hows the motor? is it going to to over heat?

where did you get the series connectors? How is it doing now almost 4 years later? Is the stock motor still handling the double voltage? any problems? any updates?

@ebikerich

4 жыл бұрын

Made the connectors with some silicon cable and xt60 connectors. Unfortunately I sold the scooter but believe it's still going although the batteries are on their way out now after a few hundred charges. The secret is keep the rider weight down so the motor doesn't get too hot otherwise it wont last!

what battery model are they

I wonder how did u know how to do something like this

Hi Richard, have you any idea what range I would get from 3x3s 5000mah batteries in series (36v)?

@ebikerich

7 жыл бұрын

Danny Walker I should imagine 12+ miles but depends what the rider weighs and hills etc

@dannywalker9288

7 жыл бұрын

Richard Talbot thanks, that's not too bad.

hello there can you make all the connection and no use the circuit breaker? i did connect the new controller and the throttle directly with a 36v battery. the led on throttle lights up but the motor doesnt spin. please help

@ebikerich

7 жыл бұрын

Valerio Altei what voltage is the controller?

@valerioaltei530

7 жыл бұрын

Richard Talbot hey the controller is exactly as the one you have 800w 36v with the same throttle 36v and a 36v 4.4ma battery from an hoverboard

@valerioaltei530

7 жыл бұрын

Richard Talbot and one more thing where do I connect the yellow wire from the throttle? I know it needs to go to a positive but which one on the controller? Thank you

@ebikerich

7 жыл бұрын

Valerio Altei Yellow goes to positive side of battery if it's for the throttle battery meter. Are the 3 throttle wires connected correctly ie Pos Neg and signal? Double check wiring

@valerioaltei530

7 жыл бұрын

yes the 3 wires are connected. so basically the yellow wire goes directly on the positive from the battery? another thing im trying to test it without the swtich on and off install. would it run without the switch. thank you

Would 3 of these be ok? Turnigy 5000mah 3S 11.1v 20C-30C Lipo Battery

@ebikerich

7 жыл бұрын

Danny Walker sounds good!

Did u use a bms?

Any chance you could post a link to all the parts you bought? im in London and not having much luck..

@ebikerich

7 жыл бұрын

Controller: www.ebay.co.uk/itm/281740495530 Throttle: www.ebay.co.uk/itm/262675550487 Lipo packs: MultiStar High Capacity 3S 5200mAh Multi-Rotor Lipo Pack for QR X350 PRO hobbyking.com/en_us/multistar-high-capacity-3s-5200mah-multi-rotor-lipo-pack-for-qr-x350-pro.html Charger: Turnigy B6 PRO 50W 6A Balance Charger (White) hobbyking.com/en_us/turnigy-b6-pro-50w-6a-balance-charger-white.html These are all the first ones I came across there are others cheaper(china) and more expensive. You'll need a parallel charging board to charge at least 3 lipo packs = 44.4V also some heat shrink(ebay) and fuse and holder(local car parts shop). I have a RC shop where I live so I go there for XT60 connectors but you can get them on eBay again. Hope that helps. I'm considering drilling some holes in my motor face plates to keep it cooler as it gets hot when I ride it. Just bare that in mind when doing this project.

@AlpsLifee

7 жыл бұрын

wow you are amazing! so I have to charge the batteries out of the scooter right? what is the heat shrink for? would it be safe to find some sort of material that displaces heat underneat the footplate so that it spreads it out? is there a specific fuse that I need to get? are the xt60 connectors to connect the batteries? also how long do the batteries last for if you went full throttle contiously? obvioulsy because its faster you go further but im wondering if I can get 20 minutes or more out of it?

@AlpsLifee

7 жыл бұрын

I also have another question, do I not need to purchase a new motor?

Could we have the Ebay link to the controller (and batteries if possible)? Thanks!

@emiller190

7 жыл бұрын

zayd abbas I

could you send me a link to buy all parts for upgrade just got this scooter but I want to make it fast like this

@montemahler6766

7 жыл бұрын

p0gg of Yeshua HaMashiach has it worked?

@darkkrimson_7270

6 жыл бұрын

Has it worked

Hi Rich, what controller did you used for this and where can I get this throttle with the leds? I would appreciate it your help, thank you

@ebikerich

4 жыл бұрын

Hi the parts are all from ebay. Cheap as possible!

@ryujiyamazaki583

4 жыл бұрын

@@ebikerich ok that's fine but whats the specs of the controller?

@ebikerich

4 жыл бұрын

@@ryujiyamazaki583 its a 500W 48V brushed controller

@ryujiyamazaki583

4 жыл бұрын

@@ebikerich Thank U☺

@ryujiyamazaki583

3 жыл бұрын

@@ebikerich Hi, 500W 48V brushed controller on a 350W 24V, is that possible? Will that not burn the motor?

If I modified my e200, or got a e300 I would get wheels that can hold up to 245 lbs and order off-roading wheels. I would turn it into a scooter used for sport. “Scooter-cross”

Hi, Did you change the original motor?

@ebikerich

7 жыл бұрын

D7RN no its the original motor

Can you link to the batteries you bought? Quite a few on hobby king. Thanks.

@ebikerich

4 жыл бұрын

Hi this was a few years ago. Heres a good price equivalent hobbyking.com/en_us/turnigy-5000mah-6s-20c-lipo-pack-w-xt-90.html?queryID=27c31e7b81ab8ec2e612de32e9120ad0&objectID=69105&indexName=hbk_live_magento_en_us_products

@angstfree2008

4 жыл бұрын

Ebike Rich thanks. How many of these did you say you have hooked up in the scooter?

@ebikerich

4 жыл бұрын

@@angstfree2008 there's 3 in series bud 👍

Hello mate,you have how much range with this modified scooter?

@ebikerich

7 жыл бұрын

Alper Gökcek we're getting a safe range of about 22 miles with a 10,800mAh pack and a rider weight of 25KG

@saudade2745

4 жыл бұрын

@@ebikerich 25kg? I didnt know farts could ride scooters

@maxl7827

3 жыл бұрын

@@saudade2745 😂😂nice on dude!

do you have to take it all apart to recharge it?

@ebikerich

7 жыл бұрын

michael overill yes at the mo. BMS would allow you to charge in the scooter but not got round to that yet

What's the control module called ?

@ebikerich

7 жыл бұрын

oscar ramirez ramirez 48v 800w - 1KW brushed controller. About £12 to UK from China. Works perfectly

How many batteries do I need to buy?

@ebikerich

7 жыл бұрын

Marco Ramirez depends what voltage you plan to run and what chemistry you are going to use! I'm using Lipo in a 12S configuration 3.7V per cell and 12 cells in series = 44.4V average. Which is perfect for my controller which is a 48V and has a low voltage cut off of 42v or 3.5V per cell

Does he know something is burning?

where can i buy lipo batteries

@ebikerich

7 жыл бұрын

Jose Garcia I get mine from hobby king but also try ebay

hey if i change the controller to 48v 800w and a 24v motor (the standerd e300 motor) will it work? and i get a 36v battery

@ebikerich

7 жыл бұрын

Haiqal Rock. The cutoff for a 48V controller will be lower than your 36V battery max voltage so will probably not work. Go for a 36V controller and it'll work fine.

@haiqalhalfis6680

7 жыл бұрын

Richard Talbot ouh so i need to find a 36v controller and 36v battery so that the motor can work?

@ebikerich

7 жыл бұрын

Haiqal Rock yes that's the best option. 36V will be a good increase in speed!

Where did you get the batteries?

@ebikerich

4 жыл бұрын

Hobbyking

Am i right the motor is stock? So you overvolt it?

@ebikerich

7 жыл бұрын

Cosmo John yep you are correct.

@arrowstheorem1881

7 жыл бұрын

Richard Talbot Thanks so much for your prompt response! Enjoyed your videos! I have a similar scooter. Its a Razor clone from China. So your video on Razor is very useful to me!

You didn’t burn out stock motor

can u charge the battery in the scooter or do u have to take the scooter apart

Is this scooter worth getting or no ??? Was going to get 1????

@ebikerich

7 жыл бұрын

Rob Flook if u can get one cheap I'd go for it. Does the job!

@lordjimmyjimbok3067

7 жыл бұрын

Richard Talbot I got one couldn't help myself I'm 12 and half stone so should be ok for me thanks for message👍👍

@ebikerich

7 жыл бұрын

Rob Flook no worries hope you have fun on it. Let me know how u get on with it

@lordjimmyjimbok3067

7 жыл бұрын

Richard Talbot I got my 2 12 year old the E200 for Christmas and wanted to have some fun with them I haven't opened mine yet waiting for Christmas lol any tips on charging them mate

@ebikerich

7 жыл бұрын

Rob Flook not really mate if they're standard just plug em in and wait till the light goes green. Bit more complicated if you modify them though. Have fun!

I saw the throttle it looks like a motability

@ebikerich

8 жыл бұрын

It's a Chinese Hall Throttle just £10 on eBay

Hi led display no green bars only red (lo) ignition on but nothing else

@ebikerich

5 жыл бұрын

Is the battery voltage correct for the throttle you bought?

@garyalbright1982

5 жыл бұрын

Richard Talbot Hi Ricnard thanks for replying 12 v to 240 controller plus variable speed throttle for led display yellow to yellow or orange but colours all different all else fine

Where did you get the parts from

@ebikerich

7 жыл бұрын

rich housley mostly eBay but batteries from Hobby King

are you smoking? or was that the scooter? 5:23

@6abdelaziz

7 жыл бұрын

smoking you can sée thé cigarette

@flakito011503

7 жыл бұрын

Wesley Schultz probably the scooter, 48 volts will fry the 24 volt 250 watt motor on these scooters in matter of seconds😂

You sound like salad fingers ;) :D

Lipos are the answer to help with performance. You can shave around 16 lbs off of battery weight compared to two sla batteries. In an application like this, every pound counts.

48 volt batteries????? stock circuit breaker,stock motor really??? the circuit breaker will pop out every second to protect the weak components from getting fry

@ebikerich

7 жыл бұрын

flakito011503 no!

30mph? wow, thats the maximum speed a 16 y/o can go on a scooter (motorcycle) in the uk!

@88superpop

5 жыл бұрын

The UK has my respect but it seems like the laws of the land are getting stricter and more overbearing by the year

This video seems to be a lot of............. nothing. No build instructions, no good pictures.... just some rambling guy talking without thinking in advance what he is going to say.