Puch Maxi transmission fluid change in 8 steps

Автокөліктер мен көлік құралдары

Changing the transmission oil on a Puch Maxi E50 engine in eight simple steps, oil used is S2 ATF AX however any sort of multi purpose Automatic Transmission Fluid should work.
Artwork in the end card was done by @Meiko_Verana
Music is Kevin MacLeod: Inspired

Пікірлер: 12

  • @geraldscott4302
    @geraldscott43028 ай бұрын

    It is fine to leave it on the stand. I use a cut off 2 liter pop bottle to drain the oil into. Hold it up close to the drain plug, remove plug, after it gets to where it is just dripping, set the cut off bottle on the floor. The drips will not hit the stand. Make sure the washer is good, or replace it. It won't do any good to put Loctite on the plug. The threads in the case are covered with oil, so Loctite won't work. I use a 1/4" drive ratchet and just barely snug it up. The E50 uses Type F ATF. No need to measure it. With the moped sitting on the centerstand, pour fluid in the filler hole until it reaches the top, and put the plug back in. I welded a piece of a large diameter washer onto the end of a screwdriver. It is wide enough to prevent chewing up the slot in the plug. Clean up any spilled oil. I use spray carb cleaner or brake cleaner to clean the plugs, and around the plugs before removing them. SAVE THE PLANET!!!!!!!!! CRUSH A TESLA!!!!!!!!!

  • @senpeibaum1574
    @senpeibaum1574 Жыл бұрын

    cooles Video werde es nächste Woche an meiner Oma ausprobieren

  • @thea6m293

    @thea6m293

    Жыл бұрын

    why does your grandma require and oil change

  • @wece5401
    @wece5401 Жыл бұрын

    Very good trans(m)itions, I'd even say they were fluid, almost like they were lubricated properly.

  • @he_exe

    @he_exe

    Жыл бұрын

    🤣

  • @jimkerman2859
    @jimkerman2859 Жыл бұрын

    Joey was Here!!!!!

  • @thea6m293
    @thea6m293 Жыл бұрын

    YEEEEEEEEEEEEEEEEET

  • @thea6m293
    @thea6m293 Жыл бұрын

    3:56 CUP

  • @rasmus1600
    @rasmus1600 Жыл бұрын

    Instead of having to meassure the oil, just let the moped rest in a straight position and fill oil untill it comes out of the oil fill port. That's the amount you need. Easier and less mess. Even the original manual said to do that.

  • @he_exe

    @he_exe

    11 ай бұрын

    Well you are correct however to get the right ammount using that methode, you need the moped to be perfectly level which might be inconveniant for some people. I mean theres a reason why the oil volumes are known in the first place.

  • @rasmus1600

    @rasmus1600

    11 ай бұрын

    @@he_exe I know, I've always done it that way and the rest of my friends with 90kmph tuned Maxis does it the same way. I've never had a problem with it, other than a bad engine case seal so it leaked a bit too much oil :D

  • @he_exe

    @he_exe

    11 ай бұрын

    ​@@rasmus1600 you are right as rain again, but I still feel like with informatiol im putting on the internet tho I should be on the safe side 😅

Келесі