for cooling ahould add a little small water pump for the pick up's that don't get enough water.

Congrats on your PB Thats a nice spot to run them Enjoyed it and watched a couple times 🤙

@H2oMechanic2RC

3 ай бұрын

I tend to watch my own Videos multiple times bc its fun to enjoy it again and again. Thanks for your support

The Impulse ripped on 8S! Great speed, congrats. That is a beautiful spot to run your boats too. Only those poles in the water.. hopefully they're not magnetic 😅

Running great in that chop, maybe I need those tabs!! My pb is 86mph with this boat on 8s with an 1817. Haven't had much luck keeping it down beyond that....

@H2oMechanic2RC

3 ай бұрын

That's sets the bar pretty high!

Congratulations man, that's a good run! Surprised how well that system took 8s.

Congrats!! Great Run!

Love all your videos great job. I have been working on my dominator for max speed, after much work, and some bad crashes, I have now reached my PB of 94 mph (8s no flips) I think I remember in one of your videos you were trying to decide which boat to keep, I would definitely recommend the dominator. I have only been in the Hobby for one year totally love it and like you seem to be I am addicted boat gang forever. GO BIG B! Thanks again for the great videos. Mark Gambetta

@H2oMechanic2RC

3 ай бұрын

I got my Dom upto 66 yesterday on 6s. But I'm running a 1800kv motor. My self righting hull is a huge limiting factor for space. I'll be installing a SVM 2130kv in the Dom soon and see what I can get out of it.

prop angle should be from straight it should be 85 to 70 degree angle up from straight if you set the prop around there and you find the best setting it will be in that range from what i know.

Get a boat bitz rudder kit on there and your temps will drop, it has way bigger outlets that dont restrict water flow

Great content really enjoy your videos, very knowledgeable! I have qualified question for you, one of my boat is the pro boat sonic wake and I really love that boat but the last two times I’ve taken it out it cuts out! What I mean is once it’s in the water everything is green and good to go and so I throttle up and get to nearly 2/3 a trigger and then it cuts out and then it will run again get about 2/3 of trigger and when I bring it in the esc is blinking red! Do you know hat is going on

@H2oMechanic2RC

3 ай бұрын

Esc is likely kicking out on "amp cut". Too big of prop your running or your batteries are old or too Low of C Rating. Or possibly you have a binding issue in the Driveline causing high amps.

Man you need to not be running to get speed in that rough water. Wind the trim tabs back up and be patient and wait for flat water don’t touch any other setting and don’t waste your flat water by doing half and 3/4 pace runs.By doing it this way you can hold it flat out for way longer as there will be no waves to worry you and you’ll get much more speed. On top of that If you can warm your batteries before you do the run you go even faster. I have found without warming my batteries the second full speed run is faster than my first run but the batteries are not at their highest voltage on the second pass so warming them will get even better speed on that first flat out run. For that kind of water man she’s stable great work on the tuning. I found one of my boats ran cooler and way faster on 8s same exact set up as 6s go figure. I think 60 Celsius is the limit for heat 120 f on that motor shows it can handle 8s I would leave it, I mean what the worst it can do.

I love the impulse. I want one of those or the delta force 35 hull and hardware kit. I’m about to retire my spartan, I’m at its limits and it won’t hold the power

@H2oMechanic2RC

3 ай бұрын

Have you seen the new Self Righting Spartan! I love the size, just with it was a Fiberglass hull

@jaycevessier7554

3 ай бұрын

@@H2oMechanic2RC yep, seen it and that new bad ass trailer. I’m just done with trying to make my spartan fast. It just won’t stay stable over 63mph, it just goes crazy.

@H2oMechanic2RC

3 ай бұрын

@jaycevessier7554 I'm going to open up my Spartan and do a Carbon Inlay & a different motor tray. Just something different.

@jaycevessier7554

3 ай бұрын

@@H2oMechanic2RC I wonder if the carbon inlay would stiffen the hull up? Cause I believe that’s the whole issue. Also I like how the inside of the new spartan is designed, to where you can run the batteries in the center. I think the batteries being on each side is what causes the chine walking

@H2oMechanic2RC

3 ай бұрын

@@jaycevessier7554 100% batteries need to be centered in the bottom

Motors for what i know only know heat...not voltage! You can go safe on higher voltage with a smaller prop for less heat and less amperage and more speed then less voltage with big prop that causes more amperage with more heat cause effeciency is on the table...and a big prop is generally useless unless you try them all to find one that actually does not disturb the handling... That's what i learned from myself! Happy boating my friend!