Thank you Pro-Line, you make SUPER good parts. Unbelievable!

thanks for video was very helpful. just purchased faultline 2.2 wheel with sand paw 2.2 tires and am thrilled to try them

Rockin this exact set up on my slash 2wd exept i have those same rims on the front but I got the split six for the back I didn't notice until I got home lmao they looked so similar on the shelf and I just grabbed them without really looking, it's cool tho I like the look.

I wish you guys still made the Masher tires. I had a set on my Revo 3.3 and they were awesome!

@markoftheus

7 жыл бұрын

They do still make the Masher tires, I'm just not sure if they make them in a 3.8 size. The 3.8 Trenchers are also pretty good.

Ok tks god bless you

I just ordered the f11 beadlocs from proline for my losi tenacity are they compatible with all 2.2 SCT tires or are they specifically made to only hold proline tires??

Do you need specific tires. I purchased these and used aka gridiron tires. Spun out of them in 2 laps.

Will these rims stay on the tire if you balloon them alot and stuff? Have a bandit Vxl and it makes glued tires come off the rims alot, but will these hold up better?

What would be a stiffer replacement foam that would work with these 2.2/3.0 beadlock rims?

Why 2.2/3" bead-lock wheels are not available with 17mm Hex from Proline ?

@markoftheus

7 жыл бұрын

1/10 scale short course trucks use 12mm hexes, standard these days, ever since the Traxxas Slash came out and maybe a little bit before.

Did anybody use these for the drag tires

so are the f-11 made for brushless power on my slash 4x4? i think the 6 split spoke aren't made for brushless power is says

@markoftheus

7 жыл бұрын

Don't always trust what tower hobbies says. I have the split six bead-loc wheels on my brushless powered and lipo powered HPI Blitz ESE and they're doing just fine.

thank you! where can i get that power tool?

@ProLineRacingYT

8 жыл бұрын

+chris boshears It's a Makita DF010D and you can pick one up at most hardware stores..

Is that red outer beads aluminum or plastic?

@ProLineRacingYT

5 жыл бұрын

The outer ring is cast-metal

They look great but the inner wall always seems to fly off no matter what. The plastic threads don't help, maybe a bolt through setup...they seem to a bit on the heavy side too.

what size allen key did you use

@pixicated

7 жыл бұрын

Hello Federiko, the screws have a 2mm hex

Hi what's better glue or those

@ProLineRacingYT

5 жыл бұрын

Hello Manuel, the best thing about Bead-Locs is that you can switch out your tires easily for different terrains. while our bead-locs are designed to hold our Tires TIGHT, choosing a glued tire/wheel combo will definitely offer the strongest hold of your bead. this is usually ideal for a race scenario where a pulled bead could be detrimental to your lap time, however, on the flip side, if you pull a bead on a bead-loc, you just loosen it up, re-position and then tighten it back down! :) its really your choice, both options are good.

No glue?

@prolinevideo2389

7 жыл бұрын

That is correct, no glue is required, this is a real bead-loc system!

@markoftheus

7 жыл бұрын

Indeed! Gluing and un-gluing tires, especially 2.8's, are kind of a mess.

Use silicone in place of glue so u can still change out tires. Running on 3s will still cause tires to blow off of rims. Not nearly as easy as regular wheels but it still happens

@multipreach2674

5 жыл бұрын

I found the glued tyres on 3s hold out pretty well, these come off after any form of hard driving.

@lunseren

Жыл бұрын

Will the beadlocks blow off the tire or are they better then glued?

dude??? close up?? I can't see what your talking about

@weedsnager

3 жыл бұрын

Agreed !