In video 3 of my pontoon rebuild I am installing the deck, vinyl flooring, and painting the fence.
Жүктеу.....
Пікірлер: 47
@rockcrusher46363 жыл бұрын
Nice job, keep em coming.
@MrJmattr33 жыл бұрын
It’s looking good!
@GgKustomz3 жыл бұрын
Looking good!
@zacheryandersen Жыл бұрын
An idea for future restorers to make stapling the vinyl edge faster: Clamp the edge guards down to use as a fence to slide the stapler down. Then you can really lay some fasteners down quickly. Also, make sure you're compressor is putting out the right amount of psi per strike.
@jeffparcel Жыл бұрын
For cheaper than a few drill bits, you can use a small box of machine screws to drill out the rivets
@rolands417511 ай бұрын
👌
@MrCleary21 Жыл бұрын
What kind of paint and priner do you use for the aluminum side walls ?
@kibbeekelley719511 ай бұрын
Did you keep track of how many hours it took to replace the deck by chance? Love the Channel, thank you!
@to5msheppard2 жыл бұрын
Great video I only have one question when you have leftovers on the sides why not wrap it around the edges was my only thought to protect the word other than that I love watching your videos helping me do mine
@TJLawrence254
2 жыл бұрын
Good question. The end grains of the plywood need to be able to breathe. Because marine wood is only made with water proof glue and not chemically treated like green wood. It needs an avenue to expand and contract with humidity. If you seal it up too much the wood will hold moisture and rot.
@vicentenavarroreyes1378
Жыл бұрын
@
@novoiperkele3 жыл бұрын
The low aluminium was there to prevent stuff from ending up in the water.
@TJLawrence254
3 жыл бұрын
That makes sense. I added full height aluminum to keep the water from splashing in. Check it out kzread.info/dash/bejne/ZKSZxZlmc7zTic4.html
@miorieser32107 ай бұрын
Je mehr Pontoons, desto höher der Meeresspiegel.
@ashmontrealty7 ай бұрын
tJ I am thinking about painting my railings black. do you rememember what primer you used and paint and did it hold up over time?
@MrWszola Жыл бұрын
How did that paint hold up without clear? Would you recommend a different paint after a summer on the water?
@TJLawrence254
Жыл бұрын
There are a few scratches after a year. A clear coat or roughing up the bare aluminum before the primer would have helped.
@eddiesandoval3560Ай бұрын
Where did you get the vinyl flooring?
@erizbelphantom37182 жыл бұрын
Hey great work! Did you sand down the rails or just painted over it?
@TJLawrence254
2 жыл бұрын
I sanded them down first.
@ChrisJones-yn8xk
Жыл бұрын
@@TJLawrence254 why didn't you paint the plywood on both sides to protect from water
@TJLawrence254
Жыл бұрын
@@ChrisJones-yn8xk it's rosewood bonded with waterproof glue. Rosewood is naturally rot resistant. If you paint it moisture will be trapped in the wood and it will warp over time. The glue used to bond the flooring is designed for bonding directly to wood and won't stick to painted or treated surfaces.
@ChrisJones-yn8xk
Жыл бұрын
@@TJLawrence254 thank you for the quick response I'm fixing to do my pontoon and that makes sense thanks
@TJLawrence254
Жыл бұрын
@@ChrisJones-yn8xk you're welcome! I hope your restoration gos well! Let me know if you have anymore questions.
@Baynesters3 жыл бұрын
how long does it take from start to finish, looks great too
@TJLawrence254
3 жыл бұрын
I've been working on it for about 8 hours a weekend for two months. Probably have another month of weekends to go. I'm estimating 80 to 100 hours total.
@TheOwen1974
3 жыл бұрын
@@TJLawrence254 Agreed!
@mikebelcher6692 Жыл бұрын
is that the factory transom? I have a 76 and mine is narrower and steel. Im thinking about having a wider aluminum one fabbed
@TJLawrence254
Жыл бұрын
No, I got the transom from Craigslist. The original one was pretty flimsy.
@logandion6308 Жыл бұрын
where did you get the flooring? how much did it cost? and how is it holding up?
@TJLawrence254
Жыл бұрын
I think I got it from everythingpontoon.com it was a about $300. Still holding up great!
@andersonsingleton80172 жыл бұрын
What kind of paint did you use, did you add a clear coat and where did you buy the paint from, how much paint did you use and where did you get the paint gun from, thanks for the video
@TJLawrence254
2 жыл бұрын
I used Rust-Oleum aluminum primer and paint. About a quart of primer and half gallon of paint. Applied with a husky brand HVLP spray gun kit. All from the Home Depot. I didn't use a clear coat but over time that probably would be beneficial.
@stevelaborde7945
2 жыл бұрын
@@TJLawrence254 did you have to add any additives to use this paint in the HVLP gun?
@TJLawrence254
2 жыл бұрын
@Steve Laborde I just thinned it out. It could probably benefit from an adhesion additive, but I don't know enough about paints yet to recommend anything.
@stevelaborde7945
2 жыл бұрын
@@TJLawrence254 same here when it comes to painting lol, I noticed it was a latex paint that why I asked, I may try to find an oil based paint to prevent me from thinning it out. Great videos and your pontoon looks amazing!
@jakeowens1770
Жыл бұрын
@@TJLawrence254 mix radio 2:1? With thinner?
@carsonthomas32303 жыл бұрын
What kind of vinyl did you use? Where did you get it?
@TJLawrence254
3 жыл бұрын
I used Stone Grey 80mil vinyl manufactured by Marideck. Got it from EverythingPontoon.com
@brentkennedy28142 жыл бұрын
Just wondering if you painted the underneath of your plywood?
@TJLawrence254
2 жыл бұрын
I did not. The wood manufacturer recommend against sealer or painting the bottom side. The glue used to hold the rosewood plys together is designed for direct water contact.
@hardrockminer-50
2 жыл бұрын
That was my question too. I am considering spraying on a sealant like Thompsons Water Seal. We get a wet line in the carpet from beneath when we get any rough water.
@mikebelcher6692
Жыл бұрын
@@hardrockminer-50 i sealed my marine deck and it wqs the wrong thing to do. It got moisture in certain spots and the wood couldn’t dry out. Its been 15 years but now I have to strip and go back with new marine decking
@joelbuyno5500 Жыл бұрын
Put harder in your paint it will dry faster.if you didn't
@TJLawrence254
Жыл бұрын
Thanks! I didn't think to do that but will next time.
@ronhanish Жыл бұрын
keep that dewalt battery on concrete and it will kill the battery
Пікірлер: 47
Nice job, keep em coming.
It’s looking good!
Looking good!
An idea for future restorers to make stapling the vinyl edge faster: Clamp the edge guards down to use as a fence to slide the stapler down. Then you can really lay some fasteners down quickly. Also, make sure you're compressor is putting out the right amount of psi per strike.
For cheaper than a few drill bits, you can use a small box of machine screws to drill out the rivets
👌
What kind of paint and priner do you use for the aluminum side walls ?
Did you keep track of how many hours it took to replace the deck by chance? Love the Channel, thank you!
Great video I only have one question when you have leftovers on the sides why not wrap it around the edges was my only thought to protect the word other than that I love watching your videos helping me do mine
@TJLawrence254
2 жыл бұрын
Good question. The end grains of the plywood need to be able to breathe. Because marine wood is only made with water proof glue and not chemically treated like green wood. It needs an avenue to expand and contract with humidity. If you seal it up too much the wood will hold moisture and rot.
@vicentenavarroreyes1378
Жыл бұрын
@
The low aluminium was there to prevent stuff from ending up in the water.
@TJLawrence254
3 жыл бұрын
That makes sense. I added full height aluminum to keep the water from splashing in. Check it out kzread.info/dash/bejne/ZKSZxZlmc7zTic4.html
Je mehr Pontoons, desto höher der Meeresspiegel.
tJ I am thinking about painting my railings black. do you rememember what primer you used and paint and did it hold up over time?
How did that paint hold up without clear? Would you recommend a different paint after a summer on the water?
@TJLawrence254
Жыл бұрын
There are a few scratches after a year. A clear coat or roughing up the bare aluminum before the primer would have helped.
Where did you get the vinyl flooring?
Hey great work! Did you sand down the rails or just painted over it?
@TJLawrence254
2 жыл бұрын
I sanded them down first.
@ChrisJones-yn8xk
Жыл бұрын
@@TJLawrence254 why didn't you paint the plywood on both sides to protect from water
@TJLawrence254
Жыл бұрын
@@ChrisJones-yn8xk it's rosewood bonded with waterproof glue. Rosewood is naturally rot resistant. If you paint it moisture will be trapped in the wood and it will warp over time. The glue used to bond the flooring is designed for bonding directly to wood and won't stick to painted or treated surfaces.
@ChrisJones-yn8xk
Жыл бұрын
@@TJLawrence254 thank you for the quick response I'm fixing to do my pontoon and that makes sense thanks
@TJLawrence254
Жыл бұрын
@@ChrisJones-yn8xk you're welcome! I hope your restoration gos well! Let me know if you have anymore questions.
how long does it take from start to finish, looks great too
@TJLawrence254
3 жыл бұрын
I've been working on it for about 8 hours a weekend for two months. Probably have another month of weekends to go. I'm estimating 80 to 100 hours total.
@TheOwen1974
3 жыл бұрын
@@TJLawrence254 Agreed!
is that the factory transom? I have a 76 and mine is narrower and steel. Im thinking about having a wider aluminum one fabbed
@TJLawrence254
Жыл бұрын
No, I got the transom from Craigslist. The original one was pretty flimsy.
where did you get the flooring? how much did it cost? and how is it holding up?
@TJLawrence254
Жыл бұрын
I think I got it from everythingpontoon.com it was a about $300. Still holding up great!
What kind of paint did you use, did you add a clear coat and where did you buy the paint from, how much paint did you use and where did you get the paint gun from, thanks for the video
@TJLawrence254
2 жыл бұрын
I used Rust-Oleum aluminum primer and paint. About a quart of primer and half gallon of paint. Applied with a husky brand HVLP spray gun kit. All from the Home Depot. I didn't use a clear coat but over time that probably would be beneficial.
@stevelaborde7945
2 жыл бұрын
@@TJLawrence254 did you have to add any additives to use this paint in the HVLP gun?
@TJLawrence254
2 жыл бұрын
@Steve Laborde I just thinned it out. It could probably benefit from an adhesion additive, but I don't know enough about paints yet to recommend anything.
@stevelaborde7945
2 жыл бұрын
@@TJLawrence254 same here when it comes to painting lol, I noticed it was a latex paint that why I asked, I may try to find an oil based paint to prevent me from thinning it out. Great videos and your pontoon looks amazing!
@jakeowens1770
Жыл бұрын
@@TJLawrence254 mix radio 2:1? With thinner?
What kind of vinyl did you use? Where did you get it?
@TJLawrence254
3 жыл бұрын
I used Stone Grey 80mil vinyl manufactured by Marideck. Got it from EverythingPontoon.com
Just wondering if you painted the underneath of your plywood?
@TJLawrence254
2 жыл бұрын
I did not. The wood manufacturer recommend against sealer or painting the bottom side. The glue used to hold the rosewood plys together is designed for direct water contact.
@hardrockminer-50
2 жыл бұрын
That was my question too. I am considering spraying on a sealant like Thompsons Water Seal. We get a wet line in the carpet from beneath when we get any rough water.
@mikebelcher6692
Жыл бұрын
@@hardrockminer-50 i sealed my marine deck and it wqs the wrong thing to do. It got moisture in certain spots and the wood couldn’t dry out. Its been 15 years but now I have to strip and go back with new marine decking
Put harder in your paint it will dry faster.if you didn't
@TJLawrence254
Жыл бұрын
Thanks! I didn't think to do that but will next time.
keep that dewalt battery on concrete and it will kill the battery
Zoom 0